From: jtholmes <jtholmes@jtholmes.com>
To: linux-kernel@vger.kernel.org, jtholmesjr@comcast.net
Subject: irq 11: nobody cared! is back
Date: Fri, 19 Sep 2003 09:36:49 -0400 [thread overview]
Message-ID: <3F6B0671.1070603@jtholmes.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 28717 bytes --]
I don't take the Distribution, and don't need email copy of
answer, just answer in LKML and I will see it.
If I knew how to turn on more debugging I would gladly do so
as I need to figure out the Kernel debugging scheme.
Problem Description
After loading Module uhci-hcd
USB Optical Mouse light shuts off and irq 11: is disabled.
Steps to reproduce problem
Boot Linux
modprobe -v usbcore
modprobe -v uhci-hcd
Mouse goes away, irq 11: disabled
At this point Everything else appears to work ok
ver_linux output
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux jtlin60 2.6.0-test5 #9 Fri Sep 19 00:16:44 EDT 2003 i686 unknown
Gnu C 2.96
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
e2fsprogs 1.27
reiserfsprogs 3.x.0j
pcmcia-cs 3.2.5
quota-tools 3.01.
PPP 2.4.1
isdn4k-utils 3.1pre1
nfs-utils 0.3.3
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Console-tools 0.3.3
Sh-utils 2.0.11
Modules Loaded uhci_hcd usbcore binfmt_misc ds yenta_socket pcmcia_core parport_pc parport
lsmod immed after boot up
Module Size Used by
binfmt_misc 7976 0
ds 10400 4
yenta_socket 13184 1
pcmcia_core 55168 2 ds,yenta_socket
parport_pc 22600 0
parport 35232 1 parport_pc
lsmod after load of usbcore and uhci-hcd
Module Size Used by
uhci_hcd 27464 0
usbcore 96660 3 uhci_hcd
binfmt_misc 7976 0
ds 10400 4
yenta_socket 13184 1
pcmcia_core 55168 2 ds,yenta_socket
parport_pc 22600 0
parport 35232 1 parport_pc
/usr/src/linux/.config
Very large, see attachments
/var/log/messages
Sep 19 08:46:44 jtlin60 syslogd 1.4.1: restart.
Sep 19 08:46:44 jtlin60 syslog: syslogd startup succeeded
Sep 19 08:46:45 jtlin60 kernel: klogd 1.4.1, log source = /proc/kmsg started.
Sep 19 08:46:45 jtlin60 kernel: Linux version 2.6.0-test5 (root@jtlin60) (gcc version 2.95.3 20010315 (release)) #9 Fri Sep 19 00:16:44 EDT 2003
Sep 19 08:46:45 jtlin60 kernel: Video mode to be used for restore is f00
Sep 19 08:46:45 jtlin60 kernel: BIOS-provided physical RAM map:
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 00000000000e8000 - 00000000000ec000 (reserved)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 0000000000100000 - 000000000bfe0000 (usable)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 000000000bfe0000 - 000000000bff0000 (ACPI data)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 000000000bff0000 - 000000000c000000 (reserved)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 00000000100a0000 - 00000000100b6e00 (reserved)
Sep 19 08:46:45 jtlin60 syslog: klogd startup succeeded
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 00000000100b6e00 - 00000000100b7000 (ACPI NVS)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 00000000100b7000 - 0000000010100000 (reserved)
Sep 19 08:46:45 jtlin60 kernel: BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Sep 19 08:46:45 jtlin60 kernel: 0MB HIGHMEM available.
Sep 19 08:46:45 jtlin60 kernel: 191MB LOWMEM available.
Sep 19 08:46:45 jtlin60 kernel: On node 0 totalpages: 49120
Sep 19 08:46:45 jtlin60 kernel: DMA zone: 4096 pages, LIFO batch:1
Sep 19 08:46:45 jtlin60 kernel: Normal zone: 45024 pages, LIFO batch:10
Sep 19 08:46:45 jtlin60 portmap: portmap startup succeeded
Sep 19 08:46:45 jtlin60 kernel: HighMem zone: 0 pages, LIFO batch:1
Sep 19 08:46:45 jtlin60 kernel: DMI 2.3 present.
Sep 19 08:46:45 jtlin60 kernel: Building zonelist for node : 0
Sep 19 08:46:45 jtlin60 kernel: Kernel command line: auto BOOT_IMAGE=l6_test5 ro root=301 BOOT_FILE=/boot/vmlinuz-2.6.0-test5
Sep 19 08:46:45 jtlin60 kernel: Initializing CPU#0
Sep 19 08:46:45 jtlin60 kernel: PID hash table entries: 1024 (order 10: 8192 bytes)
Sep 19 08:46:45 jtlin60 kernel: Detected 361.392 MHz processor.
Sep 19 08:46:45 jtlin60 nfslock: rpc.statd startup succeeded
Sep 19 08:46:45 jtlin60 rpc.statd[477]: Version 0.3.3 Starting
Sep 19 08:46:45 jtlin60 kernel: Console: colour VGA+ 80x25
Sep 19 08:46:45 jtlin60 kernel: Memory: 191524k/196480k available (1296k kernel code, 4304k reserved, 691k data, 112k init, 0k highmem)
Sep 19 08:46:45 jtlin60 kernel: Calibrating delay loop... 692.22 BogoMIPS
Sep 19 08:46:45 jtlin60 kernel: Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Sep 19 08:46:45 jtlin60 kernel: Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Sep 19 08:46:45 jtlin60 keytable: Loading keymap: succeeded
Sep 19 08:46:46 jtlin60 kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Sep 19 08:46:46 jtlin60 kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Sep 19 08:46:46 jtlin60 kernel: CPU: L2 cache: 256K
Sep 19 08:46:46 jtlin60 kernel: Intel machine check architecture supported.
Sep 19 08:46:46 jtlin60 kernel: Intel machine check reporting enabled on CPU#0.
Sep 19 08:46:46 jtlin60 kernel: CPU: Intel Pentium III (Coppermine) stepping 06
Sep 19 08:46:46 jtlin60 kernel: Enabling fast FPU save and restore... done.
Sep 19 08:46:46 jtlin60 keytable: Loading system font: succeeded
Sep 19 08:46:46 jtlin60 kernel: Enabling unmasked SIMD FPU exception support... done.
Sep 19 08:46:46 jtlin60 kernel: Checking 'hlt' instruction... OK.
Sep 19 08:46:46 jtlin60 kernel: Checking for popad bug... OK.
Sep 19 08:46:46 jtlin60 kernel: POSIX conformance testing by UNIFIX
Sep 19 08:46:46 jtlin60 kernel: NET: Registered protocol family 16
Sep 19 08:46:46 jtlin60 kernel: EISA bus registered
Sep 19 08:46:46 jtlin60 kernel: PCI: PCI BIOS revision 2.10 entry at 0xfee03, last bus=21
Sep 19 08:46:46 jtlin60 kernel: PCI: Using configuration type 1
Sep 19 08:46:46 jtlin60 kernel: mtrr: v2.0 (20020519)
Sep 19 08:46:46 jtlin60 random: Initializing random number generator: succeeded
Sep 19 08:46:46 jtlin60 kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Sep 19 08:46:46 jtlin60 kernel: PCI: Probing PCI hardware
Sep 19 08:46:46 jtlin60 kernel: PCI: Probing PCI hardware (bus 00)
Sep 19 08:46:46 jtlin60 kernel: PCI: Using IRQ router PIIX [8086/7110] at 0000:00:05.0
Sep 19 08:46:46 jtlin60 kernel: PCI: IRQ 0 for device 0000:00:0b.0 doesn't match PIRQ mask - try pci=usepirqmask
Sep 19 08:46:46 jtlin60 kernel: PCI: Found IRQ 11 for device 0000:00:0b.0
Sep 19 08:46:46 jtlin60 kernel: PCI: IRQ 0 for device 0000:00:0b.1 doesn't match PIRQ mask - try pci=usepirqmask
Sep 19 08:46:46 jtlin60 kernel: PCI: Found IRQ 11 for device 0000:00:0b.1
Sep 19 08:46:46 jtlin60 kernel: apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
Sep 19 08:46:46 jtlin60 kernel: VFS: Disk quotas dquot_6.5.1
Sep 19 08:46:46 jtlin60 kernel: Initializing Cryptographic API
Sep 19 08:46:46 jtlin60 kernel: Limiting direct PCI/PCI transfers.
Sep 19 08:46:43 jtlin60 sysctl: kernel.core_uses_pid = 1
Sep 19 08:46:46 jtlin60 kernel: isapnp: Scanning for PnP cards...
Sep 19 08:46:43 jtlin60 network: Setting network parameters: succeeded
Sep 19 08:46:46 jtlin60 kernel: isapnp: No Plug & Play device found
Sep 19 08:46:46 jtlin60 kernel: Using anticipatory scheduling io scheduler
Sep 19 08:46:46 jtlin60 kernel: Floppy drive(s): fd0 is 1.44M
Sep 19 08:46:46 jtlin60 kernel: FDC 0 is a post-1991 82077
Sep 19 08:46:46 jtlin60 kernel: loop: loaded (max 8 devices)
Sep 19 08:46:46 jtlin60 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Sep 19 08:46:46 jtlin60 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Sep 19 08:46:46 jtlin60 kernel: PIIX4: IDE controller at PCI slot 0000:00:05.1
Sep 19 08:46:46 jtlin60 kernel: PIIX4: chipset revision 1
Sep 19 08:46:46 jtlin60 kernel: PIIX4: not 100%% native mode: will probe irqs later
Sep 19 08:46:46 jtlin60 kernel: ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:pio
Sep 19 08:46:46 jtlin60 kernel: ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:DMA, hdd:pio
Sep 19 08:46:46 jtlin60 kernel: hda: TOSHIBA MK2018GAP, ATA DISK drive
Sep 19 08:46:46 jtlin60 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Sep 19 08:46:46 jtlin60 kernel: hdc: TOSHIBA DVD-ROM SD-C2402, ATAPI CD/DVD-ROM drive
Sep 19 08:46:46 jtlin60 kernel: ide1 at 0x170-0x177,0x376 on irq 15
Sep 19 08:46:46 jtlin60 kernel: hda: max request size: 128KiB
Sep 19 08:46:46 jtlin60 kernel: hda: 39070080 sectors (20003 MB), CHS=38760/16/63, UDMA(33)
Sep 19 08:46:46 jtlin60 kernel: hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
Sep 19 08:46:46 jtlin60 kernel: ide-floppy driver 0.99.newide
Sep 19 08:46:46 jtlin60 kernel: mice: PS/2 mouse device common for all mice
Sep 19 08:46:46 jtlin60 last message repeated 2 times
Sep 19 08:46:46 jtlin60 kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Sep 19 08:46:46 jtlin60 kernel: input: AT Set 2 keyboard on isa0060/serio0
Sep 19 08:46:46 jtlin60 kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Sep 19 08:46:46 jtlin60 kernel: NET: Registered protocol family 2
Sep 19 08:46:46 jtlin60 kernel: IP: routing cache hash table of 1024 buckets, 8Kbytes
Sep 19 08:46:46 jtlin60 kernel: TCP: Hash tables configured (established 16384 bind 16384)
Sep 19 08:46:46 jtlin60 kernel: Initializing IPsec netlink socket
Sep 19 08:46:46 jtlin60 kernel: NET: Registered protocol family 1
Sep 19 08:46:46 jtlin60 kernel: NET: Registered protocol family 17
Sep 19 08:46:46 jtlin60 kernel: NET: Registered protocol family 15
Sep 19 08:46:46 jtlin60 kernel: kjournald starting. Commit interval 5 seconds
Sep 19 08:46:46 jtlin60 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Sep 19 08:46:46 jtlin60 kernel: VFS: Mounted root (ext3 filesystem) readonly.
Sep 19 08:46:46 jtlin60 kernel: Freeing unused kernel memory: 112k freed
Sep 19 08:46:46 jtlin60 kernel: Adding 1028152k swap on /dev/hda2. Priority:-1 extents:1
Sep 19 08:46:46 jtlin60 pcmcia: Starting PCMCIA services:
Sep 19 08:46:46 jtlin60 kernel: EXT3 FS on hda1, internal journal
Sep 19 08:46:46 jtlin60 kernel: kjournald starting. Commit interval 5 seconds
Sep 19 08:46:46 jtlin60 kernel: EXT3 FS on hda3, internal journal
Sep 19 08:46:46 jtlin60 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Sep 19 08:46:46 jtlin60 kernel: kjournald starting. Commit interval 5 seconds
Sep 19 08:46:46 jtlin60 kernel: EXT3 FS on hda5, internal journal
Sep 19 08:46:46 jtlin60 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Sep 19 08:46:46 jtlin60 kernel: kjournald starting. Commit interval 5 seconds
Sep 19 08:46:46 jtlin60 kernel: EXT3 FS on hda6, internal journal
Sep 19 08:46:46 jtlin60 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Sep 19 08:46:46 jtlin60 kernel: updfstab: numerical sysctl 1 23 is obsolete.
Sep 19 08:46:47 jtlin60 kernel: kudzu: numerical sysctl 1 23 is obsolete.
Sep 19 08:46:47 jtlin60 kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
Sep 19 08:46:47 jtlin60 kernel: parport0: irq 7 detected
Sep 19 08:46:47 jtlin60 kernel: Linux Kernel Card Services 3.1.22
Sep 19 08:46:47 jtlin60 kernel: options: [pci] [cardbus] [pm]
Sep 19 08:46:47 jtlin60 kernel: PCI: Found IRQ 11 for device 0000:00:0b.0
Sep 19 08:46:47 jtlin60 kernel: Yenta: CardBus bridge found at 0000:00:0b.0 [1179:0001]
Sep 19 08:46:47 jtlin60 kernel: Yenta: ISA IRQ list 06b0, PCI irq11
Sep 19 08:46:47 jtlin60 kernel: Socket status: 30000020
Sep 19 08:46:47 jtlin60 kernel: PCI: Found IRQ 11 for device 0000:00:0b.1
Sep 19 08:46:47 jtlin60 kernel: Yenta: CardBus bridge found at 0000:00:0b.1 [1179:0001]
Sep 19 08:46:47 jtlin60 kernel: Yenta: ISA IRQ list 06b0, PCI irq11
Sep 19 08:46:47 jtlin60 kernel: Socket status: 30000007
Sep 19 08:46:48 jtlin60 pcmcia: cardmgr[564]: watching 2 sockets
Sep 19 08:46:48 jtlin60 cardmgr[564]: watching 2 sockets
Sep 19 08:46:48 jtlin60 kernel: cs: IO port probe 0x0c00-0x0cff: clean.
Sep 19 08:46:48 jtlin60 kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x2f8-0x2ff 0x3c0-0x3df 0x3f8-0x3ff 0x4d0-0x4d7
Sep 19 08:46:48 jtlin60 kernel: cs: IO port probe 0x0a00-0x0aff: clean.
Sep 19 08:46:48 jtlin60 cardmgr[565]: starting, version is 3.2.5
Sep 19 08:46:48 jtlin60 pcmcia: done.
Sep 19 08:46:48 jtlin60 rc: Starting pcmcia: succeeded
Sep 19 08:46:49 jtlin60 mount: mount: fs type devpts not supported by kernel
Sep 19 08:46:49 jtlin60 mount: mount: you must specify the filesystem type
Sep 19 08:46:49 jtlin60 netfs: Mounting other filesystems: failed
Sep 19 08:46:49 jtlin60 apmd[626]: Version 3.0.2 (APM BIOS 1.2, Linux driver 1.16ac)
Sep 19 08:46:49 jtlin60 apmd: apmd startup succeeded
Sep 19 08:46:49 jtlin60 autofs: automount startup succeeded
Sep 19 08:46:50 jtlin60 apmd[626]: Battery: * * * (100% 2:28)
Sep 19 08:46:51 jtlin60 xinetd[694]: xinetd Version 2002.03.28 started with libwrap options compiled in.
Sep 19 08:46:51 jtlin60 xinetd[694]: Started working: 2 available services
Sep 19 08:46:53 jtlin60 xinetd: xinetd startup succeeded
Sep 19 08:46:55 jtlin60 gpm: gpm startup succeeded
Sep 19 08:46:55 jtlin60 crond: crond startup succeeded
Sep 19 08:46:57 jtlin60 xfs: listening on port 7100
Sep 19 08:46:57 jtlin60 xfs: xfs startup succeeded
Sep 19 08:46:57 jtlin60 anacron: anacron startup succeeded
Sep 19 08:46:57 jtlin60 atd: atd startup succeeded
Sep 19 08:46:57 jtlin60 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/cyrillic (unreadable)
Sep 19 08:46:57 jtlin60 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/CID (unreadable)
Sep 19 08:46:57 jtlin60 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/local (unreadable)
Sep 19 08:46:57 jtlin60 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/latin2/Type1 (unreadable)
Sep 19 08:46:58 jtlin60 wine: Registering binary handler for Windows applications
Sep 19 08:46:58 jtlin60 wine: /etc/rc3.d/S98wine: /proc/sys/fs/binfmt_misc/register: No such file or directory
Sep 19 08:46:58 jtlin60 wine: /etc/rc3.d/S98wine: /proc/sys/fs/binfmt_misc/register: No such file or directory
Sep 19 08:46:58 jtlin60 rc: Starting wine: succeeded
Sep 19 08:46:58 jtlin60 kernel: warning: process `update' used the obsolete bdflush system call
Sep 19 08:46:58 jtlin60 kernel: Fix your initscripts?
Sep 19 08:47:02 jtlin60 apmd[626]: Now using AC Power
Sep 19 08:47:02 jtlin60 login(pam_unix)[869]: session opened for user root by LOGIN(uid=0)
Sep 19 08:47:02 jtlin60 -- root[869]: ROOT LOGIN ON tty1
Sep 19 08:47:03 jtlin60 kernel: warning: process `update' used the obsolete bdflush system call
Sep 19 08:47:03 jtlin60 kernel: Fix your initscripts?
Sep 19 08:47:34 jtlin60 kernel: drivers/usb/core/usb.c: registered new driver usbfs
Sep 19 08:47:34 jtlin60 kernel: drivers/usb/core/usb.c: registered new driver hub
Sep 19 08:47:50 jtlin60 kernel: drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
Sep 19 08:47:50 jtlin60 kernel: PCI: Found IRQ 11 for device 0000:00:05.2
Sep 19 08:47:50 jtlin60 kernel: PCI: Sharing IRQ 11 with 0000:00:0c.0
Sep 19 08:47:50 jtlin60 kernel: uhci-hcd 0000:00:05.2: UHCI Host Controller
Sep 19 08:47:50 jtlin60 kernel: Call Trace:
Sep 19 08:47:50 jtlin60 kernel: [<c010a56b>] __report_bad_irq+0x2f/0x90
Sep 19 08:47:50 jtlin60 kernel: [<c010a573>] __report_bad_irq+0x37/0x90
Sep 19 08:47:50 jtlin60 kernel: [<c010a640>] note_interrupt+0x50/0x78
Sep 19 08:47:50 jtlin60 kernel: [<c010a7b2>] do_IRQ+0x92/0xf0
Sep 19 08:47:50 jtlin60 kernel: [<c01092f0>] common_interrupt+0x18/0x20
Sep 19 08:47:50 jtlin60 kernel: [<c011aec7>] do_softirq+0x47/0xac
Sep 19 08:47:50 jtlin60 kernel: [<c010a7fd>] do_IRQ+0xdd/0xf0
Sep 19 08:47:50 jtlin60 kernel: [<c01092f0>] common_interrupt+0x18/0x20
Sep 19 08:47:50 jtlin60 kernel: [<c019ba69>] pci_bus_write_config_word+0x2d/0x40
Sep 19 08:47:50 jtlin60 kernel: [<cc91096e>] uhci_reset+0x2e/0x40 [uhci_hcd]
Sep 19 08:47:50 jtlin60 kernel: [<cc8b4d67>] usb_hcd_pci_probe+0x2eb/0x440 [usbcore]
Sep 19 08:47:50 jtlin60 kernel: [<c019e929>] pci_device_probe_static+0x2d/0x44
Sep 19 08:47:50 jtlin60 kernel: [<c019e960>] __pci_device_probe+0x20/0x38
Sep 19 08:47:50 jtlin60 kernel: [<c019e996>] pci_device_probe+0x1e/0x38
Sep 19 08:47:50 jtlin60 kernel: [<c01b9562>] bus_match+0x32/0x58
Sep 19 08:47:50 jtlin60 kernel: [<c01b9658>] driver_attach+0x44/0x84
Sep 19 08:47:50 jtlin60 kernel: [<c01b9863>] bus_add_driver+0x63/0x7c
Sep 19 08:47:50 jtlin60 kernel: [<c01b9af2>] driver_register+0x36/0x38
Sep 19 08:47:50 jtlin60 kernel: [<c019eb19>] pci_register_driver+0x59/0x7c
Sep 19 08:47:50 jtlin60 kernel: [<cc8a00ae>] uhci_hcd_init+0xae/0x130 [uhci_hcd]
Sep 19 08:47:50 jtlin60 kernel: [<c0129d81>] sys_init_module+0xe1/0x1ac
Sep 19 08:47:50 jtlin60 kernel: [<c0109183>] syscall_call+0x7/0xb
Sep 19 08:47:50 jtlin60 kernel:
Sep 19 08:47:50 jtlin60 kernel: handlers:
Sep 19 08:47:50 jtlin60 kernel: [<cc89b740>] (yenta_interrupt+0x0/0x2c [yenta_socket])
Sep 19 08:47:50 jtlin60 kernel: [<cc89b740>] (yenta_interrupt+0x0/0x2c [yenta_socket])
Sep 19 08:47:50 jtlin60 kernel: Disabling IRQ #11
Sep 19 08:47:50 jtlin60 kernel: uhci-hcd 0000:00:05.2: irq 11, io base 0000ff80
Sep 19 08:47:50 jtlin60 kernel: uhci-hcd 0000:00:05.2: new USB bus registered, assigned bus number 1
Sep 19 08:47:50 jtlin60 kernel: drivers/usb/host/uhci-hcd.c: detected 2 ports
Sep 19 08:47:50 jtlin60 kernel: usb usb1: Product: UHCI Host Controller
Sep 19 08:47:50 jtlin60 kernel: usb usb1: Manufacturer: Linux 2.6.0-test5 uhci-hcd
Sep 19 08:47:50 jtlin60 kernel: usb usb1: SerialNumber: 0000:00:05.2
Sep 19 08:47:50 jtlin60 kernel: hub 1-0:0: USB hub found
Sep 19 08:47:50 jtlin60 kernel: hub 1-0:0: 2 ports detected
Sep 19 08:47:51 jtlin60 kernel: hub 1-0:0: debounce: port 2: delay 100ms stable 4 status 0x301
Sep 19 08:47:51 jtlin60 kernel: hub 1-0:0: new USB device on port 2, assigned address 2
Sep 19 08:47:56 jtlin60 kernel: usb 1-2: control timeout on ep0out
Sep 19 08:47:56 jtlin60 kernel: uhci-hcd 0000:00:05.2: Unlink after no-IRQ? Different ACPI or APIC settings may help.
Sep 19 08:50:22 jtlin60 login(pam_unix)[870]: session opened for user root by LOGIN(uid=0)
Sep 19 08:50:22 jtlin60 -- root[870]: ROOT LOGIN ON tty2
cat /proc/version
Linux version 2.6.0-test5 (root@jtlin60) (gcc version 2.95.3 20010315 (release)) #9 Fri Sep 19 00:16:44 EDT 2003
cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 361.392
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 692.22
cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : 0000:00:07.0
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1000-10ff : PCI CardBus #02
1000-107f : 0000:02:00.0
1400-14ff : PCI CardBus #02
1800-18ff : PCI CardBus #06
1c00-1cff : 0000:00:07.0
2000-20ff : PCI CardBus #06
fe00-fe3f : 0000:00:05.3
fe60-fe7f : 0000:00:05.3
fefc-feff : 0000:00:0c.0
ff00-ff3f : 0000:00:0c.0
ff60-ff7f : 0000:00:09.0
ff80-ff9f : 0000:00:05.2
ff80-ff9f : uhci-hcd
fff0-ffff : 0000:00:05.1
fff0-fff7 : ide0
fff8-ffff : ide1
cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000e8000-000ebfff : reserved
000f0000-000fffff : System ROM
00100000-0bfdffff : System RAM
00100000-002440af : Kernel code
002440b0-002f0f1f : Kernel data
0bfe0000-0bfeffff : ACPI Tables
0bff0000-0bffffff : reserved
10000000-10000fff : 0000:00:0b.0
10000000-10000fff : yenta_socket
10001000-10001fff : 0000:00:0b.1
10001000-10001fff : yenta_socket
100a0000-100b6dff : reserved
100b6e00-100b6fff : ACPI Non-volatile Storage
100b7000-100fffff : reserved
10400000-107fffff : PCI CardBus #02
10400000-1041ffff : 0000:02:00.0
10800000-10bfffff : PCI CardBus #02
10800000-1080007f : 0000:02:00.0
10800080-108000ff : 0000:02:00.0
10c00000-10ffffff : PCI CardBus #06
11000000-113fffff : PCI CardBus #06
e0000000-e7ffffff : 0000:00:00.0
efff8000-efffffff : 0000:00:0c.0
f0000000-f7ffffff : PCI Bus #01
f0000000-f7ffffff : 0000:01:00.0
ffefff00-ffefffff : 0000:00:07.0
fff80000-ffffffff : reserved
cat /proc/scsi/scsi
cat: /proc/scsi/scsi: No such file or directory
lspci -vvv
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Subsystem: Toshiba America Info Systems Toshiba Tecra 8100 Laptop System Chipset
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f0000000-f7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:05.0 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:05.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at fff0 [size=16]
00:05.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at ff80 [size=32]
00:05.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:07.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
Subsystem: Toshiba America Info Systems Internal V.90 Modem
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at ffefff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 02f8 [size=8]
Region 2: I/O ports at 1c00 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 IRDA controller: Toshiba America Info Systems FIR Port Type-DO
Subsystem: Toshiba America Info Systems FIR Port Type-DO
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ff60 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1+,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to Cardbus Bridge with ZV Support (rev 20)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=0
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0b.1 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to Cardbus Bridge with ZV Support (rev 20)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=0
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001800-000018ff
I/O window 1: 00002000-000020ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0c.0 Multimedia audio controller: Yamaha Corporation YMF-744B [DS-1S Audio Controller] (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at efff8000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at ff00 [size=64]
Region 2: I/O ports at fefc [size=4]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/MX-MV (rev 11) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1000ns min, 63750ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=128M]
Expansion ROM at 000c0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 1.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
02:00.0 Ethernet controller: 3Com Corporation 3CCFE575CT Cyclone CardBus (rev 10)
Subsystem: 3Com Corporation FE575C-3Com 10/100 LAN CardBus-Fast Ethernet
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000 [disabled] [size=128]
Region 1: Memory at 10800000 (32-bit, non-prefetchable) [disabled] [size=128]
Region 2: Memory at 10800080 (32-bit, non-prefetchable) [disabled] [size=128]
Expansion ROM at 10400000 [disabled] [size=128K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
[-- Attachment #2: Linux.dot.config --]
[-- Type: text/plain, Size: 22127 bytes --]
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_STANDALONE=y
CONFIG_BROKEN_ON_SMP=y
#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
CONFIG_M386=y
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_L1_CACHE_SHIFT=4
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_X86_PPRO_FENCE=y
CONFIG_X86_F00F_BUG=y
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_HPET_TIMER is not set
# CONFIG_HPET_EMULATE_RTC is not set
# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
# CONFIG_X86_UP_APIC is not set
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_NONFATAL is not set
CONFIG_TOSHIBA=m
CONFIG_I8K=m
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
# CONFIG_EDD is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
# CONFIG_SOFTWARE_SUSPEND is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
# CONFIG_ACPI_HT is not set
# CONFIG_ACPI is not set
#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
CONFIG_APM_RTC_IS_GMT=y
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
CONFIG_EISA=y
# CONFIG_EISA_VLB_PRIMING is not set
# CONFIG_EISA_PCI_EISA is not set
# CONFIG_EISA_VIRTUAL_ROOT is not set
# CONFIG_EISA_NAMES is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
CONFIG_PCMCIA=m
CONFIG_YENTA=m
CONFIG_CARDBUS=y
CONFIG_I82092=m
CONFIG_I82365=m
CONFIG_TCIC=m
CONFIG_PCMCIA_PROBE=y
#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=m
CONFIG_HOTPLUG_PCI_FAKE=m
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
#
# Generic Driver Options
#
CONFIG_FW_LOADER=m
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
CONFIG_ISAPNP=y
# CONFIG_PNPBIOS is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_LBD=y
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_TASKFILE_IO=y
#
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
CONFIG_BLK_DEV_CMD64X=y
# CONFIG_BLK_DEV_TRIFLEX is not set
CONFIG_BLK_DEV_CY82C693=y
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
CONFIG_BLK_DEV_HPT34X=y
CONFIG_BLK_DEV_HPT366=y
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
CONFIG_BLK_DEV_SVWKS=y
# CONFIG_BLK_DEV_SIIMAGE is not set
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_SLC90E66=y
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_DMA_NONPCI is not set
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=m
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_REPORT_LUNS=y
# CONFIG_SCSI_CONSTANTS is not set
CONFIG_SCSI_LOGGING=y
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
CONFIG_SCSI_DEBUG=m
#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=y
CONFIG_UNIX=y
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_NAT=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_TOS=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
CONFIG_INET_IPCOMP=y
# CONFIG_IPV6 is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_NETFILTER is not set
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_LLC is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
CONFIG_EL3=m
# CONFIG_3C515 is not set
CONFIG_VORTEX=m
# CONFIG_TYPHOON is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
# CONFIG_NET_PCI is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPPOE is not set
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices (depends on LLC=y)
#
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
# CONFIG_PCMCIA_3C589 is not set
# CONFIG_PCMCIA_3C574 is not set
# CONFIG_PCMCIA_FMVJ18X is not set
# CONFIG_PCMCIA_PCNET is not set
# CONFIG_PCMCIA_NMCLAN is not set
# CONFIG_PCMCIA_SMC91C92 is not set
# CONFIG_PCMCIA_XIRC2PS is not set
# CONFIG_PCMCIA_AXNET is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Ltmodem
#
# CONFIG_LT_MODEM is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
CONFIG_INPUT_EVBUG=m
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_PCIPS2=y
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_DIGI is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
# CONFIG_UNIX98_PTYS is not set
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# I2C Hardware Sensors Mainboard support
#
#
# I2C Hardware Sensors Chip support
#
# CONFIG_I2C_SENSOR is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_QIC02_TAPE is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
CONFIG_AGP_ALI=m
# CONFIG_AGP_ATI is not set
CONFIG_AGP_AMD=m
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=m
# CONFIG_AGP_NVIDIA is not set
CONFIG_AGP_SIS=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_VIA=m
# CONFIG_DRM is not set
#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
# CONFIG_REISERFS_FS is not set
CONFIG_JFS_FS=m
# CONFIG_JFS_POSIX_ACL is not set
CONFIG_JFS_DEBUG=y
# CONFIG_JFS_STATISTICS is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=m
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
# CONFIG_QFMT_V2 is not set
CONFIG_QUOTACTL=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
CONFIG_NFSD=m
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=m
CONFIG_EXPORTFS=m
CONFIG_SUNRPC=m
# CONFIG_SUNRPC_GSS is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_CIFS is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
CONFIG_OSF_PARTITION=y
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
# CONFIG_LDM_PARTITION is not set
# CONFIG_NEC98_PARTITION is not set
CONFIG_SGI_PARTITION=y
# CONFIG_ULTRIX_PARTITION is not set
CONFIG_SUN_PARTITION=y
# CONFIG_EFI_PARTITION is not set
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Graphics support
#
# CONFIG_FB is not set
CONFIG_VIDEO_SELECT=y
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_MDA_CONSOLE=m
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
CONFIG_USB=m
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_UHCI_HCD=m
#
# USB Device Class drivers
#
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DEBUG=y
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
CONFIG_USB_MOUSE=m
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_XPAD is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network adaptors
#
# CONFIG_USB_AX8817X_STANDALONE is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_GADGET is not set
#
# Bluetooth support
#
# CONFIG_BT is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_IOVIRT is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
CONFIG_FRAME_POINTER=y
#
# Security options
#
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_TEST is not set
#
# Library routines
#
# CONFIG_CRC32 is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_X86_BIOS_REBOOT=y
next reply other threads:[~2003-09-19 13:42 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-09-19 13:36 jtholmes [this message]
2003-09-19 13:52 ` irq 11: nobody cared! is back Zwane Mwaikambo
2003-09-19 18:07 ` Andrew Morton
2003-09-19 19:34 ` Zwane Mwaikambo
2003-09-19 19:08 ` Greg KH
2003-09-19 19:27 ` David Brownell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3F6B0671.1070603@jtholmes.com \
--to=jtholmes@jtholmes.com \
--cc=jtholmesjr@comcast.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.