From: Rosen Penev <rosenp@gmail.com>
To: "Florian Fainelli" <florian.fainelli@broadcom.com>,
"Hauke Mehrtens" <hauke@hauke-m.de>,
"Rafał Miłecki" <zajec5@gmail.com>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>
Cc: "Broadcom internal kernel review list"
<bcm-kernel-feedback-list@broadcom.com>,
"Rafał Miłecki" <rafal@milecki.pl>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Subject: [PATCH v3 00/22] ARM: dts: BCM5301X: describe switches and use gmac2 as the CPU port
Date: Fri, 20 Nov 2026 16:25:40 -0800 [thread overview]
Message-ID: <20261121002603.25254-1-rosenp@gmail.com> (raw)
This series describes the switch on fourteen more BCM5301X boards, makes
switch port 8 / gmac2 the CPU port on the single-CPU-port boards whose
MAC address can be assigned to gmac2, and disables the GMACs that a
board does not use.
Patches 1-8 describe the switch ports on the RT-AC56U, RT-AC68U, RT-N18U,
R7000, EA6300 and Phicomm K3. They also set the WAN MAC address from
nvram, so userspace doesn't have to. The EA6300 and K3 get an nvram node
for that. The port mappings come from OpenWrt.
Patches 9-19 do the same for the R6300 v2, EA6500 v2, R8500, WZR-900DHP,
WZR-1750DHP, WXR-1900DHP, Archer C5 v2 and Archer C9 v1. The R6300 v2,
EA6500 v2 and R8500 get an nvram node and use port 8 (gmac2) with the
MAC address from et0macaddr (et2macaddr on the R8500). The Buffalo and
TP-Link boards have no MAC address described, so they use port 5
(gmac0), which gets et0macaddr through the SPROM fallback.
Patch 20 is a fix: on the DIR-885L the nvram MAC address has been on
gmac0 since port 8 became its only CPU port. It moves it to gmac2.
Patch 21 moves the CPU port from port 5 (gmac0), or port 7 (gmac1) on
the RT-AC87U, to port 8 (gmac2) on the remaining single-CPU-port boards.
Port 8 is the switch's IMP port, and gmac2 is present on all Northstar
SoCs. The nvram MAC address moves to gmac2 as well, and the R6250 gets
an nvram node for it. Boards whose MAC address only comes from the SPROM
fallback (et0macaddr for gmac0) stay on port 5, since gmac2 would read
et2macaddr instead.
Patch 22 disables all GMACs in bcm-ns.dtsi and enables only the ones each
board uses. Boards with a switch node enable the GMACs behind their CPU
ports. Boards without one keep gmac0-gmac2, because nothing configures
their switch and which GMAC carries traffic depends on the bootloader.
Boards with several CPU ports (RT-AC3100, RT-AC3200, RT-AC5300,
RT-AC88U, WXR-1750DHP) keep them all.
Compile-tested only. Every patch builds, and dtbs_check output for all
BCM5301X boards is unchanged by the series.
An AI coding assistant (Claude Code, Claude Opus 5.5) was used to review
the series, write patches 9-21 and parts of 22, check the board
descriptions against OpenWrt, and draft the commit messages and this
cover letter.
Changes in v3:
- R6250: set status in the existing &gmac2 node instead of adding a
second one.
- DWL-8610AP: enable gmac2 too, like the other boards without a switch
node.
- Link to v2: https://lore.kernel.org/linux-devicetree/20261119085452.75708-1-rosenp@gmail.com/
Changes in v2:
- Squash the per-board port 8/gmac2 conversions (AC87U, SR400AC, Luxul,
R6250, Meraki MR26/MR32) into one patch (Florian). The DIR-885L patch
stays separate since it carries a Fixes: tag.
- R6250: add an nvram node and take the gmac2 MAC address from
et0macaddr, so it doesn't get a random one.
- Keep Buffalo WZR-600DHP2/WZR-1166DHP/WZR-1166DHP2 and BCM953012ER on
port 5/gmac0: they have no MAC address in DT and would get a random
one from the empty et2macaddr SPROM fallback.
- Boards without a switch node keep gmac0, gmac1 and gmac2 enabled
instead of only gmac2, since their switch is left as the bootloader
configured it.
- Describe the switch on the R6300 v2, EA6500 v2, R8500, WZR-900DHP,
WZR-1750DHP, WXR-1900DHP, Archer C5 v2 and Archer C9 v1 (new patches
9-19), taking the port mappings and MAC address sources from OpenWrt.
- Link to v1: https://lore.kernel.org/linux-devicetree/20261118054758.132233-1-rosenp@gmail.com/
Rosen Penev (22):
ARM: dts: BCM5301X: AC56U: specify switch
ARM: dts: BCM5301X: AC68U: specify switch
ARM: dts: BCM5301X: N18U: specify switch
ARM: dts: BCM5301X: R7000: specify switch
ARM: dts: BCM5301X: EA6300: set gmac2 MAC address from nvram
ARM: dts: BCM5301X: EA6300: specify switch
ARM: dts: BCM5301X: phicomm-k3: add nvram node
ARM: dts: BCM5301X: phicomm-k3: specify switch
ARM: dts: BCM5301X: R6300 v2: add nvram node
ARM: dts: BCM5301X: R6300 v2: specify switch
ARM: dts: BCM5301X: EA6500 v2: add nvram node
ARM: dts: BCM5301X: EA6500 v2: specify switch
ARM: dts: BCM5301X: R8500: add nvram node
ARM: dts: BCM5301X: R8500: specify switch
ARM: dts: BCM5301X: WZR-900DHP: specify switch
ARM: dts: BCM5301X: WZR-1750DHP: specify switch
ARM: dts: BCM5301X: WXR-1900DHP: specify switch
ARM: dts: BCM5301X: Archer C5 v2: specify switch
ARM: dts: BCM5301X: Archer C9 v1: specify switch
ARM: dts: BCM5301X: DIR-885L: use gmac2
ARM: dts: BCM5301X: use gmac2 as the CPU port
ARM: dts: BCM5301X: enable GMACs in boards that use them
arch/arm/boot/dts/broadcom/bcm-ns.dtsi | 8 +++
.../dts/broadcom/bcm4708-asus-rt-ac56u.dts | 39 ++++++++++++++
.../dts/broadcom/bcm4708-asus-rt-ac68u.dts | 39 ++++++++++++++
.../broadcom/bcm4708-buffalo-wxr-1750dhp.dts | 12 +++++
.../bcm4708-buffalo-wzr-1166dhp-common.dtsi | 4 ++
.../broadcom/bcm4708-buffalo-wzr-1750dhp.dts | 42 +++++++++++++++
.../broadcom/bcm4708-linksys-ea6300-v1.dts | 48 +++++++++++++++++
.../broadcom/bcm4708-linksys-ea6500-v2.dts | 53 +++++++++++++++++++
.../dts/broadcom/bcm4708-luxul-xap-1510.dts | 8 +--
.../dts/broadcom/bcm4708-luxul-xwc-1000.dts | 8 +--
.../dts/broadcom/bcm4708-netgear-r6250.dts | 20 ++++++-
.../dts/broadcom/bcm4708-netgear-r6300-v2.dts | 53 +++++++++++++++++++
.../dts/broadcom/bcm4708-smartrg-sr400ac.dts | 10 ++--
.../dts/broadcom/bcm47081-asus-rt-n18u.dts | 39 ++++++++++++++
.../broadcom/bcm47081-buffalo-wzr-600dhp2.dts | 4 ++
.../broadcom/bcm47081-buffalo-wzr-900dhp.dts | 42 +++++++++++++++
.../dts/broadcom/bcm47081-luxul-xap-1410.dts | 8 +--
.../dts/broadcom/bcm47081-luxul-xwr-1200.dts | 8 +--
.../broadcom/bcm47081-tplink-archer-c5-v2.dts | 42 +++++++++++++++
.../dts/broadcom/bcm4709-asus-rt-ac3200.dts | 6 +++
.../dts/broadcom/bcm4709-asus-rt-ac87u.dts | 8 ++-
.../broadcom/bcm4709-buffalo-wxr-1900dhp.dts | 42 +++++++++++++++
.../dts/broadcom/bcm4709-linksys-ea9200.dts | 2 +
.../dts/broadcom/bcm4709-netgear-r7000.dts | 39 ++++++++++++++
.../dts/broadcom/bcm4709-netgear-r8000.dts | 4 ++
.../broadcom/bcm4709-tplink-archer-c9-v1.dts | 42 +++++++++++++++
.../dts/broadcom/bcm47094-asus-rt-ac3100.dts | 6 +++
.../dts/broadcom/bcm47094-asus-rt-ac5300.dts | 6 +++
.../dts/broadcom/bcm47094-asus-rt-ac88u.dts | 8 +--
.../dts/broadcom/bcm47094-dlink-dir-885l.dts | 4 +-
.../dts/broadcom/bcm47094-dlink-dir-890l.dts | 2 +
.../broadcom/bcm47094-linksys-panamera.dts | 4 ++
.../dts/broadcom/bcm47094-luxul-abr-4500.dts | 8 +--
.../dts/broadcom/bcm47094-luxul-xap-1610.dts | 8 +--
.../dts/broadcom/bcm47094-luxul-xbr-4500.dts | 8 +--
.../dts/broadcom/bcm47094-luxul-xwc-2000.dts | 8 +--
.../dts/broadcom/bcm47094-luxul-xwr-3100.dts | 8 +--
.../broadcom/bcm47094-luxul-xwr-3150-v1.dts | 8 +--
.../dts/broadcom/bcm47094-netgear-r8500.dts | 53 +++++++++++++++++++
.../boot/dts/broadcom/bcm47094-phicomm-k3.dts | 53 +++++++++++++++++++
.../dts/broadcom/bcm53015-meraki-mr26.dts | 21 ++------
.../broadcom/bcm53016-dlink-dwl-8610ap.dts | 8 +++
.../dts/broadcom/bcm53016-meraki-mr32.dts | 23 ++------
arch/arm/boot/dts/broadcom/bcm94708.dts | 12 +++++
arch/arm/boot/dts/broadcom/bcm94709.dts | 12 +++++
arch/arm/boot/dts/broadcom/bcm953012er.dts | 4 ++
arch/arm/boot/dts/broadcom/bcm953012hr.dts | 12 +++++
arch/arm/boot/dts/broadcom/bcm953012k.dts | 12 +++++
48 files changed, 834 insertions(+), 84 deletions(-)
base-commit: 909ef7a9a30fa139e69e555e3606680f5cca7726
--
2.56.1
next reply other threads:[~2026-11-21 0:26 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-21 0:25 Rosen Penev [this message]
2026-11-21 0:25 ` [PATCH v3 01/22] ARM: dts: BCM5301X: AC56U: specify switch Rosen Penev
2026-11-21 0:25 ` [PATCH v3 02/22] ARM: dts: BCM5301X: AC68U: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 03/22] ARM: dts: BCM5301X: N18U: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 04/22] ARM: dts: BCM5301X: R7000: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 05/22] ARM: dts: BCM5301X: EA6300: set gmac2 MAC address from nvram Rosen Penev
2026-11-21 0:25 ` [PATCH v3 06/22] ARM: dts: BCM5301X: EA6300: specify switch Rosen Penev
2026-11-21 0:25 ` [PATCH v3 07/22] ARM: dts: BCM5301X: phicomm-k3: add nvram node Rosen Penev
2026-11-21 0:25 ` [PATCH v3 08/22] ARM: dts: BCM5301X: phicomm-k3: specify switch Rosen Penev
2026-11-21 0:25 ` [PATCH v3 09/22] ARM: dts: BCM5301X: R6300 v2: add nvram node Rosen Penev
2026-11-21 0:25 ` [PATCH v3 10/22] ARM: dts: BCM5301X: R6300 v2: specify switch Rosen Penev
2026-11-21 0:25 ` [PATCH v3 11/22] ARM: dts: BCM5301X: EA6500 v2: add nvram node Rosen Penev
2026-11-21 0:25 ` [PATCH v3 12/22] ARM: dts: BCM5301X: EA6500 v2: specify switch Rosen Penev
2026-11-21 0:25 ` [PATCH v3 13/22] ARM: dts: BCM5301X: R8500: add nvram node Rosen Penev
2026-11-21 0:25 ` [PATCH v3 14/22] ARM: dts: BCM5301X: R8500: specify switch Rosen Penev
2026-11-21 0:25 ` [PATCH v3 15/22] ARM: dts: BCM5301X: WZR-900DHP: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 16/22] ARM: dts: BCM5301X: WZR-1750DHP: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 17/22] ARM: dts: BCM5301X: WXR-1900DHP: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 18/22] ARM: dts: BCM5301X: Archer C5 v2: " Rosen Penev
2026-11-21 0:25 ` [PATCH v3 19/22] ARM: dts: BCM5301X: Archer C9 v1: " Rosen Penev
2026-11-21 0:26 ` [PATCH v3 20/22] ARM: dts: BCM5301X: DIR-885L: use gmac2 Rosen Penev
2026-11-21 0:26 ` [PATCH v3 21/22] ARM: dts: BCM5301X: use gmac2 as the CPU port Rosen Penev
2026-11-21 0:26 ` [PATCH v3 22/22] ARM: dts: BCM5301X: enable GMACs in boards that use them Rosen Penev
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261121002603.25254-1-rosenp@gmail.com \
--to=rosenp@gmail.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=florian.fainelli@broadcom.com \
--cc=hauke@hauke-m.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=rafal@milecki.pl \
--cc=robh@kernel.org \
--cc=zajec5@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.