From: Stephen Hemminger <stephen@networkplumber.org>
To: Marat Khalili <qm2k21@gmail.com>
Cc: Konstantin Ananyev <konstantin.ananyev@huawei.com>, dev@dpdk.org
Subject: Re: [PATCH 8/9] bpf: use relaxed stores for callback inuse tracking
Date: Sun, 11 Oct 2026 12:52:56 -0700 [thread overview]
Message-ID: <20261011125256.753e35bd@phoenix.local> (raw)
In-Reply-To: <20261011182158.124246-9-qm2k21@gmail.com>
On Sun, 11 Oct 2026 18:21:56 +0000
Marat Khalili <qm2k21@gmail.com> wrote:
> Direct assignment to an atomic variable defaults to sequentially
> consistent memory order in C11. Since cross-thread memory ordering
> for packet callback execution and unload is already explicitly
> enforced by memory barriers, sequentially consistent stores are
> unnecessary and may emit redundant barrier instructions on weakly
> ordered architectures.
>
> Update bpf_eth_cbi_inuse() and bpf_eth_cbi_unuse() to use
> rte_atomic_store_explicit() with rte_memory_order_relaxed, matching
> the relaxed loads already used in bpf_eth_cbi_wait().
>
> Signed-off-by: Marat Khalili <qm2k21@gmail.com>
> ---
Already covered by smb_mb conversion patch.
If you want, can just make that into one patch which does
the conversion to bool and gets rid of smp_mb.
next prev parent reply other threads:[~2026-10-11 19:53 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-11 18:21 [PATCH 0/9] bpf: clean up and document ethdev callback synchronization Marat Khalili
2026-10-11 18:21 ` [PATCH 1/9] bpf: document packet callback unload sequence Marat Khalili
2026-10-11 18:21 ` [PATCH 2/9] bpf: document ethdev callback threading limitations Marat Khalili
2026-10-11 18:21 ` [PATCH 3/9] bpf: reject Tx callback installation with MT_LOCKFREE Marat Khalili
2026-10-11 18:21 ` [PATCH 4/9] bpf: add callback flag to skip multi-thread check Marat Khalili
2026-10-11 19:48 ` Stephen Hemminger
2026-10-11 20:12 ` Marat Khalili
2026-10-11 18:21 ` [PATCH 5/9] bpf: remove redundant memory barrier on unload Marat Khalili
2026-10-11 19:50 ` Stephen Hemminger
2026-10-11 20:14 ` Marat Khalili
2026-10-11 18:21 ` [PATCH 6/9] bpf: simplify callback inuse tracking to boolean flag Marat Khalili
2026-10-11 19:51 ` Stephen Hemminger
2026-10-11 20:17 ` Marat Khalili
2026-10-11 18:21 ` [PATCH 7/9] bpf: reformat packet callback unload diagram Marat Khalili
2026-10-11 18:21 ` [PATCH 8/9] bpf: use relaxed stores for callback inuse tracking Marat Khalili
2026-10-11 19:52 ` Stephen Hemminger [this message]
2026-10-11 20:24 ` Marat Khalili
2026-10-11 18:21 ` [PATCH 9/9] bpf: make callback handle atomic with relaxed access Marat Khalili
2026-10-11 19:54 ` Stephen Hemminger
2026-10-11 20:31 ` Marat Khalili
2026-10-11 20:29 ` [RFC] bpf: fix callback unload with concurrent Tx burst Stephen Hemminger
2026-10-12 21:09 ` [PATCH v2 0/9] bpf: clean up and document ethdev callback synchronization Marat Khalili
2026-10-12 21:09 ` [PATCH v2 1/9] bpf: document packet callback unload sequence Marat Khalili
2026-10-12 21:09 ` [PATCH v2 2/9] bpf: document ethdev callback threading limitations Marat Khalili
2026-10-12 21:44 ` Stephen Hemminger
2026-10-12 21:09 ` [PATCH v2 3/9] bpf: reject Tx callback installation with MT_LOCKFREE Marat Khalili
2026-10-12 21:09 ` [PATCH v2 4/9] bpf: remove redundant memory barrier on unload Marat Khalili
2026-10-12 21:09 ` [PATCH v2 5/9] bpf: simplify callback inuse tracking to boolean flag Marat Khalili
2026-10-12 21:09 ` [PATCH v2 6/9] bpf: reformat packet callback unload diagram Marat Khalili
2026-10-12 21:09 ` [PATCH v2 7/9] bpf: use relaxed accesses for callback inuse tracking Marat Khalili
2026-10-12 21:09 ` [PATCH v2 8/9] bpf: make callback handle atomic with relaxed access Marat Khalili
2026-10-12 21:09 ` [PATCH v2 9/9] bpf: add callback flag to skip multi-thread check Marat Khalili
2026-10-13 16:55 ` Stephen Hemminger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261011125256.753e35bd@phoenix.local \
--to=stephen@networkplumber.org \
--cc=dev@dpdk.org \
--cc=konstantin.ananyev@huawei.com \
--cc=qm2k21@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.