All of lore.kernel.org
 help / color / mirror / Atom feed
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: "Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>
Cc: Kieran Bingham <kieran.bingham@ideasonboard.com>,
	Jacopo Mondi <jacopo@jmondi.org>,
	linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v3 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter
Date: Mon, 05 Nov 2018 13:01:43 +0200	[thread overview]
Message-ID: <2284392.jROv1qFbmM@avalon> (raw)
In-Reply-To: <20181102160009.17267-5-niklas.soderlund+renesas@ragnatech.se>

Hi Niklas,

Thank you for the patch.

On Friday, 2 November 2018 18:00:09 EET Niklas Söderlund wrote:
> The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
> operate using 1-, 2- and 4-lanes. Update the driver to support all modes
> the hardware does.

"all modes the hardware does" sounds weird. How about simple "all available 
modes" ?

> The driver make use of large tables of static register/value writes when

s/make/makes/

> powering up/down the TXA and TXB transmitters which include the write to
> the NUM_LANES register. By converting the tables into functions and
> using parameters the power up/down functions for TXA and TXB power
> up/down can be merged and used for both transmitters.
> 
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The code looks so much better now :-)

> ---
> * Changes since v2
> - Fix typos in comments.
> - Remove unneeded boiler plait code in adv748x_tx_power() as suggested
>   by Jacopo and Laurent.
> - Take into account the two different register used when powering up TXA
>   and TXB due to an earlier patch in this series aligns the power
>   sequence with the manual.
> 
> * Changes since v1
> - Convert tables of register/value writes into functions instead of
>   intercepting and modifying the writes to the NUM_LANES register.
> ---
>  drivers/media/i2c/adv748x/adv748x-core.c | 157 ++++++++++++-----------
>  1 file changed, 79 insertions(+), 78 deletions(-)
> 
> diff --git a/drivers/media/i2c/adv748x/adv748x-core.c
> b/drivers/media/i2c/adv748x/adv748x-core.c index
> 9d80d7f3062b16bc..d94c63cb6a2efdba 100644
> --- a/drivers/media/i2c/adv748x/adv748x-core.c
> +++ b/drivers/media/i2c/adv748x/adv748x-core.c
> @@ -125,6 +125,16 @@ int adv748x_write(struct adv748x_state *state, u8 page,
> u8 reg, u8 value) return regmap_write(state->regmap[page], reg, value);
>  }
> 
> +static int adv748x_write_check(struct adv748x_state *state, u8 page, u8
> reg,
> +			       u8 value, int *error)
> +{
> +	if (*error)
> +		return *error;
> +
> +	*error = adv748x_write(state, page, reg, value);
> +	return *error;
> +}
> +
>  /* adv748x_write_block(): Write raw data with a maximum of
> I2C_SMBUS_BLOCK_MAX * size to one or more registers.
>   *
> @@ -231,79 +241,77 @@ static int adv748x_write_regs(struct adv748x_state
> *state, * TXA and TXB
>   */
> 
> -static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = {
> -
> -	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
> -	{ADV748X_PAGE_TXA, 0x00, 0xa4},	/* Set Auto DPHY Timing */
> -	{ADV748X_PAGE_TXA, 0xdb, 0x10},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xd6, 0x07},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xc4, 0x0a},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x71, 0x33},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x72, 0x11},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
> -
> -	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x1e, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
> -	{ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXA, 0xc1, 0x2b},	/* ADI Required Write */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXA, 0x31, 0x80},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = {
> -
> -	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x1e, 0x00},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
> -	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_TXA, 0xc1, 0x3b},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = {
> -
> -	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
> -	{ADV748X_PAGE_TXB, 0x00, 0xa1},	/* Set Auto DPHY Timing */
> -	{ADV748X_PAGE_TXB, 0xd2, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xc4, 0x0a},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x71, 0x33},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x72, 0x11},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
> -
> -	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x1e, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
> -	{ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXB, 0xc1, 0x2b},	/* ADI Required Write */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXB, 0x31, 0x80},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = {
> -
> -	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x1e, 0x00},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
> -	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_TXB, 0xc1, 0x3b},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> +static int adv748x_power_up_tx(struct adv748x_csi2 *tx)
> +{
> +	struct adv748x_state *state = tx->state;
> +	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
> +	int ret = 0;
> +
> +	/* Enable n-lane MIPI */
> +	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
> +
> +	/* Set Auto DPHY Timing */
> +	adv748x_write_check(state, page, 0x00, 0xa0 | tx->num_lanes, &ret);
> +
> +	/* ADI Required Write */
> +	if (is_txa(tx)) {
> +		adv748x_write_check(state, page, 0xdb, 0x10, &ret);
> +		adv748x_write_check(state, page, 0xd6, 0x07, &ret);
> +	} else {
> +		adv748x_write_check(state, page, 0xd2, 0x40, &ret);
> +	}
> +
> +	adv748x_write_check(state, page, 0xc4, 0x0a, &ret);
> +	adv748x_write_check(state, page, 0x71, 0x33, &ret);
> +	adv748x_write_check(state, page, 0x72, 0x11, &ret);
> +
> +	/* i2c_dphy_pwdn - 1'b0 */
> +	adv748x_write_check(state, page, 0xf0, 0x00, &ret);
> +
> +	/* ADI Required Writes*/
> +	adv748x_write_check(state, page, 0x31, 0x82, &ret);
> +	adv748x_write_check(state, page, 0x1e, 0x40, &ret);
> +
> +	/* i2c_mipi_pll_en - 1'b1 */
> +	adv748x_write_check(state, page, 0xda, 0x01, &ret);
> +	usleep_range(2000, 2500);
> +
> +	/* Power-up CSI-TX */
> +	adv748x_write_check(state, page, 0x00, 0x20 | tx->num_lanes, &ret);
> +	usleep_range(1000, 1500);
> +
> +	/* ADI Required Writes */
> +	adv748x_write_check(state, page, 0xc1, 0x2b, &ret);
> +	usleep_range(1000, 1500);
> +	adv748x_write_check(state, page, 0x31, 0x80, &ret);
> +
> +	return ret;
> +}
> +
> +static int adv748x_power_down_tx(struct adv748x_csi2 *tx)
> +{
> +	struct adv748x_state *state = tx->state;
> +	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
> +	int ret = 0;
> +
> +	/* ADI Required Writes */
> +	adv748x_write_check(state, page, 0x31, 0x82, &ret);
> +	adv748x_write_check(state, page, 0x1e, 0x00, &ret);
> +
> +	/* Enable n-lane MIPI */
> +	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
> +
> +	/* i2c_mipi_pll_en - 1'b1 */
> +	adv748x_write_check(state, page, 0xda, 0x01, &ret);
> +
> +	/* ADI Required Write */
> +	adv748x_write_check(state, page, 0xc1, 0x3b, &ret);
> +
> +	return ret;
> +}
> 
>  int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
>  {
> -	struct adv748x_state *state = tx->state;
> -	const struct adv748x_reg_value *reglist;
>  	int val;
> 
>  	if (!is_tx_enabled(tx))
> @@ -321,14 +329,7 @@ int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
>  	WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN),
>  			"Enabling with unknown bit set");
> 
> -	if (on)
> -		reglist = is_txa(tx) ? adv748x_power_up_txa_4lane :
> -				       adv748x_power_up_txb_1lane;
> -	else
> -		reglist = is_txa(tx) ? adv748x_power_down_txa_4lane :
> -				       adv748x_power_down_txb_1lane;
> -
> -	return adv748x_write_regs(state, reglist);
> +	return on ? adv748x_power_up_tx(tx) : adv748x_power_down_tx(tx);
>  }
> 
>  /* ------------------------------------------------------------------------

-- 
Regards,

Laurent Pinchart

  parent reply	other threads:[~2018-11-05 20:20 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-02 16:00 [PATCH v3 0/4] i2c: adv748x: add support for CSI-2 TXA to work Niklas Söderlund
2018-11-02 16:00 ` [PATCH v3 1/4] dt-bindings: adv748x: make data-lanes property mandatory for CSI-2 endpoints Niklas Söderlund
2018-11-05  8:41   ` jacopo mondi
2018-11-05 20:39     ` Rob Herring
2018-11-05 20:39       ` Rob Herring
2018-11-05 10:43   ` Laurent Pinchart
2018-11-02 16:00 ` [PATCH v3 2/4] i2c: adv748x: reuse power up sequence when initializing CSI-2 Niklas Söderlund
2018-11-05 10:52   ` Laurent Pinchart
2018-11-02 16:00 ` [PATCH v3 3/4] i2c: adv748x: store number of CSI-2 lanes described in device tree Niklas Söderlund
2018-11-05  8:58   ` jacopo mondi
2018-11-05 10:56   ` Laurent Pinchart
2018-11-02 16:00 ` [PATCH v3 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter Niklas Söderlund
2018-11-05  8:47   ` jacopo mondi
2018-11-05 11:01   ` Laurent Pinchart [this message]
2018-11-23 14:01   ` jacopo mondi
2018-11-23 14:43     ` Laurent Pinchart
2018-11-25 10:09       ` jacopo mondi
2018-11-05 10:19 ` [PATCH v3 0/4] i2c: adv748x: add support for CSI-2 TXA to work jacopo mondi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=2284392.jROv1qFbmM@avalon \
    --to=laurent.pinchart@ideasonboard.com \
    --cc=jacopo@jmondi.org \
    --cc=kieran.bingham@ideasonboard.com \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=niklas.soderlund+renesas@ragnatech.se \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.