From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: from galahad.ideasonboard.com ([185.26.127.97]:49328 "EHLO galahad.ideasonboard.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1750990AbdFTHos (ORCPT ); Tue, 20 Jun 2017 03:44:48 -0400 From: Laurent Pinchart To: Jacopo Mondi Cc: niklas.soderlund@ragnatech.se, linux-renesas-soc@vger.kernel.org Subject: Re: [PATCH v1 01/12] arm64: boot: dts: salvator-x: Add camera module Date: Tue, 20 Jun 2017 10:45:23 +0300 Message-ID: <2434403.6L5sxSsJ9D@avalon> In-Reply-To: <1497891889-8038-2-git-send-email-jacopo+renesas@jmondi.org> References: <1497891889-8038-1-git-send-email-jacopo+renesas@jmondi.org> <1497891889-8038-2-git-send-email-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Content-Transfer-Encoding: 7Bit Content-Type: text/plain; charset="us-ascii" Sender: linux-renesas-soc-owner@vger.kernel.org List-ID: Hi Jacopo, Thank you for the patch. On Monday 19 Jun 2017 19:04:38 Jacopo Mondi wrote: > Add camera module to Salvator-X M3W device tree. > The camera module sits on a i2c-gpio interface and it connected to VIN > channel #4 parallel video input port. > > Signed-off-by: Jacopo Mondi > --- > arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 35 +++++++++++++++++++ > 1 file changed, 35 insertions(+) > > diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts > b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts index ca4eb98..41c94c3 > 100644 > --- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts > +++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts > @@ -103,6 +103,41 @@ > states = <3300000 1 > 1800000 0>; > }; > + > + camera_module { This node describes an I2C master controller, it should be called accordingly. > + compatible = "i2c-gpio"; > + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH > + &gpio1 11 GPIO_ACTIVE_HIGH > + >; > + > + i2c-gpio,delay-us = <4>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + mclk: xclk { > + compatible = "fixed-clock"; > + #clock-cells = <1>; > + clock-frequency = <27000000>; > + clock-output-names = "mclk"; > + }; This node describes a fixed oscillator not connected to the I2C bus, so it should be moved to the top-level of the device tree instead of being a child of the I2C controller. > + camera: mt9m111@48 { No need for a label, and you should call the node according to its function, not the device model. Maybe something like camera-sensor@48 ? Or just camera@48 ? > + compatible = "micron,mt9m111"; > + reg = <0x48>; > + > + clocks = <&mclk 0>; > + clock-names = "mclk"; > + > + port { > + mt9m111_out: endpoint { > + bus_width = <8>; > + remote-endpoint = <&vin4_in>; > + }; > + }; > + }; > + }; > + > }; > > &pfc { -- Regards, Laurent Pinchart