From: Jay Vosburgh <jay.vosburgh@canonical.com>
To: LIU Yulong <i@liuyulong.me>
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
Veaceslav Falico <vfalico@gmail.com>,
Andy Gospodarek <andy@greyhouse.net>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>
Subject: Re: [PATCH] net: bonding: alb disable balance for IPv6 multicast related mac
Date: Tue, 27 Oct 2020 20:53:53 -0700 [thread overview]
Message-ID: <22348.1603857233@famine> (raw)
In-Reply-To: <1603850163-4563-1-git-send-email-i@liuyulong.me>
LIU Yulong <i@liuyulong.me> wrote:
>According to the RFC 2464 [1] the prefix "33:33:xx:xx:xx:xx" is defined to
>construct the multicast destination MAC address for IPv6 multicast traffic.
>The NDP (Neighbor Discovery Protocol for IPv6)[2] will comply with such
>rule. The work steps [6] are:
> *) Let's assume a destination address of 2001:db8:1:1::1.
> *) This is mapped into the "Solicited Node Multicast Address" (SNMA)
> format of ff02::1:ffXX:XXXX.
> *) The XX:XXXX represent the last 24 bits of the SNMA, and are derived
> directly from the last 24 bits of the destination address.
> *) Resulting in a SNMA ff02::1:ff00:0001, or ff02::1:ff00:1.
> *) This, being a multicast address, can be mapped to a multicast MAC
> address, using the format 33-33-XX-XX-XX-XX
> *) Resulting in 33-33-ff-00-00-01.
> *) This is a MAC address that is only being listened for by nodes
> sharing the same last 24 bits.
> *) In other words, while there is a chance for a "address collision",
> it is a vast improvement over ARP's guaranteed "collision".
>Kernel related code can be found at [3][4][5].
>
>The current bond alb has some leaks of such MAC ranges which will cause
>the physical world failed to determain the back tunnel of the reply
>packet during the response in a Spine-and-Leaf data center architecture.
>The basic topology looks like this:
>
> +-------------+
> | |
> +---| Border Leaf |-----+
> | | | |
> | +-------------+ |
> | |
> | tunnel-1 | tunnel-2
> | |
> | |
>+---+----+ +------+-+
>| | | |
>| Leaf1 +--X-X-X-X--+ Leaf2 | tunnel-3 will be checked to prevent loop
>| | tunnel-3 | |
>+--------+ +-+------+
> | |
> | |
> | |
> | |
> | |
> | |
> +----+ +----+
> +--+nic1+---+nic2+---+
> | +----+ +----+ |
> | bond6 |
> | |
> | HOST |
> +--------------------+
This description is, overall, very comprehensive, and I believe
I generally understand what issue you're fixing (which seems to be a
complicated means to cause MAC flapping), although I'm unclear on a few
details, below.
However, if you could make the ASCII art smaller I think that
would be better.
>When nic1 is sending the normal IPv6 traffic to the gateway in Border leaf,
>the nic2 (slave) will send the NS packet out periodically, automatically
>and implicitly as well. This is an example packet sending from the slave
>nic2 which will broke the traffic.
With this patch applied, what would happen if nic2 sends the
normal IPv6 traffic from the source MAC in question (because it is
tx-balanced there), and the Neighbor Solicitation multicast then goes
out via nic1?
> ac:1f:6b:90:5c:eb > 33:33:ff:00:00:01, ethertype 802.1Q (0x8100),
> length 90: vlan 205, p 0, ethertype IPv6, (hlim 255,
> next-header ICMPv6 (58) payload length: 32)
> fe80::f816:3eff:feba:2d8c > ff02::1:ff00:1:
> [icmp6 sum ok] ICMP6, neighbor solicitation, length 32,
> who has 240e:980:2f00:4000::1
> source link-address option (1), length 8 (1): fa:16:3e:ba:2d:8c
> 0x0000: fa16 3eba 2d8c
> 0x0000: 3333 ff00 0001 ac1f 6b90 5ceb 8100 00cd
> 0x0010: 86dd 6000 0000 0020 3aff fe80 0000 0000
> 0x0020: 0000 f816 3eff feba 2d8c ff02 0000 0000
> 0x0030: 0000 0000 0001 ff00 0001 8700 14d3 0000
> 0x0040: 0000 240e 0980 2f00 4000 0000 0000 0000
> 0x0050: 0001 0101 fa16 3eba 2d8c
And perhaps trim out the hex dump here.
>MAC "fa:16:3e:ba:2d:8c" was first learnt at Leaf1 based on the underlay
>mechanism(BGP EVPN). When this example packet was sent to Border leaf and
>replied with dst_mac "fa:16:3e:ba:2d:8c", Leaf2 will try to send packet
>back to tunnel-3 at this point dropping happens because of the loop
>defense. All the original normal IPv6 traffic will be lead to the tunnel-2
>and then drop. Link is broken now.
Where does MAC fa:16:3e:ba:2d:8c come from? Is this the MAC
address of the bond itself?
Assuming that "learnt at Leaf1" means that Leaf1 knows to
forward it to bond6:nic1, why does the loop defense drop the packet if
Leaf1 is on the forwarding path?
>This patch addresses such issue by check the entire MAC range definde by
>the RFC 2464. Adding a new helper method to check the first two octets
>are the value 3333. If the dest mac is matched, no balance will be
>enabled.
>
>[1] https://tools.ietf.org/html/rfc2464#section-7
>[2] https://tools.ietf.org/html/rfc4861
>[3] linux.git/tree/include/net/if_inet6.h#n209-n221
>[4] linux.git/tree/net/ipv6/ndisc.c#n291
>[5] linux.git/tree/net/ipv6/ndisc.c#n346-n348
>[6] https://en.citizendium.org/wiki/Neighbor_Discovery
>
>Signed-off-by: LIU Yulong <i@liuyulong.me>
>---
> drivers/net/bonding/bond_alb.c | 10 ++++------
> include/linux/etherdevice.h | 12 ++++++++++++
> 2 files changed, 16 insertions(+), 6 deletions(-)
>
>diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c
>index 095ea51..a4a30bd 100644
>--- a/drivers/net/bonding/bond_alb.c
>+++ b/drivers/net/bonding/bond_alb.c
>@@ -24,9 +24,6 @@
> #include <net/bonding.h>
> #include <net/bond_alb.h>
>
>-static const u8 mac_v6_allmcast[ETH_ALEN + 2] __long_aligned = {
>- 0x33, 0x33, 0x00, 0x00, 0x00, 0x01
>-};
> static const int alb_delta_in_ticks = HZ / ALB_TIMER_TICKS_PER_SEC;
>
> #pragma pack(1)
>@@ -1422,10 +1419,11 @@ struct slave *bond_xmit_alb_slave_get(struct bonding *bond,
> break;
> }
>
>- /* IPv6 uses all-nodes multicast as an equivalent to
>- * broadcasts in IPv4.
>+ /* IPv6 multicast destination should disable the tx-balance since
>+ * the pyhsical world may get into a mass status which will lead
>+ * to the IPv6 traffic broken.
I think this comment can be simplified to simply say that IPv6
multicast destinations should not be tx-balanced, which I suspect is the
real purpose.
> */
>- if (ether_addr_equal_64bits(eth_data->h_dest, mac_v6_allmcast)) {
>+ if (is_ipv6_multicast_ether_addr(eth_data->h_dest)) {
> do_tx_balance = false;
> break;
> }
>diff --git a/include/linux/etherdevice.h b/include/linux/etherdevice.h
>index 2e5debc..c6101ab 100644
>--- a/include/linux/etherdevice.h
>+++ b/include/linux/etherdevice.h
>@@ -178,6 +178,18 @@ static inline bool is_unicast_ether_addr(const u8 *addr)
> }
>
> /**
>+ * is_ipv6_multicast_ether_addr - Determine if the Ethernet address is for
>+ * IPv6 multicast (rfc2464).
>+ * @addr: Pointer to a six-byte array containing the Ethernet address
>+ *
>+ * Return true if the address is a multicast for IPv6.
>+ */
>+static inline bool is_ipv6_multicast_ether_addr(const u8 *addr)
>+{
>+ return (addr[0] & addr[1]) == 0x33;
>+}
I don't think this does what is intended. It will return true
for a MAC that starts with any two values whose bitwise AND is 0x33,
e.g., 0x73 0x3b. For IPv6 multicast, the first two octets of the MAC
must be exactly 0x33 0x33.
-J
>+
>+/**
> * is_valid_ether_addr - Determine if the given Ethernet address is valid
> * @addr: Pointer to a six-byte array containing the Ethernet address
> *
>--
>1.8.3.1
---
-Jay Vosburgh, jay.vosburgh@canonical.com
next parent reply other threads:[~2020-10-29 1:47 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1603850163-4563-1-git-send-email-i@liuyulong.me>
2020-10-28 3:53 ` Jay Vosburgh [this message]
[not found] ` <5f99529c.1c69fb81.aa4b3.6707SMTPIN_ADDED_BROKEN@mx.google.com>
2020-10-28 19:37 ` [PATCH] net: bonding: alb disable balance for IPv6 multicast related mac Jay Vosburgh
2020-11-02 7:51 ` update my thread mail address LIU Yulong
2020-11-02 7:56 ` [PATCH v2] net: bonding: alb disable balance for IPv6 multicast related mac LIU Yulong
2020-11-03 21:05 ` Jakub Kicinski
2020-11-07 18:39 ` Jakub Kicinski
2020-11-08 21:37 ` Jay Vosburgh
2020-11-09 10:03 ` LIU Yulong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=22348.1603857233@famine \
--to=jay.vosburgh@canonical.com \
--cc=andy@greyhouse.net \
--cc=davem@davemloft.net \
--cc=i@liuyulong.me \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=vfalico@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.