From: Miles Lane <miles@megapathdsl.net>
To: Linux Kernel <linux-kernel@vger.kernel.org>
Subject: test13-pre4-ac2 -- The cardbus/pcmcia sockets no longer work with two devices present at boot time.
Date: Wed, 27 Dec 2000 00:42:14 -0800 [thread overview]
Message-ID: <3A49AB66.1000607@megapathdsl.net> (raw)
When I boot with the following inserted:
Socket 0:
product info: "3Com Corporation", "3CCFE575BT", "LAN Cardbus Card", "001"
manfid: 0x0101, 0x5157
function: 6 (network)
Socket 1:
product info: "PCMCIA ", "56K V.90 Fax Modem (LK) ", "FM560LK "
manfid: 0x0175, 0x0000
function: 2 (serial)
both sockets fail to set up properly and work.
Linux PCMCIA Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Enabling device 00:04.0 (0000 -> 0002)
PCI: Assigned IRQ 11 for device 00:04.0
PCI: Enabling device 00:04.1 (0000 -> 0002)
PCI: Assigned IRQ 11 for device 00:04.1
Intel PCIC probe: not found.
Yenta IRQ list 0698, PCI irq11
Socket status: 30000020
Yenta IRQ list 0698, PCI irq11
Socket status: 30000010
ACPI: System description tables not found
cs: socket c118b000 timed out during reset. Try increasing setup_delay.
cs: socket c118b800 timed out during reset. Try increasing setup_delay.
If I then run "cardctl eject" and then eject and reinsert the two
cards, the cards get set up correctly.
Note that I am not using the PCMCIA drivers. I am using Yenta
and its native development kernel friends. I am using modutils
2.3.22.
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 64 set
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=64M]
00:02.0 VGA compatible controller: Neomagic Corporation NM2160
[MagicGraph 128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 007e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 16 min, 255 max, 128 set
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fea00000 (32-bit, non-prefetchable) [size=2M]
Region 2: Memory at fed00000 (32-bit, non-prefetchable) [size=1M]
00:04.0 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 007e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168 set, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:04.1 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 007e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168 set, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=05, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at fcf0 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at fcc0 [disabled] [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
01:00.0 Ethernet controller: 3Com Corporation 3c575 [Megahertz] 10/100
LAN CardBus (rev 01)
Subsystem: 3Com Corporation: Unknown device 5b57
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 10 min, 5 max, 64 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000 [size=128]
Region 1: Memory at 10800000 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at 10800080 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10400000 [size=128K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
next reply other threads:[~2000-12-27 9:14 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-12-27 8:42 Miles Lane [this message]
2000-12-27 14:06 ` test13-pre4-ac2 -- The cardbus/pcmcia sockets no longer work with two devices present at boot time Jens Taprogge
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3A49AB66.1000607@megapathdsl.net \
--to=miles@megapathdsl.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.