From: Michael Madore <mmadore-JChM1cqIHx8AvxtiuMwx3w@public.gmane.org>
To: "Brown, Len" <len.brown-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Cc: acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
Subject: Re: APIC not enabled on Opteron
Date: Mon, 25 Aug 2003 14:30:23 -0700 [thread overview]
Message-ID: <3F4A7FEF.9010405@aslab.com> (raw)
In-Reply-To: <BF1FE1855350A0479097B3A0D2A80EE009FCC4-N2PTB0HCzHJF3Yvz3xaN/VDQ4js95KgL@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 1049 bytes --]
Brown, Len wrote:
>Michael,
>I don't see the log attachment.
>
>In any case, 2.6-test3 is missing a couple of acpi interrupt changes
>that are now in 2.4.22-rc2; and I'll be getting those changes ready for
>2.6 shortly.
>
>In the mean-time, if you want the APIC more than you want ACPI, you can
>boot with acpi=off for now and the legacy code will configure your
>interrupts.
>
>Cheers,
>-Len
>
>
>
Hi Len,
Sorry about that. Here are the kernel messages, this time from the new
2.4.22 and booted with acpi=off. In this case, I still only get 16 irqs.
CPU0
0: 120189 IO-APIC-edge timer
1: 97 IO-APIC-edge keyboard
2: 0 XT-PIC cascade
5: 4 IO-APIC-edge ehci_hcd
8: 1 IO-APIC-edge rtc
11: 5203 IO-APIC-edge usb-ohci, ohci1394, eth0
12: 0 IO-APIC-edge PS/2 Mouse
14: 6706 IO-APIC-edge ide0
15: 1 IO-APIC-edge ide1
NMI: 0
LOC: 120129
ERR: 0
MIS: 0
Thanks for your advice
Mike
[-- Attachment #2: apic.log --]
[-- Type: text/plain, Size: 6096 bytes --]
Linux version 2.4.22 (root-+BuE2envYkR9v3KYkwAI1Vjtk6BVbLCt@public.gmane.org) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 SMP Mon Aug 25 16:16:19 EDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e7000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dbf40000 (usable)
BIOS-e820: 00000000dbf40000 - 00000000dbf50000 (ACPI data)
BIOS-e820: 00000000dbf50000 - 00000000dc000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
2623MB HIGHMEM available.
896MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 900928
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 671552 pages.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: TEMPLATE Product ID: SK8N APIC at: 0xFEE00000
Processor #0 Unknown CPU [15:5] APIC version 16
I/O APIC #1 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: auto BOOT_IMAGE=2.4.22 ro BOOT_FILE=/boot/vmlinuz-2.4.22 root=/dev/hda2 acpi=off
Initializing CPU#0
Detected 1399.998 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2791.83 BogoMIPS
Memory: 3557628k/3603712k available (1890k kernel code, 45696k reserved, 657k data, 136k init, 2686208k highmem)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 262144 (order: 8, 1048576 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: Common caps: 078bfbff e1d3fbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch-r1x6VkxMR+00zabcByZE4g@public.gmane.org)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: Common caps: 078bfbff e1d3fbff 00000000 00000000
CPU0: AMD Opteron(tm) Processor 240 stepping 01
per-CPU timeslice cutoff: 2927.40 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 16.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 01000000
....... : arbitration: 01
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1399.9860 MHz.
..... host bus clock speed is 199.9980 MHz.
cpu: 0, clocks: 1999980, slice: 999990
CPU0<T0:1999968,T1:999968,D:10,S:999990,C:1999980>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
ACPI: Subsystem revision 20030813
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [10de/00d0] at 00:01.0
next prev parent reply other threads:[~2003-08-25 21:30 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-08-23 2:29 APIC not enabled on Opteron Brown, Len
[not found] ` <BF1FE1855350A0479097B3A0D2A80EE009FCC4-N2PTB0HCzHJF3Yvz3xaN/VDQ4js95KgL@public.gmane.org>
2003-08-25 21:30 ` Michael Madore [this message]
2003-08-25 22:04 ` Michael Madore
-- strict thread matches above, loose matches on Subject: below --
2003-08-22 23:31 Michael Madore
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3F4A7FEF.9010405@aslab.com \
--to=mmadore-jchm1cqihx8avxtiumwx3w@public.gmane.org \
--cc=acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
--cc=len.brown-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.