From: Brian Strand <bstrand@switchmanagement.com>
To: linux-kernel@vger.kernel.org
Subject: Re: 3ware: no cards found in 2.2.19, cards found in 2.4.x
Date: Sat, 25 Aug 2001 04:56:03 -0700 [thread overview]
Message-ID: <3B879253.2010400@switchmanagement.com> (raw)
In-Reply-To: <E15aKzT-0006BX-00@the-village.bc.nu>
Alan Cox wrote:
>Im using one with 2.2.18 fine. Is your bios set for pnp os ?
>
>
I modified the setting from "No PNP OS" to "PNP OS", with identical
results (card not found). Could there be a conflict with another card
only under 2.2.19? Here is an lspci -vvv (from the 2.4.4-14 kernel):
00:07.0 RAID bus controller: 3ware Inc 3ware ATA-RAID (rev 12)
Subsystem: 3ware Inc 3ware ATA-RAID
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2250ns min)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 2420 [size=16]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:08.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
53c810 (rev 23)
Subsystem: Symbios Logic Inc. (formerly NCR) 8100S
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 58
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at d0001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 VGA compatible controller: Cirrus Logic GD 5480 (rev 23)
(prog-if 00 [VGA])
Subsystem: Unknown device 3e3e:003e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 2500ns max)
Region 0: Memory at d2000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=32K]
00:0b.0 PIC: Intel Corporation 683053 Programmable Interrupt Device
(prog-if 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (2000ns min, 2000ns max)
00:0c.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:0c.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 2430 [size=16]
00:0c.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 54
Region 4: I/O ports at 2400 [size=32]
00:0c.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:10.0 Host bridge: Intel Corporation 450NX - 82451NX Memory & I/O
Controller (rev 03)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:12.0 Host bridge: Intel Corporation 450NX - 82454NX/84460GX PCI
Expander Bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 128, cache line size 08
00:13.0 Host bridge: Intel Corporation 450NX - 82454NX/84460GX PCI
Expander Bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 128, cache line size 08
01:01.0 SCSI storage controller: Adaptec AHA-2940U2/W
Subsystem: Adaptec: Unknown device a180
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (9750ns min, 6250ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
BIST result: 00
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at d4004000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:02.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, cache line size 08
Bus: primary=01, secondary=02, subordinate=02, sec-latency=68
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d4100000-d43fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000eff00000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
01:03.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
53c896 (rev 01)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 57
Region 0: I/O ports at 3400 [size=256]
Region 1: Memory at d4005000 (64-bit, non-prefetchable) [size=1K]
Region 3: Memory at d4000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:03.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
53c896 (rev 01)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin B routed to IRQ 56
Region 0: I/O ports at 3800 [size=256]
Region 1: Memory at d4005400 (64-bit, non-prefetchable) [size=1K]
Region 3: Memory at d4002000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 64)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 3c00 [size=128]
Region 1: Memory at d4005800 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:03.0 Memory controller: Distributed Processing Technology Domino RAID
Engine (rev 02)
Subsystem: Distributed Processing Technology Domino RAID Engine
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B+
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 50
BIST result: 00
Region 0: Memory at d4100000 (32-bit, non-prefetchable) [size=64K]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
02:04.0 I2O: Distributed Processing Technology SmartRAID V Controller
(rev 03) (prog-if 01)
Subsystem: Distributed Processing Technology: Unknown device 50c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns min, 250ns max), cache line size 08
Interrupt: pin A routed to IRQ 20
BIST result: 00
Region 0: Memory at d4200000 (32-bit, non-prefetchable) [size=2M]
Region 1: I/O ports at 4000 [size=256]
Expansion ROM at 00090000 [disabled] [size=32K]
next parent reply other threads:[~2001-08-25 11:56 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <E15aKzT-0006BX-00@the-village.bc.nu>
2001-08-25 11:56 ` Brian Strand [this message]
2001-08-24 5:36 3ware: no cards found in 2.2.19, cards found in 2.4.x Brian Strand
2001-08-24 7:01 ` David Ford
2001-08-24 16:10 ` Brian Strand
2001-08-24 16:34 ` David Ford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3B879253.2010400@switchmanagement.com \
--to=bstrand@switchmanagement.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.