From: Roland Lezuo <roland.lezuo@chello.at>
To: linux-kernel@vger.kernel.org
Subject: usb-storage, sd_mod problem, with debugging infos ;)
Date: Wed, 23 Jun 2004 22:41:35 +0200 [thread overview]
Message-ID: <40D9EAFF.8070403@chello.at> (raw)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello,
I feel a bit ignored about this topic, but well I'll simply retry. Since
2.6.4 my usb stick does not work with linux any more. When searching the
internet for a solution I just find people with similar problems but no
solutions...
This happens when I plug in my stick (Traxdata EZ drive)
P.S.: please CC me personally, i'll try any patches...
usb 1-4: new high speed USB device using address 2
usb-storage: USB Mass Storage device detected
usb-storage: altsetting is 0, id_index is 92
usb-storage: -- associate_dev
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: Endpoints: In: 0xd315ef54 Out: 0xd315ef68 Int: 0x00000000
(Period 0)
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
~ Vendor: Generic Model: Rev:
~ Type: Direct-Access ANSI SCSI revision: 02
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
USB Mass Storage device found at 2
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xa L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xb L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 04 00
usb-storage: Bulk Command S 0x43425355 T 0xc L 4 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 4 bytes
usb-storage: Status code 0; transferred 4/4
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 08 00 04 00
usb-storage: Bulk Command S 0x43425355 T 0xd L 4 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 4 bytes
HERE: 1 minute delay
usb-storage: command_abort called
usb-storage: usb_stor_stop_transport called
usb-storage: -- cancelling URB
usb-storage: Status code -104; transferred 0/4
usb-storage: -- transfer cancelled
usb-storage: Bulk data transfer result 0x4
usb-storage: -- command was aborted
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset failed: -32
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -32; transferred 0/13
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = -71
usb-storage: Bulk status result = 4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset failed: -71
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: device_reset called
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset failed: -71
usb-storage: bus_reset called
usb-storage: usb_reset_device returns -19
scsi: Device offlined - not ready after error recovery: host 0 channel 0
id 0 lun 0
sda: asking for cache data failed
sda: assuming drive cache: write through
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: usb_stor_exit() called
usb-storage: -- calling usb_deregister()
usbcore: deregistering driver usb-storage
usb-storage: storage_disconnect() called
usb-storage: usb_stor_stop_transport called
usb-storage: -- dissociate_dev
devfs_remove: scsi/host0/bus0/target0/lun0/generic not found, cannot remove
~ [<c0104e2e>] dump_stack+0x1e/0x20
~ [<c01df1f6>] devfs_remove+0xa6/0xb0
~ [<c02af2bf>] sg_remove+0xdf/0x260
~ [<c026c693>] class_device_del+0xc3/0xd0
~ [<c026c6b4>] class_device_unregister+0x14/0x20
~ [<c02a91a9>] scsi_remove_device+0x39/0xb0
~ [<c02a84f4>] scsi_forget_host+0x44/0x90
~ [<c02a13bc>] scsi_remove_host+0x2c/0x60
~ [<e09b0605>] storage_disconnect+0x45/0x51 [usb_storage]
~ [<e09ba0f6>] usb_unbind_interface+0x76/0x80 [usbcore]
~ [<c026b8c6>] device_release_driver+0x66/0x70
~ [<c026b8f2>] driver_detach+0x22/0x40
~ [<c026bb95>] bus_remove_driver+0x55/0x90
~ [<c026bffa>] driver_unregister+0x1a/0x42
~ [<e09ba1d3>] usb_deregister+0x33/0x40 [usbcore]
~ [<e09b0caa>] usb_stor_exit+0x2a/0x2c [usb_storage]
~ [<c012e62f>] sys_delete_module+0x14f/0x1c0
~ [<c010402f>] syscall_call+0x7/0xb
usb-storage: -- sending exit command to thread
usb-storage: *** thread awakened.
usb-storage: -- exit command received
usb-storage: -- usb_stor_release_resources finished
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.3 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org
iD8DBQFA2er/5qlVDPzJ7R4RAh33AJ9IUkP1n3POJK+PPQ9QB37YQDsIxgCgpm9S
6qb9SrQ3EmzOm0p4zkBdjoI=
=pqZm
-----END PGP SIGNATURE-----
next reply other threads:[~2004-06-23 20:43 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-06-23 20:41 Roland Lezuo [this message]
2004-06-23 21:06 ` usb-storage, sd_mod problem, with debugging infos ;) Matthew Dharm
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=40D9EAFF.8070403@chello.at \
--to=roland.lezuo@chello.at \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.