From: Matthew Kanar <mkanarlists@kanar.net>
To: linux-kernel@vger.kernel.org
Subject: Re: SMP broken on Dell PowerEdge 4100/200 under 2.6.0-testxx?
Date: Mon, 08 Dec 2003 11:42:57 -0500 [thread overview]
Message-ID: <3FD4AA11.6010806@kanar.net> (raw)
In-Reply-To: <ZCIb-2Pv-11@gated-at.bofh.it>
Here is one of my SMP systems (Dell-Dual P3), although noirqbalance
doesn't seem to change things --
uname -nrvm:
k12.kanar.net 2.6.0-test11 #2 SMP Wed Dec 3 18:50:36 EST 2003 i686
_Without_ noirqbalance -
uptime:
10:31:51 up 4 days, 15:07, 10 users, load average: 0.00, 0.02, 0.00
/proc/interrupts:
CPU0 CPU1
0: 27505 400084866 IO-APIC-edge timer
1: 1438 1 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
8: 1 0 IO-APIC-edge rtc
12: 1837 161 IO-APIC-edge i8042
14: 661467 822411 IO-APIC-edge ide0
15: 1 0 IO-APIC-edge ide1
16: 104949011 10 IO-APIC-level eth0
NMI: 0 0
LOC: 400153184 400153183
ERR: 0
MIS: 10
_With_ noirqbalance -
uptime:
11:36:12 up 1:01, 4 users, load average: 0.00, 0.09, 0.28
/proc/interrupts:
CPU0 CPU1
0: 16726 3707690 IO-APIC-edge timer
1: 3 8 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
8: 0 1 IO-APIC-edge rtc
12: 14 36 IO-APIC-edge i8042
14: 28140 659 IO-APIC-edge ide0
15: 1 0 IO-APIC-edge ide1
16: 12775 12 IO-APIC-level eth0
NMI: 0 0
LOC: 3724639 3724638
ERR: 0
MIS: 0
CPU0 timer: value 16726 hasn't changed since boot an hour ago.
dmesg:
Linux version 2.6.0-test11 (root@k12.kanar.net) (gcc version 3.2.2
20030222 (Red Hat Linux 3.2.2-5)) #2 SMP Wed Dec 3 18:50:36 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff9e000 (usable)
BIOS-e820: 000000001ff9e000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 130974
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126878 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000fd720
ACPI: RSDT (v001 DELL WS 420 0x00000008 ASL 0x00000061) @ 0x000fd734
ACPI: FADT (v001 DELL WS 420 0x00000008 ASL 0x00000061) @ 0x000fd760
ACPI: MADT (v001 DELL WS 420 0x00000008 ASL 0x00000061) @ 0x000fd7d4
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x01] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] polarity[0x1] trigger[0x1] lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: WS 420 APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Building zonelist for node : 0
Kernel command line: ro root=/dev/hda2 noirqbalance
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 930.947 MHz processor.
Console: colour VGA+ 80x25
Memory: 514112k/523896k available (2409k kernel code, 9044k reserved,
579k data, 352k init, 0k highmem)
Calibrating delay loop... 1839.10 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 732.06 usecs.
task migration cache decay timeout: 1 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1859.58 BogoMIPS
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 06
Total of 2 processors activated (3698.68 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-13, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 44.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 000 00 1 0 0 0 0 0 0 00
0e 001 01 0 0 0 0 0 1 1 91
0f 001 01 0 0 0 0 0 1 1 99
10 001 01 1 1 0 1 0 1 1 A1
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 B1
13 001 01 1 1 0 1 0 1 1 B9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 930.0810 MHz.
..... host bus clock speed is 132.0972 MHz.
checking TSC synchronization across 2 CPUs: passed.
Starting migration thread for cpu 0
Bringing up 1
CPU 1 IS NOW UP!
Starting migration thread for cpu 1
CPUS done 8
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfc03e, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/2410] at 0000:00:1f.0
PCI->APIC IRQ transform: (B0,I31,P3) -> 19
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I4,P0) -> 16
PCI->APIC IRQ transform: (B2,I6,P0) -> 18
PCI->APIC IRQ transform: (B2,I11,P0) -> 19
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
VFS: Disk quotas dquot_6.5.1
SGI XFS for Linux with no debug enabled
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
pty: 2048 Unix98 ptys configured
Real Time Clock Driver v1.12
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH: IDE controller at PCI slot 0000:00:1f.1
ICH: chipset revision 2
ICH: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD1200JB-75CRA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: LITEON DVD-ROM LTD163, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 234375000 sectors (120000 MB)
native capacity is 234375120 sectors (120000 MB)
hda: 234375000 sectors (120000 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(66)
hda: hda1 hda2 hda3
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 352k freed
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
EXT3 FS on hda2, internal journal
Adding 1044216k swap on /dev/hda3. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kudzu: numerical sysctl 1 23 is obsolete.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(08)
parport0: assign_addrs: aa5500ff(08)
parport0: cpp_daisy: aa5500ff(08)
parport0: assign_addrs: aa5500ff(08)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:04.0: 3Com PCI 3c905C Tornado at 0xec80. Vers LK1.1.19
divert: allocating divert_blk for eth0
/proc/cpuinfo:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 930.947
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse
bogomips : 1839.10
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 930.947
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse
bogomips : 1859.58
next parent reply other threads:[~2003-12-08 16:46 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <ZAwx-88m-3@gated-at.bofh.it>
[not found] ` <ZAGd-8ma-5@gated-at.bofh.it>
[not found] ` <ZAQ7-6X-13@gated-at.bofh.it>
[not found] ` <ZAZB-pS-11@gated-at.bofh.it>
[not found] ` <ZCoI-2oz-9@gated-at.bofh.it>
[not found] ` <ZCyh-2Bv-1@gated-at.bofh.it>
[not found] ` <ZCI5-2Pv-3@gated-at.bofh.it>
[not found] ` <ZCIb-2Pv-11@gated-at.bofh.it>
2003-12-08 16:42 ` Matthew Kanar [this message]
2003-12-08 17:21 ` SMP broken on Dell PowerEdge 4100/200 under 2.6.0-testxx? William Lee Irwin III
2003-12-08 17:38 ` Zwane Mwaikambo
[not found] <10wU2-1mR-11@gated-at.bofh.it>
[not found] ` <10wU2-1mR-13@gated-at.bofh.it>
[not found] ` <10wU2-1mR-15@gated-at.bofh.it>
[not found] ` <10wU3-1mR-17@gated-at.bofh.it>
[not found] ` <10wU3-1mR-19@gated-at.bofh.it>
[not found] ` <10wU3-1mR-21@gated-at.bofh.it>
[not found] ` <10wU3-1mR-23@gated-at.bofh.it>
[not found] ` <10wU3-1mR-25@gated-at.bofh.it>
[not found] ` <10wU2-1mR-9@gated-at.bofh.it>
[not found] ` <10xGk-38t-15@gated-at.bofh.it>
2003-12-08 19:24 ` Matthew Kanar
[not found] <fa.jiqirm0.13gv2u@ifi.uio.no>
[not found] ` <fa.f9f2gij.1kua0f@ifi.uio.no>
2003-12-06 17:38 ` William Park
2003-12-06 2:32 Colin Coe
2003-12-06 2:42 ` William Lee Irwin III
2003-12-06 2:48 ` William Lee Irwin III
2003-12-06 2:48 ` Nick Piggin
2003-12-06 3:07 ` William Lee Irwin III
2003-12-06 4:28 ` Stian Jordet
2003-12-06 4:37 ` William Lee Irwin III
2003-12-06 4:48 ` Stian Jordet
2003-12-06 4:54 ` William Lee Irwin III
2003-12-06 4:57 ` Stian Jordet
2003-12-06 5:09 ` William Lee Irwin III
2003-12-06 5:14 ` Stian Jordet
2003-12-06 5:40 ` William Lee Irwin III
2003-12-08 15:57 ` bill davidsen
2003-12-08 16:47 ` William Lee Irwin III
2003-12-06 7:11 ` Colin Coe
2003-12-08 15:45 ` bill davidsen
2003-12-08 17:36 ` Zwane Mwaikambo
2003-12-06 14:07 ` Adam Kropelin
2003-12-06 7:02 ` Colin Coe
2003-12-06 10:58 ` William Lee Irwin III
2003-12-06 20:08 ` Ethan Weinstein
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3FD4AA11.6010806@kanar.net \
--to=mkanarlists@kanar.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.