From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from mailserv2.iuinc.com (qmailr@mailserv2.iuinc.com [206.245.164.55]) by puffin.external.hp.com (8.8.7/8.8.7) with SMTP id SAA10914 for ; Sun, 14 Nov 1999 18:00:13 -0700 Sender: rbrad@mailserv2.iuinc.com Message-ID: <382F5B60.D215DB58@uswest.net> Date: Sun, 14 Nov 1999 18:01:20 -0700 From: Ryan Bradetich MIME-Version: 1.0 To: Alex deVries CC: paul_bame@hp.com, Parisc Linux Subject: Re: [parisc-linux] arch/parisc/kernel/realmode_setup.c Question References: Content-Type: text/plain; charset=us-ascii List-ID: Alex deVries wrote: > On Sun, 14 Nov 1999, Ryan Bradetich wrote: > > I have started working on getting the kernel to boot on the PA2.0 > > architecture again, and I see the you and others have been doing > > lots of work with the initialization code. (Nice job to everyone btw, > > the code is a lot easier to figure out for a newbie like me! :) > > Same here. > > > I am working on a C200+ which has the PA2.0 processor, so in the > > the following section of code it should give me an error during the > > BTLB initialization, but during the PDC_BTLB_INSERT pret is set > > to 0, so the check for non-PA1.1 architecture's fail. > > It's a bit unclear to me which processor is actually in there, but I > believe it's an 8000, so it and the firmware may in fact support > PDC_BTLB_INSERT, which means that the kernel might work properly. > > I have a C3000 which does *NOT* implement PDC_BTLB functions. > > It sounds like the error message is actually a bit misleading. > > Instead of: > > mprintf("Looks like there's no BTLB on this box, so it's > probably\n" > "either PA1.0 or PA2.0. In any case we're screwed for now\n"); > > it should be: > > "Looks like there's no BTLB on this box, so it's either a PA1.0 or a PA2.0 > that doesn't implement BTLBs" > > How far does it actually boot though? Same as always (their is just more console output before it hangs). Here is a cut/paste of the console messages from the serial console. Firmware Version 5.2 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State Coprocessor State I/D Cache --------- -------- --------------------- ----------------- ------------- 0 200 MHz Active Functional 512 KB/1 MB Central Bus Speed (in MHz) : 120 Available memory (bytes) : 268435456 Good memory required (bytes): 21827584 Primary boot path: FWSCSI.5.0 Alternate boot path: SESCSI.6.0 Console path: SERIAL_1.9600.8.none Keyboard path: PS2 CPU 0 WARNING: Self tests have been disabled as a result of FASTBOOT being enabled. To enable self tests, use the FASTBOOT command in the CONFIGURATION menu and reboot the system. WARNING: Memory has been initialized, but not tested as a result of FASTBOOT being enabled. To test memory, use the FASTBOOT command in the CONFIGURATION menu and reboot the system. Processor is booting from first available device. To discontinue, press any key within 10 seconds. Boot terminated. ------- Main Menu ------------------------------------------------------------- Command Description ------- ----------- BOot [PRI|ALT|] Boot from specified path PAth [PRI|ALT|CON|KEY] [] Display or modify a path SEArch [DIsplay|IPL] [] Search for boot devices COnfiguration [] Access Configuration menu/commands INformation [] Access Information menu/commands SERvice [] Access Service menu/commands DIsplay Redisplay the current menu HElp [|] Display help for menu or command RESET Restart the system ------- Main Menu: Enter command > bo lan Interact with IPL (Y, N, Q)?> n Booting... Network Station Address 0060b0-ea9875 System IP Address Server IP Address Boot IO Dependent Code (IODC) revision 2 HARD Booted. ------------------------------------------------------------------------------ PARISC/Linux Bootstrap Version 0.6 (non-interactive) By Helge Deller & Jason Eckhardt Built Sat Nov 13 17:17:38 MST 1999 by root@vega Reading parameters...done. Loading PA-RISC/Linux Kernel... SOM-Kernel: aux_header_location: 00000080 som : 00200080 exec_dfile: 000C8000 exec_dsize: 00082000 exec_dmem : C009A000 exec_tfile: 0003E000 exec_tsize: 00089008 exec_tmem : C0010000 Code at 0x00010000, size=0x00089008 Data at 0x0009A000, size=0x00082000 BSS at 0x0011C000. Transferring control to kernel. (At entry point 0x00010000) kernel(0x00148C80, 0x00504010, 0x00148C80, 0x00016640) Clear BSS 0x0011B048 --> 0x0013D690 Boot loader: PA/Linux, maybe PALO realmode_setup exiting ... At this point it hangs. Before, it always used to hang at: Transferring control to kernel. (At entry point 0x00010000) I still do not believe it ever successfully finished the rfi in head.S :( I still need to do some more research to verify this, but that is my gut feeling right now. Ryan Bradetich > > - Alex > > --------------------------------------------------------------------------- > To unsubscribe: send e-mail to parisc-linux-request@thepuffingroup.com with > `unsubscribe' as the subject.