From: "rom.132" <rom.132@voila.fr>
To: linux-kernel@vger.kernel.org
Subject: floppy problem 2.6.9
Date: Thu, 9 Sep 2004 15:53:07 +0200 (CEST) [thread overview]
Message-ID: <31554465.1094737987945.JavaMail.www@wwinf4005> (raw)
[1] floppy and USB key: modules mounted, devices work but error message
[2] Hi,
I had compiled a 2.6.8.1 kernel patched with patch-2.6.9-rc1. I'm using patch because I had the same problem with 2.6.8.1 but none with 2.6.6.
I could mount a CDROM but not floppy or USB key and the STDERR is the same:
_____________________________________________________________
# mount -t vfat /dev/df0 /media/floppy
floppy reader turn but call return this:
mount: wrong fs type, bad option, bad superblock on /dev/fd0,
or too many mounted file systems
-------------------------------------------------------------
I test my modules:
_____________________________________________________________
# modinfo floppy
vemagic: 2.6.8.1 K7 gcc-3.3
depend:
# modinfo vfat
...
vemagic 2.6.8.1 K7 gcc-3.3
depend: fat
-------------------------------------------------------------
I tried patching floppy.c only last day and booting after with floppy=noacpi. Awful, same result but my floppy reader turn everytime.
[7] My computer is a Presario 1211EA under Debian Sarge.
_____________________________________________________________________
# lspci -vvv
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at f8000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f4100000-f5ffffff
Prefetchable memory behind bridge: fff00000-000fffff
Expansion ROM at 00009000 [disabled] [size=4K]
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C/VT8235 PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1820 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 1800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.4 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 10
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 20)
Subsystem: Compaq Computer Corporation Soundmax integrated digital audio
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1000
Region 1: I/O ports at 1834 [size=4]
Region 2: I/O ports at 1830 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:09.0 Ethernet controller: Conexant HCF 56k Modem (rev 08)
Subsystem: Compaq Computer Corporation 623-LAN Grizzly
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 160 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
BIST result: 00
Region 0: I/O ports at 1400
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:09.1 Communication controller: Conexant HCF 56k Modem (rev 05)
Subsystem: Compaq Computer Corporation Yogi
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
BIST result: 00
Region 0: I/O ports at 1838
Region 1: Memory at f4004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
Subsystem: Compaq Computer Corporation: Unknown device b103
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 14000000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 00000000-00000000 (prefetchable)
Memory window 1: 00000000-00000000 (prefetchable)
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
16-bit legacy interface ports at 0001
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation: Unknown device 005f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f5000000 (32-bit, non-prefetchable)
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--------------------------------------------------------------------------------------------------------------
# scripts/ver_linux
Linux ares 2.6.8.1 #1 Thu Sep 9 14:28:09 CEST 2004 i686 GNU/Linux
Gnu C 3.3.3
Gnu make 3.80
binutils 2.14.90.0.7
util-linux 2.12
mount 2.12
module-init-tools 3.0-pre10
e2fsprogs 1.35
pcmcia-cs 3.2.5
quota-tools 3.11.
PPP 2.4.2
nfs-utils 1.0.6
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 3.2.1
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.0.91
Modules Loaded sd_mod usb_storage scsi_mod floppy tulip crc32 snd_via82xx snd_ac97_codec snd_pcm_oss snd_mixer_oss mousedev usbmouse snd_pcm snd_timer snd_page_alloc usbhid snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore uhci_hcd usbcore via_agp agpgart evdev ide_cd cdrom genrtc reiserfs vfat fat isofs ext2 ide_disk ide_generic via82cxxx generic ide_core unix
---------------------------------------------------------------------------------------------------------------
# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1000-10ff : 0000:00:07.5
1000-10ff : VIA686A
1400-14ff : 0000:00:09.0
1400-14ff : tulip
1800-181f : 0000:00:07.2
1800-181f : uhci_hcd
1820-182f : 0000:00:07.1
1820-1827 : ide0
1828-182f : ide1
1830-1833 : 0000:00:07.5
1830-1831 : VIA82xx MPU401
1834-1837 : 0000:00:07.5
1838-183f : 0000:00:09.1
8000-80ff : 0000:00:07.4
8000-808f : motherboard
8000-8003 : PM1a_EVT_BLK
8004-8005 : PM1a_CNT_BLK
8008-800b : PM_TMR
8020-8023 : GPE0_BLK
8100-810f : 0000:00:07.4
9000-9fff : PCI Bus #01
9000-90ff : 0000:01:00.0
--------------------------------------------------------------------------------------------------------
cat /proc/iomem
00000000-0009f3ff : System RAM
0009f400-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cffff : Video ROM
000dc000-000dffff : reserved
000f0000-000fffff : System ROM
00100000-13feffff : System RAM
00100000-0022a372 : Kernel code
0022a373-00281bff : Kernel data
13ff0000-13fffbff : ACPI Tables
13fffc00-13ffffff : ACPI Non-volatile Storage
14000000-14000fff : 0000:00:0a.0
f4000000-f4003fff : 0000:00:09.0
f4000000-f4003fff : tulip
f4004000-f4007fff : 0000:00:09.1
f4100000-f5ffffff : PCI Bus #01
f4100000-f4100fff : 0000:01:00.0
f5000000-f5ffffff : 0000:01:00.0
f8000000-fbffffff : 0000:00:00.0
fffe0000-ffffffff : reserved
----------------------------------------------------------------------------------------------------------
Actually, I don't know kernel to debug it myself but I'm working for. If Robert Love read this: thanks Robert your 'Linux Kernel Development' is wonderful!
------------------------------------------
Faites un voeu et puis Voila ! www.voila.fr
reply other threads:[~2004-09-09 13:55 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=31554465.1094737987945.JavaMail.www@wwinf4005 \
--to=rom.132@voila.fr \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.