From: EricLin <ericlin050914@gmail.com>
To: mathias.nyman@linux.intel.com
Cc: ericlin050914@gmail.com, gregkh@linuxfoundation.org,
linux-usb@vger.kernel.org, mathias.nyman@intel.com
Subject: Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG
Date: Fri, 11 Sep 2026 20:11:05 +0800 [thread overview]
Message-ID: <20260911121107.33832-1-ericlin050914@gmail.com> (raw)
In-Reply-To: <31c54bec-2b64-4cfc-980e-9eee999aabce@linux.intel.com>
> Is this a new issue with 7.3-rc kernel, or something that can be
reproduced with older kernels?
This issue has persisted since I performed a fresh installation of Arch Linux on this device (which is Linux kernel 7.0)
> Those resets are not that frequent, often several minutes apart.
>
> First guess is that its still somehow related to power management, and device
is reset (in resume?) to recover.
Well, these messages seem to appear only when I use this fingerprint sensor
> If it works on newer kernels then git bisect can help you find the offending
commit.
> Enabling usb core and xhci dynamic debug could tell us more:
> echo 'module xhci_hcd =p' >/sys/kernel/debug/dynamic_debug/control
> echo 'module usbcore =p' >/sys/kernel/debug/dynamic_debug/control
> < Reproduce issue >
> Send output of dmesg
Here are the outputs of dmesg (with debug enabled)
[ 0.467820] xhci_hcd 0000:00:0d.0: xHCI Host Controller
[ 0.467827] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1
[ 0.468960] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810
[ 0.469267] xhci_hcd 0000:00:0d.0: xHCI Host Controller
[ 0.469269] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2
[ 0.469270] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed
[ 0.471205] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.471208] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 0.472349] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810
[ 0.472638] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.472639] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 0.472640] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed
[ 0.717291] usb 3-6: new full-speed USB device number 2 using xhci_hcd
[ 0.840784] usb 3-6: New USB device found, idVendor=27c6, idProduct=6090, bcdDevice= 1.00
[ 0.841565] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 0.841569] usb 3-6: Product: Goodix USB2.0 MISC
[ 0.841572] usb 3-6: Manufacturer: Goodix Technology Co., Ltd.
[ 0.841574] usb 3-6: SerialNumber: UIDEA968203_XXXX_MOC_B0
[ 0.957240] usb 3-7: new high-speed USB device number 3 using xhci_hcd
[ 197.151533] usb 3-6: reset full-speed USB device number 2 using xhci_hcd # The first time of using this fingerprint sensor
[ 197.401517] usb 3-6: reset full-speed USB device number 2 using xhci_hcd
[ 240.364042] xhci_hcd 0000:00:14.0: HC state intact, continuing without reset # The second time of using this fingerprint sensor
[ 240.364098] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001
[ 240.364262] xhci_hcd 0000:00:14.0: xhci_resume: starting usb3 port polling.
[ 240.364267] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb4 port polling
[ 240.364278] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 240.364280] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
[ 240.364344] xhci_hcd 0000:00:14.0: Get port status 3-1 read: 0x2a0, return 0x100
[ 240.364407] xhci_hcd 0000:00:14.0: Get port status 3-2 read: 0x2a0, return 0x100
[ 240.364418] xhci_hcd 0000:00:14.0: Get port status 3-3 read: 0x2a0, return 0x100
[ 240.364443] xhci_hcd 0000:00:14.0: Get port status 3-4 read: 0x2a0, return 0x100
[ 240.364468] xhci_hcd 0000:00:14.0: Get port status 3-5 read: 0x2a0, return 0x100
[ 240.364473] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107
[ 240.364500] xhci_hcd 0000:00:14.0: Get port status 3-7 read: 0xe63, return 0x507
[ 240.364526] xhci_hcd 0000:00:14.0: Get port status 3-8 read: 0x2a0, return 0x100
[ 240.364531] xhci_hcd 0000:00:14.0: Get port status 3-9 read: 0x2a0, return 0x100
[ 240.364537] xhci_hcd 0000:00:14.0: Get port status 3-10 read: 0x2a0, return 0x100
[ 240.364564] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107
[ 240.364611] xhci_hcd 0000:00:14.0: clear USB_PORT_FEAT_SUSPEND
[ 240.364612] xhci_hcd 0000:00:14.0: PORTSC 0663
[ 240.364616] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x663, write 0x107e1
[ 240.405029] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x7e3, write 0x10601
[ 240.405066] usb 3-6: usb auto-resume
[ 240.405138] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x400603
[ 240.405148] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 240.446041] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x40103
[ 240.446119] xhci_hcd 0000:00:14.0: clear port6 suspend/resume change, portsc: 0x603
[ 240.456987] usb 3-6: finish resume
[ 240.457379] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 240.511402] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 240.511413] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 240.517961] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 240.518038] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 240.568969] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 240.568998] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.569335] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 240.569436] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 240.569550] usb 3-6: reset full-speed USB device number 2 using xhci_hcd
[ 240.569556] xhci_hcd 0000:00:14.0: Slot already in default state
[ 240.569822] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 240.570131] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 240.605942] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 240.624155] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 240.624165] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 240.630984] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 240.631050] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 240.682009] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 240.682037] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.682206] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 240.682309] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state
[ 240.682316] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 240.682352] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.682578] xhci_hcd 0000:00:14.0: Successful setup address command
[ 240.682633] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000
[ 240.682637] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000
[ 240.682642] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000
[ 240.682644] xhci_hcd 0000:00:14.0: Internal device address = 1
[ 240.693858] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 240.693930] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80
[ 240.693941] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84
[ 240.693945] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587
[ 240.693951] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.694317] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 240.694634] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.694762] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6
[ 240.694779] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.695003] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.695040] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1
[ 240.695064] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.695313] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x103
[ 240.695616] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 240.705786] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 240.759625] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 240.759638] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 240.766960] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 240.767032] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 240.817914] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 240.817926] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.818251] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 240.818348] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 240.818446] usb 3-6: reset full-speed USB device number 2 using xhci_hcd
[ 240.818452] xhci_hcd 0000:00:14.0: Slot already in default state
[ 240.818685] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 240.818774] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 240.853852] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 240.872609] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 240.872620] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 240.878941] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 240.879016] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 240.930917] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 240.930930] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.931094] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 240.931198] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state
[ 240.931205] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 240.931220] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.931500] xhci_hcd 0000:00:14.0: Successful setup address command
[ 240.931542] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000
[ 240.931547] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000
[ 240.931552] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000
[ 240.931554] xhci_hcd 0000:00:14.0: Internal device address = 1
[ 240.943853] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 240.943921] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80
[ 240.943931] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84
[ 240.943936] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587
[ 240.943941] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.944257] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 240.944602] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.944652] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6
[ 240.944680] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.944870] xhci_hcd 0000:00:14.0: // Ding dong!
[ 240.944908] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1
[ 240.944916] xhci_hcd 0000:00:14.0: // Ding dong!
[ 241.109911] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 243.707621] xhci_hcd 0000:00:14.0: // Ding dong!
[ 243.707776] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6
[ 243.707787] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1
[ 243.707791] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 0
[ 243.707934] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x603, write 0x10661
[ 243.719855] usb 3-6: usb auto-suspend, wakeup 0
[ 243.730866] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 243.730894] xhci_hcd 0000:00:14.0: config port 4-1 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730899] xhci_hcd 0000:00:14.0: config port 4-2 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730903] xhci_hcd 0000:00:14.0: config port 3-1 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730907] xhci_hcd 0000:00:14.0: config port 3-2 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730910] xhci_hcd 0000:00:14.0: config port 3-3 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730913] xhci_hcd 0000:00:14.0: config port 3-4 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730916] xhci_hcd 0000:00:14.0: config port 3-5 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730920] xhci_hcd 0000:00:14.0: config port 3-8 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730923] xhci_hcd 0000:00:14.0: config port 3-9 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730926] xhci_hcd 0000:00:14.0: config port 3-10 wake bits, portsc: 0xa0002a0, write: 0xa0202a0
[ 243.730928] xhci_hcd 0000:00:14.0: xhci_suspend: stopping usb3 port polling.
[ 243.730936] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001
[ 243.731073] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0
[ 590.653758] xhci_hcd 0000:00:14.0: HC state intact, continuing without reset # The third time of using this fingerprint sensor
[ 590.653792] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001
[ 590.653954] xhci_hcd 0000:00:14.0: xhci_resume: starting usb3 port polling.
[ 590.653959] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb4 port polling
[ 590.653969] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 590.653971] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0
[ 590.654004] xhci_hcd 0000:00:14.0: Get port status 3-1 read: 0x2a0, return 0x100
[ 590.654029] xhci_hcd 0000:00:14.0: Get port status 3-2 read: 0x2a0, return 0x100
[ 590.654041] xhci_hcd 0000:00:14.0: Get port status 3-3 read: 0x2a0, return 0x100
[ 590.654052] xhci_hcd 0000:00:14.0: Get port status 3-4 read: 0x2a0, return 0x100
[ 590.654059] xhci_hcd 0000:00:14.0: Get port status 3-5 read: 0x2a0, return 0x100
[ 590.654065] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107
[ 590.654077] xhci_hcd 0000:00:14.0: Get port status 3-7 read: 0xe63, return 0x507
[ 590.654088] xhci_hcd 0000:00:14.0: Get port status 3-8 read: 0x2a0, return 0x100
[ 590.654094] xhci_hcd 0000:00:14.0: Get port status 3-9 read: 0x2a0, return 0x100
[ 590.654100] xhci_hcd 0000:00:14.0: Get port status 3-10 read: 0x2a0, return 0x100
[ 590.654130] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107
[ 590.654141] xhci_hcd 0000:00:14.0: clear USB_PORT_FEAT_SUSPEND
[ 590.654142] xhci_hcd 0000:00:14.0: PORTSC 0663
[ 590.654145] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x663, write 0x107e1
[ 590.694874] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x7e3, write 0x10601
[ 590.694893] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x400603
[ 590.694899] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 590.694957] usb 3-6: usb auto-resume
[ 590.735791] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x40103
[ 590.735858] xhci_hcd 0000:00:14.0: clear port6 suspend/resume change, portsc: 0x603
[ 590.747785] usb 3-6: finish resume
[ 590.748300] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x103
[ 590.748381] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 590.802405] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 590.802416] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 590.808744] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 590.808812] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 590.841739] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 590.859876] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 590.859888] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.860243] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 590.860288] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 590.860389] usb 3-6: reset full-speed USB device number 2 using xhci_hcd
[ 590.860393] xhci_hcd 0000:00:14.0: Slot already in default state
[ 590.860528] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 590.860677] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 590.914691] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 590.914704] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 590.921816] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 590.921890] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 590.972820] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 590.972840] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.972927] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 590.972957] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state
[ 590.972959] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 590.972982] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.973077] xhci_hcd 0000:00:14.0: Successful setup address command
[ 590.973099] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000
[ 590.973103] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000
[ 590.973108] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000
[ 590.973110] xhci_hcd 0000:00:14.0: Internal device address = 1
[ 590.984557] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 590.984681] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80
[ 590.984688] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84
[ 590.984691] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587
[ 590.984698] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.985041] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 590.985286] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.985342] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6
[ 590.985370] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.985541] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.985603] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1
[ 590.985612] xhci_hcd 0000:00:14.0: // Ding dong!
[ 590.986371] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 591.009222] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 591.064173] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 591.064184] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 591.069758] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 591.069829] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 591.097722] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
[ 591.120775] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 591.120787] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.121111] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 591.121136] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 591.121242] usb 3-6: reset full-speed USB device number 2 using xhci_hcd
[ 591.121247] xhci_hcd 0000:00:14.0: Slot already in default state
[ 591.121381] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 591.121480] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791
[ 591.175511] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603
[ 591.175522] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling.
[ 591.181795] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103
[ 591.181865] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603
[ 591.232780] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 591.232792] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.232840] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 591.232852] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state
[ 591.232854] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 591.232865] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.232981] xhci_hcd 0000:00:14.0: Successful setup address command
[ 591.233001] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000
[ 591.233005] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000
[ 591.233008] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000
[ 591.233010] xhci_hcd 0000:00:14.0: Internal device address = 1
[ 591.244582] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 591.244665] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80
[ 591.244672] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84
[ 591.244674] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587
[ 591.244681] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.245049] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 591.245301] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.245354] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6
[ 591.245380] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.245580] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.245743] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1
[ 591.245769] xhci_hcd 0000:00:14.0: // Ding dong!
[ 591.345699] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling
Best regards,
Eric
next prev parent reply other threads:[~2026-09-11 12:11 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-10 14:47 [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG Eric Lin
2026-09-11 9:53 ` Mathias Nyman
2026-09-11 12:11 ` EricLin [this message]
2026-09-11 13:39 ` Mathias Nyman
2026-09-11 14:48 ` EricLin
2026-09-11 20:21 ` Michal Pecio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260911121107.33832-1-ericlin050914@gmail.com \
--to=ericlin050914@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-usb@vger.kernel.org \
--cc=mathias.nyman@intel.com \
--cc=mathias.nyman@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.