From: I Lee Hetherington <ilh@sls.lcs.mit.edu>
To: Andrew Morton <andrewm@uow.edu.au>
Cc: Linux Kernel <linux-kernel@vger.kernel.org>,
Lee Hetherington <ilh@sls.lcs.mit.edu>
Subject: Re: Dell Precision 330 (Pentium 4, i850 chipset, 3c905c)
Date: Fri, 05 Jan 2001 09:59:39 -0500 [thread overview]
Message-ID: <3A55E15B.F39D6B87@sls.lcs.mit.edu> (raw)
In-Reply-To: <3A54E717.11A43B42@sls.lcs.mit.edu> <3A557D12.A5383794@uow.edu.au>
[-- Attachment #1: Type: text/plain, Size: 462 bytes --]
Andrew Morton wrote:
> Please do. The boot-time messages which come out of the driver
> would be interesting. It would help if you add `debug=7' to
> the 3c59x modprobe command line also.
OK. I've included dmesg output due to modprobe with debug=7 followed by ifup
(using pump -- problems persist with static IP as well), cat /proc/interrupts
showing no eth0, and ifconfig eth0.
Please let me know what else I can provide to help out.
--Lee Hetherington
[-- Attachment #2: dmesg --]
[-- Type: text/plain, Size: 6678 bytes --]
3c59x.c 15Sep00 Donald Becker and others http://www.scyld.com/network/vortex.html
eth0: 3Com 3c905C Tornado at 0xe880, 00:b0:d0:14:d2:b4, IRQ 11
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 1, status 24.
MII transceiver found at address 2, status 24.
Enabling bus-master transmits and whole-frame receives.
eth0: Initial media type Autonegotiate.
eth0: MII #1 status 0024, link partner capability 41e1, setting full-duplex.
eth0: vortex_open() InternalConfig 01800000.
eth0: vortex_open() irq 11 media status 8080.
eth0: Filling in the Rx ring.
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: Trying to send a boomerang packet, Tx index 0.
eth0: interrupt, status f201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status f201.
eth0: exiting interrupt, status f000.
eth0: Media selection timer tick happened, Autonegotiate.
eth0: MII transceiver has status 0020.
eth0: Media selection timer finished, Autonegotiate.
eth0: Trying to send a boomerang packet, Tx index 1.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: Trying to send a boomerang packet, Tx index 2.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 3.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 4.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 5.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 6.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 7.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 8.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 9.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 10.
eth0: interrupt, status e201, latency 2, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: vortex_close() status e000, Tx status 00.
eth0: vortex close stats: rx_nocopy 0 rx_copy 0 tx_queued 11 Rx pre-checksummed 0.
eth0: Initial media type Autonegotiate.
eth0: MII #1 status 0020, link partner capability 41e1, setting full-duplex.
eth0: vortex_open() InternalConfig 01800000.
eth0: vortex_open() irq 11 media status 8080.
eth0: Filling in the Rx ring.
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: Trying to send a boomerang packet, Tx index 0.
eth0: interrupt, status f201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status f201.
eth0: exiting interrupt, status f000.
eth0: Media selection timer tick happened, Autonegotiate.
eth0: MII transceiver has status 0020.
eth0: Media selection timer finished, Autonegotiate.
eth0: Trying to send a boomerang packet, Tx index 1.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: no boomerang interrupt pending
eth0: no boomerang interrupt pending
eth0: Trying to send a boomerang packet, Tx index 2.
eth0: interrupt, status e201, latency 2, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 3.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 4.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 5.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 6.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 7.
eth0: interrupt, status e201, latency 2, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 8.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 9.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: Trying to send a boomerang packet, Tx index 10.
eth0: interrupt, status e201, latency 3, cur_rx 0, dirty_rx 0
eth0: In interrupt loop, status e201.
eth0: exiting interrupt, status e000.
eth0: vortex_close() status e000, Tx status 00.
eth0: vortex close stats: rx_nocopy 0 rx_copy 0 tx_queued 22 Rx pre-checksummed 0.
[-- Attachment #3: interrupts --]
[-- Type: text/plain, Size: 358 bytes --]
CPU0
0: 20048 XT-PIC timer
1: 314 XT-PIC keyboard
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
11: 1660 XT-PIC aic7xxx
12: 0 XT-PIC PS/2 Mouse
13: 1 XT-PIC fpu
15: 7 XT-PIC ide1
NMI: 0
[-- Attachment #4: ifconfig --]
[-- Type: text/plain, Size: 307 bytes --]
eth0 Link encap:Ethernet HWaddr 00:B0:D0:14:D2:B4
BROADCAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:1 frame:0
TX packets:23 errors:0 dropped:0 overruns:0 carrier:1
collisions:0 txqueuelen:100
Interrupt:11 Base address:0xe880
next prev parent reply other threads:[~2001-01-05 15:00 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-01-04 21:11 Dell Precision 330 (Pentium 4, i850 chipset, 3c905c) I Lee Hetherington
2001-01-05 7:51 ` Andrew Morton
2001-01-05 14:59 ` I Lee Hetherington [this message]
2001-01-05 15:58 ` Andrew Morton
2001-01-05 15:55 ` I Lee Hetherington
2001-01-05 16:03 ` Andrew Morton
2001-01-05 16:01 ` I Lee Hetherington
2001-01-05 15:02 ` I Lee Hetherington
-- strict thread matches above, loose matches on Subject: below --
2001-01-04 22:09 Manfred
2001-01-04 22:13 ` I Lee Hetherington
2001-01-05 15:26 Jon Burgess
2001-01-05 15:33 ` I Lee Hetherington
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3A55E15B.F39D6B87@sls.lcs.mit.edu \
--to=ilh@sls.lcs.mit.edu \
--cc=andrewm@uow.edu.au \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.