[PATCH v5 04/13] gpu: nova-core: gsp: pass GspBootContext to unload methods

[Alexandre Courbot <acourbot@nvidia.com>]

`GspBootContext` contains the resources required to boot the GSP. As it
turns out, this is also the context required for unloading it.

Reflect that fact by replacing the arguments of `Gsp::unload` and
`UnloadBundle::run` with the `GspBootContext`. This symmetry between
`Gsp::boot` and `Gsp::unload` will also be convenient when we want to
make these methods generic over the boot context corresponding to the
boot method used.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Eliot Courtney <ecourtney@nvidia.com>
---
 drivers/gpu/nova-core/gpu.rs           | 19 ++++++++++++++++---
 drivers/gpu/nova-core/gsp/boot.rs      | 28 +++++++++++++---------------
 drivers/gpu/nova-core/gsp/hal.rs       | 15 +--------------
 drivers/gpu/nova-core/gsp/hal/gh100.rs | 17 ++++-------------
 drivers/gpu/nova-core/gsp/hal/tu102.rs | 23 +++++++++++------------
 5 files changed, 45 insertions(+), 57 deletions(-)

diff --git a/drivers/gpu/nova-core/gpu.rs b/drivers/gpu/nova-core/gpu.rs
index 43c3f4f8df71..32bfa0be2357 100644
--- a/drivers/gpu/nova-core/gpu.rs
+++ b/drivers/gpu/nova-core/gpu.rs
@@ -269,7 +269,9 @@ fn fmt(&self, f: &mut fmt::Formatter<'_>) -> fmt::Result {
 #[pin_data(PinnedDrop)]
 struct GspResources<'gpu> {
     /// Device owning the GPU.
-    device: &'gpu device::Device<device::Bound>,
+    device: &'gpu pci::Device<device::Bound>,
+    /// Details about the chipset.
+    spec: Spec,
     /// MMIO mapping of PCI BAR 0.
     bar: Bar0<'gpu>,
     /// GSP falcon instance, used for GSP boot up and cleanup.
@@ -312,7 +314,16 @@ fn drop(self: Pin<&mut Self>) {
             .gsp
             .as_ref()
             .get_ref()
-            .unload(device, bar, &*this.gsp_falcon, &*this.sec2_falcon, bundle)
+            .unload(
+                GspBootContext {
+                    pdev: device,
+                    bar,
+                    chipset: this.spec.chipset,
+                    gsp_falcon: &*this.gsp_falcon,
+                    sec2_falcon: &*this.sec2_falcon,
+                },
+                bundle,
+            )
             .inspect_err(|e| dev_err!(device, "failed to unload GSP: {:?}\n", e));
     }
 }
@@ -344,7 +355,9 @@ pub(crate) fn new(
             sysmem_flush: SysmemFlush::register(pdev.as_ref(), bar, spec.chipset)?,
 
             gsp_resources <- try_pin_init!(GspResources {
-                device: pdev.as_ref(),
+                device: pdev,
+
+                spec: *spec,
 
                 bar,
 
diff --git a/drivers/gpu/nova-core/gsp/boot.rs b/drivers/gpu/nova-core/gsp/boot.rs
index 536f2e341c01..75054424a951 100644
--- a/drivers/gpu/nova-core/gsp/boot.rs
+++ b/drivers/gpu/nova-core/gsp/boot.rs
@@ -3,7 +3,6 @@
 
 use kernel::{
     bits,
-    device,
     dma::Coherent,
     io::poll::read_poll_timeout,
     prelude::*,
@@ -15,7 +14,6 @@
     driver::Bar0,
     falcon::{
         gsp::Gsp,
-        sec2::Sec2,
         Falcon, //
     },
     fb::FbLayout,
@@ -47,7 +45,6 @@ pub(crate) fn boot(
         let bar = ctx.bar;
         let chipset = ctx.chipset;
         let gsp_falcon = ctx.gsp_falcon;
-        let sec2_falcon = ctx.sec2_falcon;
         let dev = pdev.as_ref();
         let hal = super::hal::gsp_hal(chipset);
 
@@ -61,9 +58,11 @@ pub(crate) fn boot(
         // Perform the chipset-specific boot sequence, and retrieve the unload bundle.
         let unload_bundle = hal.boot(&self, &ctx, &fb_layout, &wpr_meta)?;
 
-        let unload_guard = ScopeGuard::new_with_data(unload_bundle, |unload_bundle| {
-            let _ = self.unload(dev, bar, gsp_falcon, sec2_falcon, unload_bundle);
-        });
+        let unload_guard =
+            ScopeGuard::new_with_data((ctx, unload_bundle), |(ctx, unload_bundle)| {
+                let _ = self.unload(ctx, unload_bundle);
+            });
+        let ctx = &unload_guard.0;
 
         gsp_falcon.write_os_version(gsp_fw.bootloader.app_version);
 
@@ -82,12 +81,12 @@ pub(crate) fn boot(
         self.cmdq
             .send_command_no_wait(bar, commands::SetRegistry::new())?;
 
-        hal.post_boot(&self, &ctx, &gsp_fw)?;
+        hal.post_boot(&self, ctx, &gsp_fw)?;
 
         // Wait until GSP is fully initialized.
         commands::wait_gsp_init_done(&self.cmdq)?;
 
-        Ok(unload_guard.dismiss())
+        Ok(unload_guard.dismiss().1)
     }
 
     /// Shut down the GSP and wait until it is offline.
@@ -116,17 +115,16 @@ fn shutdown_gsp(
     /// This stops all activity on the GSP.
     pub(crate) fn unload(
         &self,
-        dev: &device::Device<device::Bound>,
-        bar: Bar0<'_>,
-        gsp_falcon: &Falcon<'_, Gsp>,
-        sec2_falcon: &Falcon<'_, Sec2>,
+        ctx: super::GspBootContext<'_>,
         unload_bundle: Option<super::UnloadBundle>,
     ) -> Result {
+        let dev = ctx.dev();
+
         // Shut down the GSP. Keep going even in case of error.
         let mut res = Self::shutdown_gsp(
             &self.cmdq,
-            bar,
-            gsp_falcon,
+            ctx.bar,
+            ctx.gsp_falcon,
             commands::PowerStateLevel::Level0,
         )
         .inspect_err(|e| dev_err!(dev, "GSP shutdown failed: {:?}\n", e));
@@ -136,7 +134,7 @@ pub(crate) fn unload(
             res = res.and(
                 unload_bundle
                     .0
-                    .run(dev, bar, gsp_falcon, sec2_falcon)
+                    .run(&ctx)
                     .inspect_err(|e| dev_err!(dev, "Unload bundle failed: {:?}\n", e)),
             );
         } else {
diff --git a/drivers/gpu/nova-core/gsp/hal.rs b/drivers/gpu/nova-core/gsp/hal.rs
index 851d1f24c137..849ca224085b 100644
--- a/drivers/gpu/nova-core/gsp/hal.rs
+++ b/drivers/gpu/nova-core/gsp/hal.rs
@@ -5,18 +5,11 @@
 mod tu102;
 
 use kernel::{
-    device,
     dma::Coherent,
     prelude::*, //
 };
 
 use crate::{
-    driver::Bar0,
-    falcon::{
-        gsp::Gsp as GspEngine,
-        sec2::Sec2,
-        Falcon, //
-    },
     fb::FbLayout,
     firmware::gsp::GspFirmware,
     gpu::{
@@ -37,13 +30,7 @@
 /// required for unloading is prepared at load time, and stored here until it needs to be run.
 pub(super) trait UnloadBundle: Send {
     /// Performs the steps required to properly reset the GSP after it has been stopped.
-    fn run(
-        &self,
-        dev: &device::Device<device::Bound>,
-        bar: Bar0<'_>,
-        gsp_falcon: &Falcon<'_, GspEngine>,
-        sec2_falcon: &Falcon<'_, Sec2>,
-    ) -> Result;
+    fn run(&self, ctx: &GspBootContext<'_>) -> Result;
 }
 
 /// Trait implemented by GSP HALs.
diff --git a/drivers/gpu/nova-core/gsp/hal/gh100.rs b/drivers/gpu/nova-core/gsp/hal/gh100.rs
index 18c889f9f413..aabef45202f7 100644
--- a/drivers/gpu/nova-core/gsp/hal/gh100.rs
+++ b/drivers/gpu/nova-core/gsp/hal/gh100.rs
@@ -11,10 +11,8 @@
 };
 
 use crate::{
-    driver::Bar0,
     falcon::{
         gsp::Gsp as GspEngine,
-        sec2::Sec2,
         Falcon, //
     },
     fb::FbLayout,
@@ -116,22 +114,16 @@ fn wait_for_gsp_lockdown_release(
 struct FspUnloadBundle;
 
 impl UnloadBundle for FspUnloadBundle {
-    fn run(
-        &self,
-        dev: &device::Device<device::Bound>,
-        _bar: Bar0<'_>,
-        gsp_falcon: &Falcon<'_, GspEngine>,
-        _sec2_falcon: &Falcon<'_, Sec2>,
-    ) -> Result {
+    fn run(&self, ctx: &GspBootContext<'_>) -> Result {
         // GSP falcon does most of the work of resetting, so just wait for it to finish.
         read_poll_timeout(
-            || Ok(gsp_falcon.is_riscv_active()),
+            || Ok(ctx.gsp_falcon.is_riscv_active()),
             |&active| !active,
             Delta::from_millis(10),
             Delta::from_secs(5),
         )
         .map(|_| ())
-        .inspect_err(|_| dev_err!(dev, "GSP falcon failed to halt\n"))
+        .inspect_err(|_| dev_err!(ctx.dev(), "GSP falcon failed to halt\n"))
     }
 }
 
@@ -153,7 +145,6 @@ fn boot(
         let bar = ctx.bar;
         let chipset = ctx.chipset;
         let gsp_falcon = ctx.gsp_falcon;
-        let sec2_falcon = ctx.sec2_falcon;
 
         let unload_bundle = crate::gsp::UnloadBundle(
             KBox::new(FspUnloadBundle, GFP_KERNEL)? as KBox<dyn UnloadBundle>
@@ -182,7 +173,7 @@ fn boot(
             Ok(()) => Ok(Some(unload_bundle)),
             Err(e) => {
                 // Wait for the GSP RISC-V core to halt in case of error.
-                let _ = unload_bundle.0.run(dev, bar, gsp_falcon, sec2_falcon);
+                let _ = unload_bundle.0.run(ctx);
                 Err(e)
             }
         }
diff --git a/drivers/gpu/nova-core/gsp/hal/tu102.rs b/drivers/gpu/nova-core/gsp/hal/tu102.rs
index f78e2489f5a6..c0956fb1c9cf 100644
--- a/drivers/gpu/nova-core/gsp/hal/tu102.rs
+++ b/drivers/gpu/nova-core/gsp/hal/tu102.rs
@@ -121,18 +121,15 @@ fn build(
 }
 
 impl UnloadBundle for Sec2UnloadBundle {
-    fn run(
-        &self,
-        dev: &device::Device<device::Bound>,
-        bar: Bar0<'_>,
-        gsp_falcon: &Falcon<'_, GspEngine>,
-        sec2_falcon: &Falcon<'_, Sec2>,
-    ) -> Result {
+    fn run(&self, ctx: &GspBootContext<'_>) -> Result {
+        let dev = ctx.dev();
+        let bar = ctx.bar;
+
         // Run FWSEC-SB to reset the GSP falcon to its pre-libos state.
         // Log errors but keep going if it fails.
         let fwsec_sb_res = self
             .fwsec_sb
-            .run(dev, bar, gsp_falcon)
+            .run(dev, bar, ctx.gsp_falcon)
             .inspect_err(|e| dev_err!(dev, "FWSEC-SB failed to run: {:?}\n", e));
 
         // Remove WPR2 region if set.
@@ -142,12 +139,14 @@ fn run(
                 return Ok(());
             }
 
-            sec2_falcon.reset()?;
-            sec2_falcon.load(&self.booter_unloader)?;
+            ctx.sec2_falcon.reset()?;
+            ctx.sec2_falcon.load(&self.booter_unloader)?;
 
             // Sentinel value to confirm that Booter Unloader has run.
             const MAILBOX_SENTINEL: u32 = 0xff;
-            let (mbox0, _) = sec2_falcon.boot(Some(MAILBOX_SENTINEL), Some(MAILBOX_SENTINEL))?;
+            let (mbox0, _) = ctx
+                .sec2_falcon
+                .boot(Some(MAILBOX_SENTINEL), Some(MAILBOX_SENTINEL))?;
             if mbox0 != 0 {
                 dev_err!(dev, "Booter Unloader returned error 0x{:x}\n", mbox0);
                 return Err(EINVAL);
@@ -293,7 +292,7 @@ fn boot(
         // Run the unload bundle to try and recover the GSP if an error occurs.
         let unload_guard = ScopeGuard::new_with_data(unload_bundle, |unload_bundle| {
             if let Some(unload_bundle) = unload_bundle {
-                let _ = unload_bundle.0.run(dev, bar, gsp_falcon, sec2_falcon);
+                let _ = unload_bundle.0.run(ctx);
             }
         });
 

-- 
2.55.0