diff for duplicates of <3D530222.7040303@redswitch.com> diff --git a/a/1.txt b/N1/1.txt index b221c49..ec3ed3d 100644 --- a/a/1.txt +++ b/N1/1.txt @@ -1,12 +1,13 @@ + Hi *, -I'm trying to enable MTD and JFFS2 on an Intel 28F160F3 chip but have +I'm trying to enable MTD and JFFS2 on an Intel 28F160F3 chip but have some problems. -The basic problem is what the physical start address of flash mapping -is? While on PPCBoot, I got flash information using command 'flinfo'. -The start address is FFE00000. Is this address the one used to configure -CFI flash device in physical memeory map? I tried using this address but +The basic problem is what the physical start address of flash mapping +is? While on PPCBoot, I got flash information using command 'flinfo'. +The start address is FFE00000. Is this address the one used to configure +CFI flash device in physical memeory map? I tried using this address but 'physmap' couldn't find flash device. -----------------clip----------------------------------------- @@ -31,8 +32,11 @@ Bank # 1: INTEL 28F160F3 (16 Mbit, top boot sector) => -----------------clip----------------------------------------- -I haven't dived into the routine 'do_cfi_probe()' yet since I'm not sure -if the start address I specified is correct. Any help is greatly +I haven't dived into the routine 'do_cfi_probe()' yet since I'm not sure +if the start address I specified is correct. Any help is greatly appreciated. - Shawn. + + +** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/ diff --git a/a/content_digest b/N1/content_digest index a3d0628..dc2ed39 100644 --- a/a/content_digest +++ b/N1/content_digest @@ -5,15 +5,16 @@ " linuxppc-embedded@lists.linuxppc.org\0" "\00:1\0" "b\0" + "\n" "Hi *,\n" "\n" - "I'm trying to enable MTD and JFFS2 on an Intel 28F160F3 chip but have \n" + "I'm trying to enable MTD and JFFS2 on an Intel 28F160F3 chip but have\n" "some problems.\n" "\n" - "The basic problem is what the physical start address of flash mapping \n" - "is? While on PPCBoot, I got flash information using command 'flinfo'. \n" - "The start address is FFE00000. Is this address the one used to configure \n" - "CFI flash device in physical memeory map? I tried using this address but \n" + "The basic problem is what the physical start address of flash mapping\n" + "is? While on PPCBoot, I got flash information using command 'flinfo'.\n" + "The start address is FFE00000. Is this address the one used to configure\n" + "CFI flash device in physical memeory map? I tried using this address but\n" " 'physmap' couldn't find flash device.\n" "\n" "-----------------clip-----------------------------------------\n" @@ -38,10 +39,13 @@ "=>\n" "-----------------clip-----------------------------------------\n" "\n" - "I haven't dived into the routine 'do_cfi_probe()' yet since I'm not sure \n" - "if the start address I specified is correct. Any help is greatly \n" + "I haven't dived into the routine 'do_cfi_probe()' yet since I'm not sure\n" + "if the start address I specified is correct. Any help is greatly\n" "appreciated.\n" "\n" - - Shawn. + "- Shawn.\n" + "\n" + "\n" + ** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/ -24e70cc6e3ebfa552d7f8b763a7fa9cf6e1b826d64bc574851dafdd960c76a76 +e2ebb07bb610f8abd4c65d4041350d304f07831bc83cc0254e5a65e80239ba7c
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.