From: pjh456 <pengjunhao409@gmail.com>
To: Neil Armstrong <neil.armstrong@linaro.org>
Cc: dri-devel@lists.freedesktop.org,
Jessica Zhang <jesszhan0024@gmail.com>,
Maxime Ripard <mripard@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Subject: [PATCH v3 0/3] drm/panel: ilitek-ili9881c: add Industio Purple Pi OH panel
Date: Wed, 18 Nov 2026 17:59:02 +0800 [thread overview]
Message-ID: <20261118095905.127658-1-pengjunhao409@gmail.com> (raw)
This series adds support for the 7-inch 800x1280 ILI9881C panel used on
the Industio Purple Pi OH (RK3566).
Patch 1 adds the Shenzhen Industio Technology vendor prefix. Patch 2
adds a board-specific panel compatible with ilitek,ili9881c as the
fallback; the module is marked ZC-700010BH and has a 94x151 mm active
area. The vendor device tree only describes it as a generic
"simple-panel-dsi", so no panel-vendor compatible is known.
Patch 3 adds a dedicated driver entry with the vendor initialisation
sequence. The existing am8001280g entry (another 7-inch 800x1280
ILI9881C panel) was tested on this hardware and only lights the
backlight without a picture, so the vendor sequence is required.
The panel is reset through GPIO0_D6 and its backlight is driven by PWM4.
On hardware, the panel probes as DSI-1 94x151, modetest reports the
expected mode, and the geometry test pattern is correct.
The board DTS that uses this compatible is part of a separate Purple Pi
OH board series.
AI assistance: parts of this series were drafted with AI coding
assistants, using the vendor device tree as input. All changes were
reviewed, built and tested on hardware by the submitter, who takes full
responsibility for the content.
v3: resend as pjh456 <pengjunhao409@gmail.com>. The v2 posting used the
147148383@qq.com address through Gmail's SMTP, which is not
DMARC-aligned, so it never reached the lists.
v2: add the vendor prefix to this series, drop the redundant
width-mm/height-mm properties (the driver supplies the panel
geometry), and remove the non-standard Assisted-by tags from the
commit messages.
pjh456 (3):
dt-bindings: vendor-prefixes: add Shenzhen Industio Technology
dt-bindings: display: panel: ilitek,ili9881c: add Industio Purple Pi
OH panel
drm/panel: ilitek-ili9881c: add Industio Purple Pi OH panel
.../display/panel/ilitek,ili9881c.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
drivers/gpu/drm/panel/panel-ilitek-ili9881c.c | 222 ++++++++++++++++++
3 files changed, 225 insertions(+)
base-commit: 7e1392a42ea288d70a266f6553fe06f57f8647ea
--
2.56.1
next reply other threads:[~2026-11-18 13:47 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-18 9:59 pjh456 [this message]
2026-11-18 9:59 ` [PATCH v3 1/3] dt-bindings: vendor-prefixes: add Shenzhen Industio Technology pjh456
2026-11-18 14:33 ` Krzysztof Kozlowski
2026-11-18 9:59 ` [PATCH v3 2/3] dt-bindings: display: panel: ilitek, ili9881c: add Industio Purple Pi OH panel pjh456
2026-11-18 17:43 ` Conor Dooley
2026-11-18 17:45 ` Conor Dooley
2026-11-18 9:59 ` [PATCH v3 3/3] drm/panel: ilitek-ili9881c: " pjh456
2026-11-18 11:10 ` [PATCH v3 0/3] " Conor.Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261118095905.127658-1-pengjunhao409@gmail.com \
--to=pengjunhao409@gmail.com \
--cc=conor+dt@kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=jesszhan0024@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.