[PATCH bpf-next v3 13/13] Documentation/bpf: Document up to 16-byte kfunc return values in R0:R2

[Yonghong Song <yonghong.song@linux.dev>]

kfuncs may now return a value larger than 8 bytes and up to 16 bytes (a
scalar-only struct or union, or an __int128), passed back in the R0:R2
register pair. Add a kfunc return-value section documenting this,
including that a struct or union up to 8 bytes is returned in R0 alone,
which struct and union members are accepted, that the R0:R2 register pair
requires JIT support (bpf_jit_supports_kfunc_ret_reg_pair()), and that a
return value larger than 16 bytes is unsupported.

Also note that the same convention applies to BPF subprogram returns, and
document the consequence for a global subprogram: it must assign both
halves of a register-pair return, since an unassigned R2 may be left
holding a pointer argument and is then rejected as a leak.

Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
---
 Documentation/bpf/kfuncs.rst | 62 ++++++++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/Documentation/bpf/kfuncs.rst b/Documentation/bpf/kfuncs.rst
index 1004eb0bec61..71d3ff869599 100644
--- a/Documentation/bpf/kfuncs.rst
+++ b/Documentation/bpf/kfuncs.rst
@@ -575,6 +575,68 @@ is also covered by this recovery. A kfunc handed an arena pointer may
 therefore access up to ``GUARD_SZ / 2`` past it without bounds-checking
 against the arena. Larger accesses must verify the range explicitly.
 
+2.9 kfunc Return Values
+-----------------------
+
+A kfunc may return a scalar, a pointer, or a small struct or union by
+value. A scalar or pointer of up to 8 bytes is returned in R0, as usual.
+
+A struct or union returned by value must be composed only of scalars
+(recursively), where a scalar is an integer or an enum; arrays of scalars are
+allowed as members. Its bytes are handed back to the program as the raw
+contents of R0 (and R2), so a pointer field would be laundered into a scalar
+and escape the verifier's pointer provenance and reference tracking. A struct
+or union with a pointer member is therefore rejected at load time, and so is
+one with a floating-point member, which the ABI may not return in R0:R2 at
+all.
+
+A kfunc may also return a value larger than 8 bytes and up to 16 bytes -- a
+scalar-only struct or union, or an ``__int128``. Such a value is returned
+in the register pair R0:R2, matching the convention LLVM uses for the BPF
+target: the first 8 bytes in R0 and the second 8 bytes in R2. A struct or
+union of 8 bytes or less is returned in R0 alone.
+
+::
+
+        struct bpf_pair { __u64 a, b; };   /* 16 bytes */
+
+        __bpf_kfunc struct bpf_pair bpf_kfunc_get_pair(void)
+        {
+                struct bpf_pair p = { .a = 1, .b = 2 };
+
+                return p;      /* p.a in R0, p.b in R2 */
+        }
+
+Returning a value in the R0:R2 pair requires the JIT to place the second
+half of the return value into R2, which not every architecture supports
+right now. A kfunc with a return value larger than 8 bytes is therefore
+rejected at load time on a JIT that does not advertise this capability (see
+``bpf_jit_supports_kfunc_ret_reg_pair()``), and such a program is never run
+by the interpreter. A return value larger than 16 bytes is not supported.
+
+The same R0:R2 convention applies to a BPF subprogram, global or static,
+that returns an ``__int128`` or a struct or union larger than 8 bytes. Such a
+program also requires the JIT, since the interpreter propagates only R0 out
+of a subprogram. A global subprogram is verified in isolation, so its
+by-value struct or union return is restricted to scalars just like a kfunc's;
+a static subprogram is verified inline and has no such restriction. The main
+program cannot return more than 8 bytes, as its return value is the program's
+exit code.
+
+A global subprogram must leave a scalar in *every* register of the pair, so
+both halves of the returned value have to be assigned. Leaving the upper half
+uninitialized is not merely untidy: the compiler is then free to leave R2
+holding whatever it happened to hold, which for a subprogram taking a pointer
+argument is typically that pointer. Handing the caller an unknown scalar built
+from a pointer is a leak, so the verifier rejects it with::
+
+        At subprogram exit the register R2 is not a scalar value (...)
+
+Initialize the whole return value, for example ``struct pair p = {};``, to
+avoid this. A static subprogram is exempt: it is verified inline, so an
+unassigned R2 is simply passed back to the caller as uninitialized and only a
+caller that reads it fails.
+
 .. _BPF_kfunc_lifecycle_expectations:
 
 3. kfunc lifecycle expectations
-- 
2.53.0-Meta