From: rolf liu <rolfliu@gmail.com>
To: ppopov@embeddedalley.com
Cc: "linux-mips@linux-mips.org" <linux-mips@linux-mips.org>
Subject: Re: booting error on db1550 using linux 2.6.12 from linux-mips.org
Date: Fri, 1 Jul 2005 15:52:41 -0700 [thread overview]
Message-ID: <2db32b720507011552403f22c4@mail.gmail.com> (raw)
In-Reply-To: <1120257851.5987.37.camel@localhost.localdomain>
I used that patch to force 371 to use 372 timing to 2.4.31. but
unfortunately, the kernel crashed during the probing process. any
idea?
thanks
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
HPT371: IDE controller at PCI slot 00:0b.0
HPT371: chipset revision 2
HPT371: not 100% native mode: will probe irqs later
hpt: HPT372N detected, using 372N timing.
FREQ: 73 PLL: 35
hpt: no known IDE timings, disabling DMA.
hpt: no known IDE timings, disabling DMA.
probing for hda: present=0, media=32, probetype=ATA
probing for hda: present=0, media=32, probetype=ATAPI
probing for hdb: present=0, media=32, probetype=ATA
probing for hdb: present=0, media=32, probetype=ATAPI
probing for hdc: present=0, media=32, probetype=ATA
probing for hdc: present=0, media=32, probetype=ATAPI
probing for hdd: present=0, media=32, probetype=ATA
probing for hdd: present=0, media=32, probetype=ATAPI
probing for hde: present=0, media=32, probetype=ATA
probing for hde: present=0, media=32, probetype=ATAPI
probing for hdf: present=0, media=32, probetype=ATA
probing for hdf: present=0, media=32, probetype=ATAPI
probing for hdg: present=0, media=32, probetype=ATA
hdg: IBM-DTTA-350840, ATA DISK drive
probing for hdh: present=0, media=32, probetype=ATA
probing for hdh: present=0, media=32, probetype=ATAPI
Unable to handle kernel paging request at virtual address 00000000,
epc == 801e77f0, ra == 801e7b48
Oops in fault.c::do_page_fault, line 206:
On 7/1/05, Pete Popov <ppopov@embeddedalley.com> wrote:
> On Fri, 2005-07-01 at 15:35 -0700, rolf liu wrote:
> > thanks, Pete.
> > I applied the patch, it can mount the root now. Such a delicate patch.
> >
> > Have you made the HPT371N working for 2.6 tree?
>
> One and off, yes. There was a timing issue I remember ... I had a 2.4
> patch in my oss directory that worked fine for 2.4. I don't remember if
> the same patch worked ok in 2.6. I didn't have much time to debug it,
> but I remember when I put a few debug prints in the hpt init routine,
> the problem went away, indicating an initialization timing issue.
>
> Pete
>
> > When I want to
> > compile in the hpt366.c, the kernel will hang up right after it found
> > the disk drive:
> >
> > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> > HPT371: IDE controller at PCI slot 0000:00:0b.0
> > PCI: Enabling device 0000:00:0b.0 (0000 -> 0003)
> > HPT371: chipset revision 2
> > HPT37X: using 33MHz PCI clock
> > HPT371: 100% native mode on irq 5
> > ide2: BM-DMA at 0x1000-0x1007, BIOS settings: hde:pio, hdf:pio
> > ide3: BM-DMA at 0x1008-0x100f, BIOS settings: hdg:pio, hdh:pio
> > hdg: IBM-DTTA-350840, ATA DISK drive
> >
> > hang up ................ :(
> >
> >
> > On 7/1/05, Pete Popov <ppopov@embeddedalley.com> wrote:
> > >
> > > <snip>
> > >
> > > The problem below is caused by a .mips3 directive in xchg_u32. I talked
> > > to Ralf and Maciel about the problem; Ralf sent a patch but I don't see
> > > it applied in the tree yet. Try this:
> > >
> > > Index: include/asm-mips/system.h
> > > ===================================================================
> > > RCS file: /home/cvs/linux/include/asm-mips/system.h,v
> > > retrieving revision 1.85
> > > diff -u -r1.85 system.h
> > > --- include/asm-mips/system.h 23 Jun 2005 15:57:18 -0000 1.85
> > > +++ include/asm-mips/system.h 29 Jun 2005 12:01:54 -0000
> > > @@ -178,7 +178,9 @@
> > > __asm__ __volatile__(
> > > " .set mips3 \n"
> > > "1: ll %0, %3 #
> > > xchg_u32 \n"
> > > + " .set mips0 \n"
> > > " move %2, %
> > > z4 \n"
> > > + " .set mips3 \n"
> > > " sc %2, %
> > > 1 \n"
> > > " beqzl %2,
> > > 1b \n"
> > > ROT_IN_PIECES
> > > @@ -195,7 +197,9 @@
> > > __asm__ __volatile__(
> > > " .set mips3 \n"
> > > "1: ll %0, %3 #
> > > xchg_u32 \n"
> > > + " .set mips0 \n"
> > > " move %2, %
> > > z4 \n"
> > > + " .set mips3 \n"
> > > " sc %2, %
> > > 1 \n"
> > > " beqz %2,
> > > 1b \n"
> > > #ifdef CONFIG_SMP
> > >
> > >
> > >
> > > Pete
> > >
> > > > eth1: link up
> > > > ., OK
> > > > IP-Config: Got DHCP answer from 255.255.255.255, my address is 10.200.1.54
> > > > IP-Config: Complete:
> > > > device=eth0, addr=10.200.1.54, mask=255.255.0.0, gw=10.200.0.1,
> > > > host=10.200.1.54, domain=sel, nis-domain=(none),
> > > > bootserver=255.255.255.255, rootserver=10.200.0.198, rootpath=
> > > > Looking up port of RPC 100003/2 on 10.200.0.198
> > > > Reserved instruction in kernel code in
> > > > arch/mips/kernel/traps.c::do_ri, line 706[#1]:
> > > > Cpu 0
> > > > $ 0 : 00000000 1000fc00 00010000 00000000
> > > > $ 4 : 812b8e40 00000093 00000000 811df97c
> > > > $ 8 : 00000040 812b9e40 00000000 812a4e10
> > > > $12 : 0000ffff 00200200 00100100 812a3ef4
> > > > $16 : 812b8e40 00000000 812b8e40 00000060
> > > > $20 : 8042a6e0 00010000 811df90c 80144b20
> > > > $24 : 00000000 00000001
> > > > $28 : 811de000 811df8f0 8042a6e0 802facd0
> > > > Hi : 00000000
> > > > Lo : 00000780
> > > > epc : 802ca258 sock_alloc_send_skb+0x74/0x5c8 Not tainted
> > > > ra : 802facd0 ip_append_data+0x7c8/0xa34
> > > > Status: 1000fc03 KERNEL EXL IE
> > > > Cause : 00800028
> > > > PrId : 03030200
> > > > Modules linked in:
> > > > Process swapper (pid: 1, threadinfo=811de000, task=80456bf0)
> > > > Stack : c600c80a 3601c80a 00000000 00000000 00000000 00000000 00000000 00000000
> > > > 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> > > > 00000074 00000000 812b8e40 00000060 812b8e40 812b9e40 00000060 00000008
> > > > 812b8e98 802facd0 00000000 00000093 00000000 811df97c 00000000 00000000
> > > > 00000000 00000000 812b9e40 00000000 00000010 00000000 000005dc 00000000
> > > > ...
> > > > Call Trace:
> > > > [<802facd0>] ip_append_data+0x7c8/0xa34
> > > > [<8031e3c4>] udp_sendmsg+0x224/0xa08
> > > > [<802fa44c>] ip_generic_getfrag+0x0/0xbc
> > > > [<802c6558>] sock_sendmsg+0xac/0xf0
> > > > [<80334890>] fn_hash_lookup+0x100/0x150
> > > > [<80334890>] fn_hash_lookup+0x100/0x150
> > > > [<80144b20>] autoremove_wake_function+0x0/0x44
> > > > [<802c65c0>] kernel_sendmsg+0x24/0x38
> > > > [<80362f48>] xdr_sendpages+0x1dc/0x29c
> > > > [<80355284>] xprt_transmit+0xec/0x5f4
> > > > [<80144b20>] autoremove_wake_function+0x0/0x44
> > > > [<803529c4>] call_transmit+0x1f4/0x2d4
> > > > [<80356674>] rpc_delete_timer+0xdc/0x108
> > > > [<80357cb4>] __rpc_execute+0xa8/0x54c
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80144b20>] autoremove_wake_function+0x0/0x44
> > > > [<8035976c>] rpcauth_bindcred+0xac/0x248
> > > > [<80144b20>] autoremove_wake_function+0x0/0x44
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80351d28>] rpc_call_sync+0x8c/0xd8
> > > > [<80351d14>] rpc_call_sync+0x78/0xd8
> > > > [<80361fdc>] pmap_create+0x74/0xc0
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<803622e8>] rpc_getport_external+0x11c/0x180
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<8041b854>] root_nfs_getport+0x8c/0xa8
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80254000>] snprintf+0x14/0x20
> > > > [<8041bb94>] nfs_root_data+0x324/0x3a8
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80128f24>] printk+0x1c/0x28
> > > > [<80144b20>] autoremove_wake_function+0x0/0x44
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<8013e444>] flush_workqueue+0x28/0x34
> > > > [<80197f58>] path_lookup+0xe0/0x3d0
> > > > [<80194c78>] getname+0x28/0xf8
> > > > [<80198644>] __user_walk+0x78/0x94
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80409cb0>] mount_root+0xac/0x1c4
> > > > [<80144b20>] autoremove_wake_function+0x0/0x44
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80420000>] init_mtdchar+0x20/0x60
> > > > [<80409e10>] prepare_namespace+0x48/0x148
> > > > [<8013e444>] flush_workqueue+0x28/0x34
> > > > [<8010065c>] init+0x200/0x264
> > > > [<80100574>] init+0x118/0x264
> > > > [<80105e20>] kernel_thread_helper+0x10/0x18
> > > > [<80105e10>] kernel_thread_helper+0x0/0x18
> > > >
> > > >
> > > > Code: 10400091 0280f021 c20300a0 <0000102d> e20200a0 1040fffc
> > > > 00000000 00032823 14a0009f
> > > > Kernel panic - not syncing: Attempted to kill init!
> > > >
> > > >
> > > >
> > > >
> > > > Also, I tried to run 2.4.31 on db1550, but got no luck to get the hard
> > > > drive working, which also crashes during the probing process:
> > > > probing for hda: present=0, media=32, probetype=ATA
> > > > probing for hda: present=0, media=32, probetype=ATAPI
> > > > probing for hdb: present=0, media=32, probetype=ATA
> > > > probing for hdb: present=0, media=32, probetype=ATAPI
> > > > probing for hdc: present=0, media=32, probetype=ATA
> > > > probing for hdc: present=0, media=32, probetype=ATAPI
> > > > probing for hdd: present=0, media=32, probetype=ATA
> > > > probing for hdd: present=0, media=32, probetype=ATAPI
> > > > probing for hde: present=0, media=32, probetype=ATA
> > > > probing for hde: present=0, media=32, probetype=ATAPI
> > > > probing for hdf: present=0, media=32, probetype=ATA
> > > > probing for hdf: present=0, media=32, probetype=ATAPI
> > > > probing for hdg: present=0, media=32, probetype=ATA
> > > > hdg: IBM-DTTA-350840, ATA DISK drive
> > > > probing for hdh: present=0, media=32, probetype=ATA
> > > > probing for hdh: present=0, media=32, probetype=ATAPI
> > > > Unable to handle kernel paging request at virtual address 00000000,
> > > > epc == 801e77f0, ra == 801e7b48
> > > > Oops in fault.c::do_page_fault, line 206:
> > > >
> > >
> > >
> >
>
>
next prev parent reply other threads:[~2005-07-01 22:53 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-07-01 21:17 booting error on db1550 using linux 2.6.12 from linux-mips.org rolf liu
2005-07-01 21:24 ` Pete Popov
2005-07-01 22:35 ` rolf liu
2005-07-01 22:44 ` Pete Popov
2005-07-01 22:52 ` rolf liu [this message]
2005-07-05 15:50 ` rolf liu
2005-07-06 7:12 ` Pete Popov
2005-07-06 22:15 ` rolf liu
2005-07-06 22:22 ` Pete Popov
2005-07-07 17:10 ` Alan Cox
2005-07-07 17:19 ` rolf liu
2005-07-07 18:05 ` rolf liu
2005-07-07 18:42 ` rolf liu
2005-07-07 22:47 ` Alan Cox
2005-07-08 0:27 ` rolf liu
2005-07-08 19:27 ` rolf liu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2db32b720507011552403f22c4@mail.gmail.com \
--to=rolfliu@gmail.com \
--cc=linux-mips@linux-mips.org \
--cc=ppopov@embeddedalley.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.