[PATCH ath-next] wifi: ath9k: release the LED GPIO after ath9k_stop()

[Rosen Penev <rosenp@gmail.com>]

ath9k_deinit_device() frees the LED pin in ath_deinit_leds() before it
unregisters the hw. ath9k_stop() then switches the LED pin back to an
input with ath9k_hw_gpio_request_in(). For a SoC GPIO outside of the
WMAC, ath9k_hw_gpio_request() takes a new descriptor through
gpiod_get_index() at that point, and nothing releases it again. The
next probe fails with "request GPIO12 failed:-16" and every LED update
hits the WARN_ON() in ath9k_hw_set_gpio(). That request also runs
under sc->sc_pcu_lock, while gpiod_get_index() and
gpiod_set_consumer_name() may sleep.

Free the LED pin after ieee80211_unregister_hw() instead. This also
frees the pin when the LED class device could not be registered,
which leaked it before.

Seen on a TP-Link Archer C7 v2 (QCA9558, LED on SoC GPIO 12) when
reloading ath9k.

Fixes: e34f2ff40e03 ("ath9k: bring back direction setting in ath9k_{start_stop}")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
---
 drivers/net/wireless/ath/ath9k/gpio.c | 2 --
 drivers/net/wireless/ath/ath9k/init.c | 5 +++++
 2 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/gpio.c b/drivers/net/wireless/ath/ath9k/gpio.c
index 2dbc7efdd637..d525d8ef9369 100644
--- a/drivers/net/wireless/ath/ath9k/gpio.c
+++ b/drivers/net/wireless/ath/ath9k/gpio.c
@@ -67,8 +67,6 @@ void ath_deinit_leds(struct ath_softc *sc)
 
 	ath_led_brightness(&sc->led_cdev, LED_OFF);
 	led_classdev_unregister(&sc->led_cdev);
-
-	ath9k_hw_gpio_free(sc->sc_ah, sc->sc_ah->led_pin);
 }
 
 void ath_init_leds(struct ath_softc *sc)
diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index a7a11781d83d..f6aa2ec1683c 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -1128,6 +1128,11 @@ void ath9k_deinit_device(struct ath_softc *sc)
 	ath9k_deinit_debug(sc);
 	ath9k_deinit_wow(hw);
 	ieee80211_unregister_hw(hw);
+
+	/* release the LED pin only after ath9k_stop() has configured it */
+	if (sc->sc_ah->led_pin >= 0)
+		ath9k_hw_gpio_free(sc->sc_ah, sc->sc_ah->led_pin);
+
 	ath_rx_cleanup(sc);
 	ath9k_deinit_softc(sc);
 }
-- 
2.56.0