* [parisc-linux] 0.9ser can't install on D210
@ 2001-06-05 10:23 jheumann
2001-06-05 12:47 ` Richard Hirst
2001-06-05 12:57 ` Thomas Bogendoerfer
0 siblings, 2 replies; 6+ messages in thread
From: jheumann @ 2001-06-05 10:23 UTC (permalink / raw)
To: parisc-linux
please help,
i can't load linux pa-risc 0.9seriell on my HP9000/D210.
Why?
(HP-UX 10.20 is running....)
Jan Heumann
jheumann@fonts.de
-----------------------------------------------------
Main Menu: Enter command > search
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type
----------- ----------------- -----------
P0 4.5 Random access media
P1 4.8 Random access media
P2 16/5.2 Random access media
P3 16/6.0 LAN Module
Main Menu: Enter command > boot p2
Interact with IPL (Y or N)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
IPL error: bad IPL checksum.
Error Reading IPL
Main Menu: Enter command > search
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type
----------- ----------------- -----------
P0 4.5 Random access media
P1 4.8 Random access media
P2 16/5.2 Random access media
P3 16/6.0 LAN Module
Main Menu: Enter command > boot p2
Interact with IPL (Y or N)?> y
Booting...
Boot IO Dependent Code (IODC) revision 1
IPL error: bad IPL checksum.
Error Reading IPL
--------------------------------------------------------
information all
PROCESSOR INFORMATION
HVERSION SVERSION CVERSION
Speed Model Model/Op (Revision)
--------- -------- -------- ----------
100 MHz 0x4840 0x0481 12
HSC Bus Speed (in MHz) : 33
Software ID (dec) : 2009187834
Software ID (hex) : 0x77c1c5fa
Software Capability : 0xf0
<Press any key to continue (q to quit)>
COPROCESSOR INFORMATION
Coprocessor Coprocessor Coprocessor
Model Revision State
----------- ----------- -------------
0x0000000d 1 Functional
CACHE INFORMATION
Instruction Cache Size Data Cache Size
----------------------- ---------------
128 KB 128 KB
<Press any key to continue (q to quit)>
MEMORY INFORMATION
Slot Card Size Amount Enabled
---- --------- --------------
0 64 MB 64 MB
1 64 MB 64 MB
2 64 MB 64 MB
3 64 MB 64 MB
4 64 MB 64 MB
5 64 MB 64 MB
Physical Memory: 384 MB (0x18000000)
Configured Memory: 384 MB (0x18000000)
<Press any key to continue (q to quit)>
I/O MODULE INFORMATION
IODC
IODC
Path (dec) Type Slot Mod HVERSION SVERSION Vers
Dep
---- ---- ---- --- -------- ---------- ------
------
4 A DMA I/O 1 0 0x0131 0x00008980 0x07
0x00
16 Bus Adapter 4 0 0x02e0 0x00008100 0x00
0x00
16/4 Built-in RS232 1 0 0x02e0 0x00008c00 0x01
0x00
16/5 Built-in SE SCSI 1 1 0x02e0 0x00008200 0x01
0x00
16/6 Built-in LAN 1 2 0x02e0 0x00008a00 0x02
0x00
16/0 Built-in Parallel 0 0 0x02e0 0x00007400 0x00
0x00
16/7 Built-in Keyboard 1 3 0x02e0 0x00008400 0x00
0x00
16/8 Built-in Mouse 2 0 0x02e0 0x00008400 0x00
0x00
20 Bus Adapter 5 0 0x0300 0x00008e00 0x00
0x00
20/2 RS232 Port 0 2 0x0300 0x00008c00 0x01
0x00
20/5 Bus Adapter 1 1 0x0300 0x00009000 0x00
0x00
<Press any key to continue (q to quit)>
Hot Swap module is present.
EISA Cards
Path Type EISA ID
---- ---- -------
20/5/1 EISA card 0x25d00400
20/5/2 EISA slot is empty
20/5/3 EISA slot is empty
20/5/4 EISA slot is empty
<Press any key to continue (q to quit)>
BOOT INFORMATION
Autoboot: ON
Autosearch: ON
Fastboot: OFF
Primary boot path: 4.8 (dec)
04.8 (hex)
Alternate boot path: 16/5.2 (dec)
10/05.2 (hex)
Console path: 16/4.0 (dec)
10/04.0 (hex)
Keyboard path: 16/7.0 (dec)
10/07.0 (hex)
LAN Station Address: 080009-af13c8
Mon Jan 5 21:15:36 GMT 1970 (19:70:01:05:21:15:36)
<Press any key to continue (q to quit)>
FIRMWARE INFORMATION
Firmware Version: 36.34
CHIP REVISIONS
Module Revision
------ --------
System Board 0
Processor Board 2
PA 7100LC 12
Firmware 20
Fast/Wide SCSI Board 1
Multifunction I/O Controller 0
EISA Interface 0
<Press any key to continue (q to quit)>
WARNINGS
No warnings to report.
Information Menu: Enter command >
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [parisc-linux] 0.9ser can't install on D210
2001-06-05 10:23 [parisc-linux] 0.9ser can't install on D210 jheumann
@ 2001-06-05 12:47 ` Richard Hirst
2001-06-05 13:00 ` Michael S.Zick
2001-06-05 12:57 ` Thomas Bogendoerfer
1 sibling, 1 reply; 6+ messages in thread
From: Richard Hirst @ 2001-06-05 12:47 UTC (permalink / raw)
To: jheumann; +Cc: parisc-linux
On Tue, Jun 05, 2001 at 12:23:14PM +0200, jheumann@fonts.de wrote:
> please help,
>
> i can't load linux pa-risc 0.9seriell on my HP9000/D210.
> Why?
You will see from <http://parisc-linux.org/release-0.9/systems.html>
that D series machines have not been tested. However, your problem
looks more like trouble reading the CD. Can you mount the CD on some
other system and see the contents, just to check the CD is burned
properly?
Alternatively you could try a network boot, as described in the
README on the CD.
Richard
>
> (HP-UX 10.20 is running....)
>
> Jan Heumann
> jheumann@fonts.de
> -----------------------------------------------------
> Main Menu: Enter command > search
>
> Searching for potential boot device(s)...
> This may take several minutes.
>
> To discontinue search, press any key (termination may not be immediate).
>
>
>
> Path Number Device Path (dec) Device Type
> ----------- ----------------- -----------
> P0 4.5 Random access media
> P1 4.8 Random access media
> P2 16/5.2 Random access media
> P3 16/6.0 LAN Module
>
>
> Main Menu: Enter command > boot p2
> Interact with IPL (Y or N)?> n
>
> Booting...
> Boot IO Dependent Code (IODC) revision 1
>
> IPL error: bad IPL checksum.
>
> Error Reading IPL
>
> Main Menu: Enter command > search
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [parisc-linux] 0.9ser can't install on D210
2001-06-05 10:23 [parisc-linux] 0.9ser can't install on D210 jheumann
2001-06-05 12:47 ` Richard Hirst
@ 2001-06-05 12:57 ` Thomas Bogendoerfer
2001-06-05 21:04 ` Thomas Bogendoerfer
1 sibling, 1 reply; 6+ messages in thread
From: Thomas Bogendoerfer @ 2001-06-05 12:57 UTC (permalink / raw)
To: jheumann; +Cc: parisc-linux
On Tue, Jun 05, 2001 at 12:23:14PM +0200, jheumann@fonts.de wrote:
> Booting...
> Boot IO Dependent Code (IODC) revision 1
>
> IPL error: bad IPL checksum.
>
> Error Reading IPL
did you use cdrecord -isosize to burn the CD ? I have the same problem and
that's the only option, which I probably haven't used, when burning the
0.5 ISO. I'll try to burn a cd without using -isosize, when I get home
this evening.
Thomas.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [parisc-linux] 0.9ser can't install on D210
2001-06-05 12:47 ` Richard Hirst
@ 2001-06-05 13:00 ` Michael S.Zick
0 siblings, 0 replies; 6+ messages in thread
From: Michael S.Zick @ 2001-06-05 13:00 UTC (permalink / raw)
To: jheumann; +Cc: parisc-linux, parisc-linux, debian-hppa
All -
OR, you might:
$>gunzip whatever.CD.ISO.gz
#>losetup /dev/loop0 ${whatever_path}/watever.CD.ISO
#>$mount -r -t iso9660 /dev/loop0 /somewhere
now you can browse the CD image to your hearts content.
also you can mount upto ten of these things (loop0-loop9) at
the same time.
Of course, you did build your kernel with the "loop device" and
"iso9660 filesystem support" didn't you?
PS: You can use similar commands to browse (and modify) your
ramdisk.bin files.
Mike
On Tue, 05 Jun 2001, Richard Hirst wrote:
> On Tue, Jun 05, 2001 at 12:23:14PM +0200, jheumann@fonts.de wrote:
> > please help,
> >=20
> > i can't load linux pa-risc 0.9seriell on my HP9000/D210.
> > Why?
>=20
> You will see from <http://parisc-linux.org/release-0.9/systems.html>
> that D series machines have not been tested. However, your problem
> looks more like trouble reading the CD. Can you mount the CD on some
> other system and see the contents, just to check the CD is burned
> properly?
>=20
> Alternatively you could try a network boot, as described in the
> README on the CD.
>=20
> Richard
>=20
>=20
> >=20
> > (HP-UX 10.20 is running....)
> >=20
> > Jan Heumann
> > jheumann@fonts.de
> > -----------------------------------------------------
> > Main Menu: Enter command > search
> >=20
> > Searching for potential boot device(s)...
> > This may take several minutes.
> >=20
> > To discontinue search, press any key (termination may not be immediat=
e).
> >=20
> >=20
> >=20
> > Path Number Device Path (dec) Device Type
> > ----------- ----------------- -----------
> > P0 4.5 Random access media
> > P1 4.8 Random access media
> > P2 16/5.2 Random access media
> > P3 16/6.0 LAN Module
> >=20
> >=20
> > Main Menu: Enter command > boot p2
> > Interact with IPL (Y or N)?> n
> >=20
> > Booting...
> > Boot IO Dependent Code (IODC) revision 1
> >=20
> > IPL error: bad IPL checksum.
> >=20
> > Error Reading IPL
> >=20
> > Main Menu: Enter command > search
>=20
>=20
> _______________________________________________
> parisc-linux mailing list
> parisc-linux@lists.parisc-linux.org
> http://lists.parisc-linux.org/cgi-bin/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [parisc-linux] 0.9ser can't install on D210
2001-06-05 12:57 ` Thomas Bogendoerfer
@ 2001-06-05 21:04 ` Thomas Bogendoerfer
2001-06-11 13:21 ` jheumann
0 siblings, 1 reply; 6+ messages in thread
From: Thomas Bogendoerfer @ 2001-06-05 21:04 UTC (permalink / raw)
To: jheumann; +Cc: parisc-linux
On Tue, Jun 05, 2001 at 02:57:31PM +0200, Thomas Bogendoerfer wrote:
> On Tue, Jun 05, 2001 at 12:23:14PM +0200, jheumann@fonts.de wrote:
> > Booting...
> > Boot IO Dependent Code (IODC) revision 1
> >
> > IPL error: bad IPL checksum.
> >
> > Error Reading IPL
>
> did you use cdrecord -isosize to burn the CD ? I have the same problem and
> that's the only option, which I probably haven't used, when burning the
> 0.5 ISO. I'll try to burn a cd without using -isosize, when I get home
> this evening.
ok, without -isosize the CDs are working perfect. I've diffed the broken
CDs against the images and there are differences in the first sector.
I'm using cdrecord 1.8.1 just for the record.
Thomas.
--
Crap can work. Given enough thrust pigs will fly, but it's not necessary a
good idea. [ Alexander Viro on linux-kernel ]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [parisc-linux] 0.9ser can't install on D210
2001-06-05 21:04 ` Thomas Bogendoerfer
@ 2001-06-11 13:21 ` jheumann
0 siblings, 0 replies; 6+ messages in thread
From: jheumann @ 2001-06-11 13:21 UTC (permalink / raw)
To: parisc-linux
the problem is over.
i have probe the iso image 0.9ser from ESIEE. this will not work on my D210 and
712-60.
i have download the image from
http://puffin.external.hp.com/pub/parisc/cd-images/palinux-0.9-32serial.iso.gz
and this work.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2001-06-11 17:50 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2001-06-05 10:23 [parisc-linux] 0.9ser can't install on D210 jheumann
2001-06-05 12:47 ` Richard Hirst
2001-06-05 13:00 ` Michael S.Zick
2001-06-05 12:57 ` Thomas Bogendoerfer
2001-06-05 21:04 ` Thomas Bogendoerfer
2001-06-11 13:21 ` jheumann
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.