Re: [PATCH v7 06/11] arm64: dts: freescale: add i.MX91 11x11 EVK basic support

[Alexander Stein <alexander.stein@ew.tq-group.com>]

Hi,

Am Montag, 28. Juli 2025, 09:14:33 CEST schrieb Joy Zou:
> Add i.MX91 11x11 EVK board support.
> - Enable ADC1.
> - Enable lpuart1 and lpuart5.
> - Enable network eqos and fec.
> - Enable I2C bus and children nodes under I2C bus.
> - Enable USB and related nodes.
> - Enable uSDHC1 and uSDHC2.
> - Enable Watchdog3.
> 
> Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
> Signed-off-by: Joy Zou <joy.zou@nxp.com>
> ---
> Changes for v7:
> 1. remove this unused comments, there are not imx91-11x11-evk-i3c.dts.
> 2. align all pinctrl value to the same column.
> 3. add aliases because remove aliases from common dtsi.
> 4. The 'eee-broken-1000t' flag disables Energy-Efficient Ethernet (EEE) on 1G
>    links as a workaround for PTP sync issues on older i.MX6 platforms.
>    Remove it since the i.MX91 have not such issue.
> 
> Changes for v6:
> 1. remove unused regulators and pinctrl settings.
> 
> Changes for v5:
> 1. change node name codec and lsm6dsm into common name audio-codec and
>    inertial-meter, and add BT compatible string.
> 
> Changes for v4:
> 1. remove pmic node unused newline.
> 2. delete the tcpc@50 status property.
> 3. align pad hex values.
> 
> Changes for v3:
> 1. format imx91-11x11-evk.dts with the dt-format tool.
> 2. add lpi2c1 node.
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../boot/dts/freescale/imx91-11x11-evk.dts    | 674 ++++++++++++++++++
>  2 files changed, 675 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx91-11x11-evk.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 0b473a23d120..fbedb3493c09 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -315,6 +315,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-tqma8xqp-mba8xx.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8qxp-tqma8xqps-mb-smarc-2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx93-9x9-qsb.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx91-11x11-evk.dtb

Please add imx91 before imx93, otherwise inserting will be a pain.

Best regards,
Alexander

>  
>  imx93-9x9-qsb-i3c-dtbs += imx93-9x9-qsb.dtb imx93-9x9-qsb-i3c.dtbo
>  dtb-$(CONFIG_ARCH_MXC) += imx93-9x9-qsb-i3c.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx91-11x11-evk.dts b/arch/arm64/boot/dts/freescale/imx91-11x11-evk.dts
> new file mode 100644
> index 000000000000..aca78768dbd4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx91-11x11-evk.dts
> @@ -0,0 +1,674 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2025 NXP
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/usb/pd.h>
> +#include "imx91.dtsi"
> +
> +/ {
> +	compatible = "fsl,imx91-11x11-evk", "fsl,imx91";
> +	model = "NXP i.MX91 11X11 EVK board";
> +
> +	aliases {
> +		ethernet0 = &fec;
> +		ethernet1 = &eqos;
> +		gpio0 = &gpio1;
> +		gpio1 = &gpio2;
> +		gpio2 = &gpio3;
> +		i2c0 = &lpi2c1;
> +		i2c1 = &lpi2c2;
> +		i2c2 = &lpi2c3;
> +		mmc0 = &usdhc1;
> +		mmc1 = &usdhc2;
> +		rtc0 = &bbnsm_rtc;
> +		serial0 = &lpuart1;
> +		serial1 = &lpuart2;
> +		serial2 = &lpuart3;
> +		serial3 = &lpuart4;
> +		serial4 = &lpuart5;
> +	};
> +
> +	chosen {
> +		stdout-path = &lpuart1;
> +	};
> +
> +	reg_vref_1v8: regulator-adc-vref {
> +		compatible = "regulator-fixed";
> +		regulator-max-microvolt = <1800000>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-name = "vref_1v8";
> +	};
> +
> +	reg_audio_pwr: regulator-audio-pwr {
> +		compatible = "regulator-fixed";
> +		regulator-always-on;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-name = "audio-pwr";
> +		gpio = <&adp5585 1 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2 {
> +		compatible = "regulator-fixed";
> +		off-on-delay-us = <12000>;
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		pinctrl-names = "default";
> +		regulator-max-microvolt = <3300000>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-name = "VSD_3V3";
> +		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reserved-memory {
> +		ranges;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +
> +		linux,cma {
> +			compatible = "shared-dma-pool";
> +			alloc-ranges = <0 0x80000000 0 0x40000000>;
> +			reusable;
> +			size = <0 0x10000000>;
> +			linux,cma-default;
> +		};
> +	};
> +};
> +
> +&adc1 {
> +	vref-supply = <&reg_vref_1v8>;
> +	status = "okay";
> +};
> +
> +&eqos {
> +	phy-handle = <&ethphy1>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-0 = <&pinctrl_eqos>;
> +	pinctrl-1 = <&pinctrl_eqos_sleep>;
> +	pinctrl-names = "default", "sleep";
> +	status = "okay";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		clock-frequency = <5000000>;
> +
> +		ethphy1: ethernet-phy@1 {
> +			reg = <1>;
> +			realtek,clkout-disable;
> +		};
> +	};
> +};
> +
> +&fec {
> +	phy-handle = <&ethphy2>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-0 = <&pinctrl_fec>;
> +	pinctrl-1 = <&pinctrl_fec_sleep>;
> +	pinctrl-names = "default", "sleep";
> +	fsl,magic-packet;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		clock-frequency = <5000000>;
> +
> +		ethphy2: ethernet-phy@2 {
> +			reg = <2>;
> +			realtek,clkout-disable;
> +		};
> +	};
> +};
> +
> +&lpi2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&pinctrl_lpi2c1>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	audio_codec: wm8962@1a {
> +		compatible = "wlf,wm8962";
> +		reg = <0x1a>;
> +		clocks = <&clk IMX93_CLK_SAI3_GATE>;
> +		AVDD-supply = <&reg_audio_pwr>;
> +		CPVDD-supply = <&reg_audio_pwr>;
> +		DBVDD-supply = <&reg_audio_pwr>;
> +		DCVDD-supply = <&reg_audio_pwr>;
> +		MICVDD-supply = <&reg_audio_pwr>;
> +		PLLVDD-supply = <&reg_audio_pwr>;
> +		SPKVDD1-supply = <&reg_audio_pwr>;
> +		SPKVDD2-supply = <&reg_audio_pwr>;
> +		gpio-cfg = <
> +			0x0000 /* 0:Default */
> +			0x0000 /* 1:Default */
> +			0x0000 /* 2:FN_DMICCLK */
> +			0x0000 /* 3:Default */
> +			0x0000 /* 4:FN_DMICCDAT */
> +			0x0000 /* 5:Default */
> +		>;
> +	};
> +
> +	inertial-meter@6a {
> +		compatible = "st,lsm6dso";
> +		reg = <0x6a>;
> +	};
> +};
> +
> +&lpi2c2 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&pinctrl_lpi2c2>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	pcal6524: gpio@22 {
> +		compatible = "nxp,pcal6524";
> +		reg = <0x22>;
> +		#interrupt-cells = <2>;
> +		interrupt-controller;
> +		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> +		#gpio-cells = <2>;
> +		gpio-controller;
> +		interrupt-parent = <&gpio3>;
> +		pinctrl-0 = <&pinctrl_pcal6524>;
> +		pinctrl-names = "default";
> +	};
> +
> +	pmic@25 {
> +		compatible = "nxp,pca9451a";
> +		reg = <0x25>;
> +		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&pcal6524>;
> +
> +		regulators {
> +			buck1: BUCK1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <2237500>;
> +				regulator-min-microvolt = <650000>;
> +				regulator-name = "BUCK1";
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			buck2: BUCK2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <2187500>;
> +				regulator-min-microvolt = <600000>;
> +				regulator-name = "BUCK2";
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			buck4: BUCK4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-min-microvolt = <600000>;
> +				regulator-name = "BUCK4";
> +			};
> +
> +			buck5: BUCK5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-min-microvolt = <600000>;
> +				regulator-name = "BUCK5";
> +			};
> +
> +			buck6: BUCK6 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-min-microvolt = <600000>;
> +				regulator-name = "BUCK6";
> +			};
> +
> +			ldo1: LDO1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-min-microvolt = <1600000>;
> +				regulator-name = "LDO1";
> +			};
> +
> +			ldo4: LDO4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-min-microvolt = <800000>;
> +				regulator-name = "LDO4";
> +			};
> +
> +			ldo5: LDO5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-name = "LDO5";
> +			};
> +		};
> +	};
> +
> +	adp5585: io-expander@34 {
> +		compatible = "adi,adp5585-00", "adi,adp5585";
> +		reg = <0x34>;
> +		#gpio-cells = <2>;
> +		gpio-controller;
> +		#pwm-cells = <3>;
> +		gpio-reserved-ranges = <5 1>;
> +
> +		exp-sel-hog {
> +			gpio-hog;
> +			gpios = <4 GPIO_ACTIVE_HIGH>;
> +			output-low;
> +		};
> +	};
> +};
> +
> +&lpi2c3 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&pinctrl_lpi2c3>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	ptn5110: tcpc@50 {
> +		compatible = "nxp,ptn5110", "tcpci";
> +		reg = <0x50>;
> +		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-parent = <&gpio3>;
> +
> +		typec1_con: connector {
> +			compatible = "usb-c-connector";
> +			data-role = "dual";
> +			label = "USB-C";
> +			op-sink-microwatt = <15000000>;
> +			power-role = "dual";
> +			self-powered;
> +			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> +				     PDO_VAR(5000, 20000, 3000)>;
> +			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> +			try-power-role = "sink";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					typec1_dr_sw: endpoint {
> +						remote-endpoint = <&usb1_drd_sw>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	ptn5110_2: tcpc@51 {
> +		compatible = "nxp,ptn5110", "tcpci";
> +		reg = <0x51>;
> +		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-parent = <&gpio3>;
> +		status = "okay";
> +
> +		typec2_con: connector {
> +			compatible = "usb-c-connector";
> +			data-role = "dual";
> +			label = "USB-C";
> +			op-sink-microwatt = <15000000>;
> +			power-role = "dual";
> +			self-powered;
> +			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> +				     PDO_VAR(5000, 20000, 3000)>;
> +			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> +			try-power-role = "sink";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					typec2_dr_sw: endpoint {
> +						remote-endpoint = <&usb2_drd_sw>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	pcf2131: rtc@53 {
> +		compatible = "nxp,pcf2131";
> +		reg = <0x53>;
> +		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&pcal6524>;
> +		status = "okay";
> +	};
> +};
> +
> +&lpuart1 {
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&lpuart5 {
> +	pinctrl-0 = <&pinctrl_uart5>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "nxp,88w8987-bt";
> +	};
> +};
> +
> +&usbotg1 {
> +	adp-disable;
> +	disable-over-current;
> +	dr_mode = "otg";
> +	hnp-disable;
> +	srp-disable;
> +	usb-role-switch;
> +	samsung,picophy-dc-vol-level-adjust = <7>;
> +	samsung,picophy-pre-emp-curr-control = <3>;
> +	status = "okay";
> +
> +	port {
> +		usb1_drd_sw: endpoint {
> +			remote-endpoint = <&typec1_dr_sw>;
> +		};
> +	};
> +};
> +
> +&usbotg2 {
> +	adp-disable;
> +	disable-over-current;
> +	dr_mode = "otg";
> +	hnp-disable;
> +	srp-disable;
> +	usb-role-switch;
> +	samsung,picophy-dc-vol-level-adjust = <7>;
> +	samsung,picophy-pre-emp-curr-control = <3>;
> +	status = "okay";
> +
> +	port {
> +		usb2_drd_sw: endpoint {
> +			remote-endpoint = <&typec2_dr_sw>;
> +		};
> +	};
> +};
> +
> +&usdhc1 {
> +	bus-width = <8>;
> +	non-removable;
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	bus-width = <4>;
> +	cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
> +	no-mmc;
> +	no-sdio;
> +	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_gpio_sleep>;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	status = "okay";
> +};
> +
> +&wdog3 {
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_eqos: eqosgrp {
> +		fsl,pins = <
> +			MX91_PAD_ENET1_MDC__ENET1_MDC                           0x57e
> +			MX91_PAD_ENET1_MDIO__ENET_QOS_MDIO                      0x57e
> +			MX91_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0                  0x57e
> +			MX91_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1                  0x57e
> +			MX91_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2                  0x57e
> +			MX91_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3                  0x57e
> +			MX91_PAD_ENET1_RXC__ENET_QOS_RGMII_RXC                  0x5fe
> +			MX91_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL            0x57e
> +			MX91_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0                  0x57e
> +			MX91_PAD_ENET1_TD1__ENET1_RGMII_TD1                     0x57e
> +			MX91_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2                  0x57e
> +			MX91_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3                  0x57e
> +			MX91_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK  0x5fe
> +			MX91_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL            0x57e
> +		>;
> +	};
> +
> +	pinctrl_eqos_sleep: eqossleepgrp {
> +		fsl,pins = <
> +			MX91_PAD_ENET1_MDC__GPIO4_IO0                           0x31e
> +			MX91_PAD_ENET1_MDIO__GPIO4_IO1                          0x31e
> +			MX91_PAD_ENET1_RD0__GPIO4_IO10                          0x31e
> +			MX91_PAD_ENET1_RD1__GPIO4_IO11                          0x31e
> +			MX91_PAD_ENET1_RD2__GPIO4_IO12                          0x31e
> +			MX91_PAD_ENET1_RD3__GPIO4_IO13                          0x31e
> +			MX91_PAD_ENET1_RXC__GPIO4_IO9                           0x31e
> +			MX91_PAD_ENET1_RX_CTL__GPIO4_IO8                        0x31e
> +			MX91_PAD_ENET1_TD0__GPIO4_IO5                           0x31e
> +			MX91_PAD_ENET1_TD1__GPIO4_IO4                           0x31e
> +			MX91_PAD_ENET1_TD2__GPIO4_IO3                           0x31e
> +			MX91_PAD_ENET1_TD3__GPIO4_IO2                           0x31e
> +			MX91_PAD_ENET1_TXC__GPIO4_IO7                           0x31e
> +			MX91_PAD_ENET1_TX_CTL__GPIO4_IO6                        0x31e
> +		>;
> +	};
> +
> +	pinctrl_fec: fecgrp {
> +		fsl,pins = <
> +			MX91_PAD_ENET2_MDC__ENET2_MDC                           0x57e
> +			MX91_PAD_ENET2_MDIO__ENET2_MDIO                         0x57e
> +			MX91_PAD_ENET2_RD0__ENET2_RGMII_RD0                     0x57e
> +			MX91_PAD_ENET2_RD1__ENET2_RGMII_RD1                     0x57e
> +			MX91_PAD_ENET2_RD2__ENET2_RGMII_RD2                     0x57e
> +			MX91_PAD_ENET2_RD3__ENET2_RGMII_RD3                     0x57e
> +			MX91_PAD_ENET2_RXC__ENET2_RGMII_RXC                     0x5fe
> +			MX91_PAD_ENET2_RX_CTL__ENET2_RGMII_RX_CTL               0x57e
> +			MX91_PAD_ENET2_TD0__ENET2_RGMII_TD0                     0x57e
> +			MX91_PAD_ENET2_TD1__ENET2_RGMII_TD1                     0x57e
> +			MX91_PAD_ENET2_TD2__ENET2_RGMII_TD2                     0x57e
> +			MX91_PAD_ENET2_TD3__ENET2_RGMII_TD3                     0x57e
> +			MX91_PAD_ENET2_TXC__ENET2_RGMII_TXC                     0x5fe
> +			MX91_PAD_ENET2_TX_CTL__ENET2_RGMII_TX_CTL               0x57e
> +		>;
> +	};
> +
> +	pinctrl_fec_sleep: fecsleepgrp {
> +		fsl,pins = <
> +			MX91_PAD_ENET2_MDC__GPIO4_IO14                          0x51e
> +			MX91_PAD_ENET2_MDIO__GPIO4_IO15                         0x51e
> +			MX91_PAD_ENET2_RD0__GPIO4_IO24                          0x51e
> +			MX91_PAD_ENET2_RD1__GPIO4_IO25                          0x51e
> +			MX91_PAD_ENET2_RD2__GPIO4_IO26                          0x51e
> +			MX91_PAD_ENET2_RD3__GPIO4_IO27                          0x51e
> +			MX91_PAD_ENET2_RXC__GPIO4_IO23                          0x51e
> +			MX91_PAD_ENET2_RX_CTL__GPIO4_IO22                       0x51e
> +			MX91_PAD_ENET2_TD0__GPIO4_IO19                          0x51e
> +			MX91_PAD_ENET2_TD1__GPIO4_IO18                          0x51e
> +			MX91_PAD_ENET2_TD2__GPIO4_IO17                          0x51e
> +			MX91_PAD_ENET2_TD3__GPIO4_IO16                          0x51e
> +			MX91_PAD_ENET2_TXC__GPIO4_IO21                          0x51e
> +			MX91_PAD_ENET2_TX_CTL__GPIO4_IO20                       0x51e
> +		>;
> +	};
> +
> +	pinctrl_lpi2c1: lpi2c1grp {
> +		fsl,pins = <
> +			MX91_PAD_I2C1_SCL__LPI2C1_SCL                           0x40000b9e
> +			MX91_PAD_I2C1_SDA__LPI2C1_SDA                           0x40000b9e
> +		>;
> +	};
> +
> +	pinctrl_lpi2c2: lpi2c2grp {
> +		fsl,pins = <
> +			MX91_PAD_I2C2_SCL__LPI2C2_SCL                           0x40000b9e
> +			MX91_PAD_I2C2_SDA__LPI2C2_SDA                           0x40000b9e
> +		>;
> +	};
> +
> +	pinctrl_lpi2c3: lpi2c3grp {
> +		fsl,pins = <
> +			MX91_PAD_GPIO_IO28__LPI2C3_SDA                          0x40000b9e
> +			MX91_PAD_GPIO_IO29__LPI2C3_SCL                          0x40000b9e
> +		>;
> +	};
> +
> +	pinctrl_pcal6524: pcal6524grp {
> +		fsl,pins = <
> +			MX91_PAD_CCM_CLKO2__GPIO3_IO27                          0x31e
> +		>;
> +	};
> +
> +	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_RESET_B__GPIO3_IO7                         0x31e
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX91_PAD_UART1_RXD__LPUART1_RX                          0x31e
> +			MX91_PAD_UART1_TXD__LPUART1_TX                          0x31e
> +		>;
> +	};
> +
> +	pinctrl_uart5: uart5grp {
> +		fsl,pins = <
> +			MX91_PAD_DAP_TDO_TRACESWO__LPUART5_TX                   0x31e
> +			MX91_PAD_DAP_TDI__LPUART5_RX                            0x31e
> +			MX91_PAD_DAP_TMS_SWDIO__LPUART5_RTS_B                   0x31e
> +			MX91_PAD_DAP_TCLK_SWCLK__LPUART5_CTS_B                  0x31e
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD1_CLK__USDHC1_CLK                            0x158e
> +			MX91_PAD_SD1_CMD__USDHC1_CMD                            0x138e
> +			MX91_PAD_SD1_DATA0__USDHC1_DATA0                        0x138e
> +			MX91_PAD_SD1_DATA1__USDHC1_DATA1                        0x138e
> +			MX91_PAD_SD1_DATA2__USDHC1_DATA2                        0x138e
> +			MX91_PAD_SD1_DATA3__USDHC1_DATA3                        0x138e
> +			MX91_PAD_SD1_DATA4__USDHC1_DATA4                        0x138e
> +			MX91_PAD_SD1_DATA5__USDHC1_DATA5                        0x138e
> +			MX91_PAD_SD1_DATA6__USDHC1_DATA6                        0x138e
> +			MX91_PAD_SD1_DATA7__USDHC1_DATA7                        0x138e
> +			MX91_PAD_SD1_STROBE__USDHC1_STROBE                      0x158e
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD1_CLK__USDHC1_CLK                            0x15fe
> +			MX91_PAD_SD1_CMD__USDHC1_CMD                            0x13fe
> +			MX91_PAD_SD1_DATA0__USDHC1_DATA0                        0x13fe
> +			MX91_PAD_SD1_DATA1__USDHC1_DATA1                        0x13fe
> +			MX91_PAD_SD1_DATA2__USDHC1_DATA2                        0x13fe
> +			MX91_PAD_SD1_DATA3__USDHC1_DATA3                        0x13fe
> +			MX91_PAD_SD1_DATA4__USDHC1_DATA4                        0x13fe
> +			MX91_PAD_SD1_DATA5__USDHC1_DATA5                        0x13fe
> +			MX91_PAD_SD1_DATA6__USDHC1_DATA6                        0x13fe
> +			MX91_PAD_SD1_DATA7__USDHC1_DATA7                        0x13fe
> +			MX91_PAD_SD1_STROBE__USDHC1_STROBE                      0x15fe
> +		>;
> +	};
> +
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +			MX91_PAD_SD1_CLK__USDHC1_CLK                            0x1582
> +			MX91_PAD_SD1_CMD__USDHC1_CMD                            0x1382
> +			MX91_PAD_SD1_DATA0__USDHC1_DATA0                        0x1382
> +			MX91_PAD_SD1_DATA1__USDHC1_DATA1                        0x1382
> +			MX91_PAD_SD1_DATA2__USDHC1_DATA2                        0x1382
> +			MX91_PAD_SD1_DATA3__USDHC1_DATA3                        0x1382
> +			MX91_PAD_SD1_DATA4__USDHC1_DATA4                        0x1382
> +			MX91_PAD_SD1_DATA5__USDHC1_DATA5                        0x1382
> +			MX91_PAD_SD1_DATA6__USDHC1_DATA6                        0x1382
> +			MX91_PAD_SD1_DATA7__USDHC1_DATA7                        0x1382
> +			MX91_PAD_SD1_STROBE__USDHC1_STROBE                      0x1582
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_CLK__USDHC2_CLK                            0x158e
> +			MX91_PAD_SD2_CMD__USDHC2_CMD                            0x138e
> +			MX91_PAD_SD2_DATA0__USDHC2_DATA0                        0x138e
> +			MX91_PAD_SD2_DATA1__USDHC2_DATA1                        0x138e
> +			MX91_PAD_SD2_DATA2__USDHC2_DATA2                        0x138e
> +			MX91_PAD_SD2_DATA3__USDHC2_DATA3                        0x138e
> +			MX91_PAD_SD2_VSELECT__USDHC2_VSELECT                    0x51e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_CLK__USDHC2_CLK                            0x15fe
> +			MX91_PAD_SD2_CMD__USDHC2_CMD                            0x13fe
> +			MX91_PAD_SD2_DATA0__USDHC2_DATA0                        0x13fe
> +			MX91_PAD_SD2_DATA1__USDHC2_DATA1                        0x13fe
> +			MX91_PAD_SD2_DATA2__USDHC2_DATA2                        0x13fe
> +			MX91_PAD_SD2_DATA3__USDHC2_DATA3                        0x13fe
> +			MX91_PAD_SD2_VSELECT__USDHC2_VSELECT                    0x51e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_CD_B__GPIO3_IO0                            0x31e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_gpio_sleep: usdhc2gpiosleepgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_CD_B__GPIO3_IO0                            0x51e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_CLK__USDHC2_CLK                            0x1582
> +			MX91_PAD_SD2_CMD__USDHC2_CMD                            0x1382
> +			MX91_PAD_SD2_DATA0__USDHC2_DATA0                        0x1382
> +			MX91_PAD_SD2_DATA1__USDHC2_DATA1                        0x1382
> +			MX91_PAD_SD2_DATA2__USDHC2_DATA2                        0x1382
> +			MX91_PAD_SD2_DATA3__USDHC2_DATA3                        0x1382
> +			MX91_PAD_SD2_VSELECT__USDHC2_VSELECT                    0x51e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_sleep: usdhc2sleepgrp {
> +		fsl,pins = <
> +			MX91_PAD_SD2_CLK__GPIO3_IO1                             0x51e
> +			MX91_PAD_SD2_CMD__GPIO3_IO2                             0x51e
> +			MX91_PAD_SD2_DATA0__GPIO3_IO3                           0x51e
> +			MX91_PAD_SD2_DATA1__GPIO3_IO4                           0x51e
> +			MX91_PAD_SD2_DATA2__GPIO3_IO5                           0x51e
> +			MX91_PAD_SD2_DATA3__GPIO3_IO6                           0x51e
> +			MX91_PAD_SD2_VSELECT__GPIO3_IO19                        0x51e
> +		>;
> +	};
> +
> +};
> 


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/