From: michal.mleczko@gmail.com (Michał Mleczko)
To: lm-sensors@vger.kernel.org
Subject: [lm-sensors] Asus Z80V/M6V i2c support
Date: Thu, 22 Sep 2005 10:35:05 +0000 [thread overview]
Message-ID: <318b1df00509220134f03337b@mail.gmail.com> (raw)
In-Reply-To: <318b1df00509211647a24cdec@mail.gmail.com>
Hi,
thank you very much. I am using kernel 2.6.13. Could you give me some hints
as to where to look for the configuration registers? I would be interested
to find out more about this.
Anyway, here are the outputs:
# lspci -n
0000:00:00.0 Class 0600: 8086:2590 (rev 03)
0000:00:01.0 Class 0604: 8086:2591 (rev 03)
0000:00:1b.0 Class 0403: 8086:2668 (rev 04)
0000:00:1d.0 Class 0c03: 8086:2658 (rev 04)
0000:00:1d.1 Class 0c03: 8086:2659 (rev 04)
0000:00:1d.2 Class 0c03: 8086:265a (rev 04)
0000:00:1d.3 Class 0c03: 8086:265b (rev 04)
0000:00:1d.7 Class 0c03: 8086:265c (rev 04)
0000:00:1e.0 Class 0604: 8086:2448 (rev d4)
0000:00:1f.0 Class 0601: 8086:2641 (rev 04)
0000:00:1f.1 Class 0101: 8086:266f (rev 04)
0000:01:00.0 Class 0200: 11ab:4320 (rev 13)
0000:01:01.0 Class 0607: 1180:0476 (rev b3)
0000:01:01.1 Class 0c00: 1180:0552 (rev 08)
0000:01:01.2 Class 0805: 1180:0822 (rev 17)
0000:01:01.3 Class 0880: 1180:0592 (rev 08)
0000:01:01.4 Class 0880: 1180:0852 (rev 03)
0000:01:02.0 Class 0280: 8086:4220 (rev 05)
0000:03:00.0 Class 0300: 1002:3150
# lspci -v
0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML
Express Processor to DRAM Controller (rev 03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] #09 [2109]
0000:00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI
Express Root Port (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Bus: primary\0, secondary\x03, subordinate\x03, sec-latency=0
I/O behind bridge: 0000b000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: cff00000-dfefffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] #10 [0141]
0000:00:1b.0 Class 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) High Definition Audio Controller (rev 04)
Subsystem: ASUSTeK Computer Inc.: Unknown device 10c3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size\x16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrentUmA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] #10 [0091]
0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at e480 [size2]
0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at e800 [size2]
0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e880 [size2]
0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at ec00 [size2]
0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent75mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x01, subordinate\x02, sec-latency2
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 0000000060000000-0000000062f00000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface
Bridge (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) IDE Controller (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size\x16]
0000:01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller
(Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe9f8000 (32-bit, non-prefetchable) [size\x16K]
Region 1: I/O ports at a800 [size%6]
Expansion ROM at 62000000 [disabled] [size\x128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
0000:01:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe900000 (32-bit, non-prefetchable) [size=4K]
Bus: primary\x01, secondary\x02, subordinate\x02, sec-latency\x176
Memory window 0: 60000000-61fff000 (prefetchable)
Memory window 1: 64000000-65fff000
I/O window 0: 0000a000-0000a0ff
I/O window 1: 0000a400-0000a4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:01:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller
(rev 08) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 16
Region 0: Memory at fe9fd800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
0000:01:01.2 Class 0805: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host
Adapter (rev 17)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin C routed to IRQ 6
Region 0: Memory at fe9fe400 (32-bit, non-prefetchable) [size%6]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 08)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 6
Region 0: Memory at fe9fe800 (32-bit, non-prefetchable) [size%6]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev
03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 6
Region 0: Memory at fe9fec00 (32-bit, non-prefetchable) [size%6]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev
05)
Subsystem: Intel Corporation: Unknown device 2701
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 6000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe9ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
0000:03:00.0 VGA compatible controller: ATI Technologies Inc M24 1P [Radeon
Mobility X600] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1881
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d0000000 (32-bit, prefetchable) [size\x128M]
Region 1: I/O ports at d000 [size%6]
Region 2: Memory at feaf0000 (32-bit, non-prefetchable) [sizedK]
Expansion ROM at cff00000 [disabled] [size\x128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #10 [0001]
Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
# lspci -v -v -v
0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML
Express Processor to DRAM Controller (rev 03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] #09 [2109]
0000:00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI
Express Root Port (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Bus: primary\0, secondary\x03, subordinate\x03, sec-latency=0
I/O behind bridge: 0000b000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: cff00000-dfefffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] #10 [0141]
0000:00:1b.0 Class 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) High Definition Audio Controller (rev 04)
Subsystem: ASUSTeK Computer Inc.: Unknown device 10c3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size\x16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrentUmA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] #10 [0091]
0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at e480 [size2]
0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at e800 [size2]
0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e880 [size2]
0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at ec00 [size2]
0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent75mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x01, subordinate\x02, sec-latency2
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 0000000060000000-0000000062f00000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface
Bridge (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) IDE Controller (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size\x16]
0000:01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller
(Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe9f8000 (32-bit, non-prefetchable) [size\x16K]
Region 1: I/O ports at a800 [size%6]
Expansion ROM at 62000000 [disabled] [size\x128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
0000:01:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe900000 (32-bit, non-prefetchable) [size=4K]
Bus: primary\x01, secondary\x02, subordinate\x02, sec-latency\x176
Memory window 0: 60000000-61fff000 (prefetchable)
Memory window 1: 64000000-65fff000
I/O window 0: 0000a000-0000a0ff
I/O window 1: 0000a400-0000a4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:01:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller
(rev 08) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 16
Region 0: Memory at fe9fd800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
0000:01:01.2 Class 0805: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host
Adapter (rev 17)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin C routed to IRQ 6
Region 0: Memory at fe9fe400 (32-bit, non-prefetchable) [size%6]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 08)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 6
Region 0: Memory at fe9fe800 (32-bit, non-prefetchable) [size%6]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev
03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 1967
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 6
Region 0: Memory at fe9fec00 (32-bit, non-prefetchable) [size%6]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev
05)
Subsystem: Intel Corporation: Unknown device 2701
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 6000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe9ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
0000:03:00.0 VGA compatible controller: ATI Technologies Inc M24 1P [Radeon
Mobility X600] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1881
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d0000000 (32-bit, prefetchable) [size\x128M]
Region 1: I/O ports at d000 [size%6]
Region 2: Memory at feaf0000 (32-bit, non-prefetchable) [sizedK]
Expansion ROM at cff00000 [disabled] [size\x128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #10 [0001]
Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
0378-037a : parport0
037b-037f : parport0
03c0-03df : vesafb
03f6-03f6 : ide0
0680-068f : pnp 00:07
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0810-0815 : ACPI CPU throttle
0828-082f : GPE0_BLK
a000-afff : PCI Bus #01
a000-a0ff : PCI CardBus #02
a400-a4ff : PCI CardBus #02
a800-a8ff : 0000:01:00.0
a800-a8ff : SysKonnect SK-98xx
b000-dfff : PCI Bus #03
d000-d0ff : 0000:03:00.0
e480-e49f : 0000:00:1d.0
e480-e49f : uhci_hcd
e800-e81f : 0000:00:1d.1
e800-e81f : uhci_hcd
e880-e89f : 0000:00:1d.2
e880-e89f : uhci_hcd
ec00-ec1f : 0000:00:1d.3
ec00-ec1f : uhci_hcd
ffa0-ffaf : 0000:00:1f.1
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
# cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cffff : Video ROM
000f0000-000fffff : System ROM
00100000-5ffbffff : System RAM
00100000-003b9e55 : Kernel code
003b9e56-004aa3e7 : Kernel data
5ffc0000-5ffcefff : ACPI Tables
5ffcf000-5fffffff : ACPI Non-volatile Storage
60000000-62ffffff : PCI Bus #01
60000000-61ffffff : PCI CardBus #02
62000000-6201ffff : 0000:01:00.0
64000000-65ffffff : PCI CardBus #02
cff00000-dfefffff : PCI Bus #03
cff00000-cff1ffff : 0000:03:00.0
d0000000-d7ffffff : 0000:03:00.0
d0000000-d3ffffff : vesafb
fe900000-fe9fffff : PCI Bus #01
fe900000-fe900fff : 0000:01:01.0
fe900000-fe900fff : yenta_socket
fe9f8000-fe9fbfff : 0000:01:00.0
fe9f8000-fe9fbfff : SysKonnect SK-98xx
fe9fd800-fe9fdfff : 0000:01:01.1
fe9fd800-fe9fdfff : ohci1394
fe9fe400-fe9fe4ff : 0000:01:01.2
fe9fe800-fe9fe8ff : 0000:01:01.3
fe9fec00-fe9fecff : 0000:01:01.4
fe9ff000-fe9fffff : 0000:01:02.0
fe9ff000-fe9fffff : ipw2200
fea00000-feafffff : PCI Bus #03
feaf0000-feafffff : 0000:03:00.0
febf8000-febfbfff : 0000:00:1b.0
febf8000-febfbfff : ICH HD audio
febffc00-febfffff : 0000:00:1d.7
febffc00-febfffff : ehci_hcd
fed14000-fed19fff : reserved
fed1c000-fed1ffff : reserved
ffb80000-ffffffff : reserved
Regards,
Michal
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.lm-sensors.org/pipermail/lm-sensors/attachments/20050922/23bedd82/attachment-0001.html
next prev parent reply other threads:[~2005-09-22 10:35 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-09-22 1:47 [lm-sensors] Asus Z80V/M6V i2c support Michał Mleczko
2005-09-22 8:12 ` Rudolf Marek
2005-09-22 10:35 ` Michał Mleczko [this message]
2005-09-23 21:39 ` Rudolf Marek
2005-09-24 1:48 ` Michał Mleczko
2005-09-24 12:53 ` Michał Mleczko
2005-09-24 20:40 ` Rudolf Marek
2005-09-24 20:45 ` Michał Mleczko
2005-09-24 21:48 ` Rudolf Marek
2005-09-24 23:19 ` Michał Mleczko
2005-09-25 0:07 ` Rudolf Marek
2005-09-27 15:24 ` Michał Mleczko
2005-09-27 23:34 ` Rudolf Marek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=318b1df00509220134f03337b@mail.gmail.com \
--to=michal.mleczko@gmail.com \
--cc=lm-sensors@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.