From: Jayesh Agarwal <agarwaljayesh03@gmail.com>
To: qemu-devel@nongnu.org
Cc: peter.maydell@linaro.org, philmd@oss.qualcomm.com,
qemu-arm@nongnu.org, s23adhik@csclub.uwaterloo.ca,
Jayesh Agarwal <agarwaljayesh03@gmail.com>
Subject: [PATCH] hw/arm/bcm2838: Route system timer interrupts to GIC
Date: Wed, 18 Nov 2026 01:02:05 +0530 [thread overview]
Message-ID: <20261117193205.8236-1-agarwaljayesh03@gmail.com> (raw)
The system timer interrupts are only routed to the legacy interrupt
controller and not to the GIC, so a guest using the GIC (software that
relies on the system timer interrupts through the GIC, such as bare
metal programs or hobby kernels) never receives them.
A qemu_irq connection follows one output, one input. So also wiring the
timer to the GIC would replace its connection to the legacy controller.
Add a splitter per system-timer interrupt line so that each interrupt
reaches both the legacy controller (output 0 of the splitters) and the
GIC (output 1 of the splitters). The timer channel n goes to GIC SPI
64+n, so channels 0-3 go to SPIs 64-67.
Testing:
The raspi4b machine started in the qtest mode:
qemu-system-aarch64 -M raspi4b -display none -accel qtest -qtest stdio
Ran following commands:
irq_intercept_in /machine/soc/peripherals
readl 0xfe003004
writel 0xfe00300c 1000
writel 0xfe003010 2000
writel 0xfe003014 3000
writel 0xfe003018 4000
clock_step 5000000
readl 0xfe003000
Before the fix:
clock_step 5000000
OK 5000000
readl 0xfe003000
OK 0x000000000000000f
The alarm fires correctly (status flag outputs 0xf), but no IRQ raise
64-67 reaches the GIC.
After the fix:
clock_step 5000000
IRQ raise 64
IRQ raise 65
IRQ raise 66
IRQ raise 67
OK 5000000
readl 0xfe003000
OK 0x000000000000000f
The alarm fires, and all the four channels reached GIC lines 64-67.
Reported-by: Sourojeet Adhikari <s23adhik@csclub.uwaterloo.ca>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jayesh Agarwal <agarwaljayesh03@gmail.com>
---
This was picked up from Sourojeet's earlier patch, here is the link:
https://lore.kernel.org/qemu-devel/3cca4eb3-09d1-4467-81fd-27a5bfe19a3e@csclub.uwaterloo.ca/
hw/arm/bcm2835_peripherals.c | 33 ++++++++++++++++++----------
hw/arm/bcm2838.c | 7 ++++++
include/hw/arm/bcm2835_peripherals.h | 1 +
include/hw/arm/bcm2838_peripherals.h | 4 ++++
4 files changed, 33 insertions(+), 12 deletions(-)
diff --git a/hw/arm/bcm2835_peripherals.c b/hw/arm/bcm2835_peripherals.c
index 558c180df9..f619beba33 100644
--- a/hw/arm/bcm2835_peripherals.c
+++ b/hw/arm/bcm2835_peripherals.c
@@ -95,6 +95,14 @@ static void raspi_peripherals_base_init(Object *obj)
/* SYS Timer */
object_initialize_child(obj, "systimer", &s->systmr,
TYPE_BCM2835_SYSTIMER);
+ /*
+ * One splitter per system-timer interrupt line so that each interrupt
+ * reaches both the legacy controller and the GIC.
+ */
+ for (int n = 0; n < BCM2835_SYSTIMER_COUNT; n++) {
+ object_initialize_child(obj, "systmr-irq-splitter[*]",
+ &s->systmr_irq_splitter[n], TYPE_SPLIT_IRQ);
+ }
/* UART0 */
object_initialize_child(obj, "uart0", &s->uart0, TYPE_PL011);
@@ -302,18 +310,19 @@ void bcm_soc_peripherals_common_realize(DeviceState *dev, Error **errp)
}
memory_region_add_subregion(&s->peri_mr, ST_OFFSET,
sysbus_mmio_get_region(SYS_BUS_DEVICE(&s->systmr), 0));
- sysbus_connect_irq(SYS_BUS_DEVICE(&s->systmr), 0,
- qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
- INTERRUPT_TIMER0));
- sysbus_connect_irq(SYS_BUS_DEVICE(&s->systmr), 1,
- qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
- INTERRUPT_TIMER1));
- sysbus_connect_irq(SYS_BUS_DEVICE(&s->systmr), 2,
- qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
- INTERRUPT_TIMER2));
- sysbus_connect_irq(SYS_BUS_DEVICE(&s->systmr), 3,
- qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
- INTERRUPT_TIMER3));
+ for (n = 0; n < BCM2835_SYSTIMER_COUNT; n++) {
+ qdev_prop_set_uint32(DEVICE(&s->systmr_irq_splitter[n]),
+ "num-lines", 2);
+ if (!qdev_realize(DEVICE(&s->systmr_irq_splitter[n]), NULL, errp)) {
+ return;
+ }
+ sysbus_connect_irq(SYS_BUS_DEVICE(&s->systmr), n,
+ qdev_get_gpio_in(DEVICE(&s->systmr_irq_splitter[n]), 0));
+ qdev_connect_gpio_out(DEVICE(&s->systmr_irq_splitter[n]), 0,
+ qdev_get_gpio_in_named(DEVICE(&s->ic),
+ BCM2835_IC_GPU_IRQ,
+ INTERRUPT_TIMER0 + n));
+ }
/* UART0 */
qdev_prop_set_chr(DEVICE(&s->uart0), "chardev", serial_hd(0));
diff --git a/hw/arm/bcm2838.c b/hw/arm/bcm2838.c
index 650b1fe8f4..d151c50f1e 100644
--- a/hw/arm/bcm2838.c
+++ b/hw/arm/bcm2838.c
@@ -188,6 +188,13 @@ static void bcm2838_realize(DeviceState *dev, Error **errp)
qdev_connect_gpio_out(DEVICE(&ps_base->orgated_i2c_irq_splitter), 1,
qdev_get_gpio_in(gicdev, GIC_SPI_INTERRUPT_I2C));
+ /* Connect the system timer interrupts to the interrupt controller */
+ for (int n = 0; n < BCM2835_SYSTIMER_COUNT; n++) {
+ int int_n = GIC_SPI_INTERRUPT_SYS_TIMER0 + n;
+ qdev_connect_gpio_out(DEVICE(&ps_base->systmr_irq_splitter[n]), 1,
+ qdev_get_gpio_in(gicdev, int_n));
+ }
+
/* Connect VC mailbox to the interrupt controller */
sysbus_connect_irq(SYS_BUS_DEVICE(&ps_base->mboxes), 0,
qdev_get_gpio_in(gicdev, GIC_SPI_INTERRUPT_MBOX));
diff --git a/include/hw/arm/bcm2835_peripherals.h b/include/hw/arm/bcm2835_peripherals.h
index 4f356f4643..bd41e0de92 100644
--- a/include/hw/arm/bcm2835_peripherals.h
+++ b/include/hw/arm/bcm2835_peripherals.h
@@ -54,6 +54,7 @@ struct BCMSocPeripheralBaseState {
qemu_irq irq, fiq;
BCM2835SystemTimerState systmr;
+ SplitIRQ systmr_irq_splitter[BCM2835_SYSTIMER_COUNT];
BCM2835MphiState mphi;
UnimplementedDeviceState txp;
UnimplementedDeviceState armtmr;
diff --git a/include/hw/arm/bcm2838_peripherals.h b/include/hw/arm/bcm2838_peripherals.h
index 60bfacdce4..af2d3b2030 100644
--- a/include/hw/arm/bcm2838_peripherals.h
+++ b/include/hw/arm/bcm2838_peripherals.h
@@ -20,6 +20,10 @@
/* SPI */
#define GIC_SPI_INTERRUPT_MBOX 33
#define GIC_SPI_INTERRUPT_MPHI 40
+#define GIC_SPI_INTERRUPT_SYS_TIMER0 64
+#define GIC_SPI_INTERRUPT_SYS_TIMER1 65
+#define GIC_SPI_INTERRUPT_SYS_TIMER2 66
+#define GIC_SPI_INTERRUPT_SYS_TIMER3 67
#define GIC_SPI_INTERRUPT_DWC2 73
#define GIC_SPI_INTERRUPT_DMA_0 80
#define GIC_SPI_INTERRUPT_DMA_6 86
--
2.43.0
reply other threads:[~2026-11-17 19:32 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261117193205.8236-1-agarwaljayesh03@gmail.com \
--to=agarwaljayesh03@gmail.com \
--cc=peter.maydell@linaro.org \
--cc=philmd@oss.qualcomm.com \
--cc=qemu-arm@nongnu.org \
--cc=qemu-devel@nongnu.org \
--cc=s23adhik@csclub.uwaterloo.ca \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.