From: Rob Herring <robh@kernel.org>
To: Chancel Liu <chancel.liu@oss.nxp.com>
Cc: krzk+dt@kernel.org, conor+dt@kernel.org, Frank.Li@nxp.com,
s.hauer@pengutronix.de, kernel@pengutronix.de,
festevam@gmail.com, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, imx@lists.linux.dev,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v4 1/4] dt-bindings: connector: Add fsl,aud-io-slot binding
Date: Mon, 16 Nov 2026 10:01:01 -0600 [thread overview]
Message-ID: <20261116160101.GA2015740-robh@kernel.org> (raw)
In-Reply-To: <dd68ae61-9dfd-4138-acf5-b77c63ba0fa3@oss.nxp.com>
On Mon, Nov 16, 2026 at 04:14:26PM +0800, Chancel Liu wrote:
> On 11/13/2026 6:53 AM, Rob Herring wrote:
> > On Thu, Nov 05, 2026 at 03:41:14PM +0900, Chancel Liu wrote:
> >> From: Chancel Liu <chancel.liu@nxp.com>
> >>
> >> The NXP AUD-IO slot represents a physically present I/O connector on
> >> the base board. It acts as a nexus that exposes a constrained set of
> >> I/O resources, such as GPIOs, clocks and interrupts, through fixed
> >> electrical wiring. All actual hardware providers reside on the base
> >> board. The connector node only defines index-based mappings to those
> >> providers.
> >>
> >> This connector type is present on i.MX95 19x19 EVK and i.MX952 EVK,
> >> where it is used to attach the IMX-AUD-IO audio expansion card[1]. The
> >> same add-on board can be reused across different base boards that carry
> >> this connector.
> >>
> >> [1]https://www.nxp.com/part/IMX-AUD-IO
> >
> > That link is pretty much useless. Is there a pinout definition
> > somewhere?
> >
>
> The detailed user manual (UM12022) is listed as official documentation:
> https://docs.nxp.com/bundle/UM12022/page/topics/pcie_interface1.html
> But it is behind an NXP login.
>
> The brief pinout table looks like this:
>
> Pin Signal Dir
> ---- ------------------ ---
> A11 PCI_AUD_RST_B In (GPIO)
> A12 AUD_CARD_DET Out (INT)
> A21 AUD_SPI7_SCLK In
> A22 AUD_SPI7_SS0 In
> A25 AUD_SPI7_MOSI In
> A26 AUD_SPI7_MISO Out
> A29 AUD_SPI7_SCLK In
> A30 AUD_SPI7_SS0 In
> A32 AUD_SPI7_MISO Out
> A33 AUD_SPI7_MOSI In
> B5 I2C6_SCL_1V8 In
> B6 I2C6_SDA_1V8 I/O
> B10 AUD_SLOT_PWR_SYNC In (GPIO)
> B11 AUD_SLOT_PWRDN In (GPIO)
> B12 AUD_SLOT_MCLK In (CLK)
> B14 AUD_SLOT_INT_B Out (INT)
> B15 AUD_SLOT_INT_B Out
> B17 AUD_SLOT_INT_B Out
> B23 SAI2_RXFS Out
> B24 SAI2_RXC Out
> B27 SAI2_TXD1 In
> B28 SAI2_TXD2 In
> B30 SAI2_TXD3 In
> B31 SAI2_RXD1 Out
> A2, A3, B1, B2, B3 VCC_EXT_12V0
> B8, A9, A10 VCC_EXT_3V3
>
> > Looking at the overlay, this looks incomplete. It looks like there's I2C
> > thru the connector for example. There's also power rails.
> >
> > The idea with connectors is that overlays apply to the connector node
> > and nothing else.
>
> For this patch set, I2C, I2S and regulators are
> provided by the base boards using a common set of labels:
>
> aud_io_i2c
> aud_io_cpu
> aud_io_reg_1v8
> aud_io_reg_3v3
> aud_io_reg_5v
>
> The common add-on board overlay references these labels directly. This
> allows the same overlay to be used with both base boards. But the
> overlay still depends on nodes outside the connector.
Using labels is a solution, but not one I particularly like because that
makes labels an ABI yet we don't document them.
> > I2C we've kind of figured out with something like this:
> >
> > connector {
> > i2c-parent = <&i2c>;
> > i2c {
> > ...
> > };
> > };
> >
>
> I will rework the I2C part using this model.
>
> > Regulators is still open issue though.
> >
> > Rob
>
> Good to know this is being discussed. Is there a mailing-list thread or
> patch series I can follow?
Search lore. There's been a number of connector series over the years.
gpio-map, clock-map, pwm-map have all come out of those discussions.
Rob
next prev parent reply other threads:[~2026-11-16 16:01 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-05 6:41 [PATCH v4 0/4] arm64: dts: freescale: Add IMX-AUD-IO add-on board support Chancel Liu
2026-11-05 6:41 ` [PATCH v4 1/4] dt-bindings: connector: Add fsl,aud-io-slot binding Chancel Liu
2026-11-05 6:59 ` sashiko-bot
2026-11-12 22:53 ` Rob Herring
2026-11-16 8:14 ` Chancel Liu
2026-11-16 16:01 ` Rob Herring [this message]
2026-11-05 6:41 ` [PATCH v4 2/4] arm64: dts: freescale: imx95-19x19-evk: Add IMX-AUD-IO board support Chancel Liu
2026-11-05 6:41 ` [PATCH v4 3/4] arm64: dts: freescale: imx952-evk: " Chancel Liu
2026-11-05 6:41 ` [PATCH v4 4/4] arm64: dts: freescale: Add common DTS overlay for IMX-AUD-IO add-on board Chancel Liu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261116160101.GA2015740-robh@kernel.org \
--to=robh@kernel.org \
--cc=Frank.Li@nxp.com \
--cc=chancel.liu@oss.nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.