From: administrator tootai <admin@tootai.net>
To: bluez-users@lists.sourceforge.net
Subject: Re: [Bluez-users] Re: Connection issue with headset
Date: Fri, 04 Feb 2005 13:25:11 +0100 [thread overview]
Message-ID: <420369A7.1070203@tootai.net> (raw)
In-Reply-To: <ctv8ou$aa1$2@sea.gmane.org>
Sebastian Roth a =E9crit :
> Hi Daniel,
Hi Sebastian
>> 2.6.10 (debian) + patch swsusp2 & bluez-utils 2.10-5 (debian sid)
>
> As I said before please give it a try and update your kernel with the
> current patch from bluez.org and install the latest versions of
> utils and lib (source is also available at bluez.org)
nomade:/etc# uname -r
2.6.10-mh3-custom.3
nomade:/usr/lib# ls /usr/lib/libblu*
/usr/lib/libbluetooth.a /usr/lib/libbluetooth.so =20
/usr/lib/libbluetooth.so.1.0.15
/usr/lib/libbluetooth.la /usr/lib/libbluetooth.so.1
Utils also upgraded.
>
> Haven't seen any output of the SCO module in your dmesg. Make sure
> you have enabled CONFIG_BT_SCO and CONFIG_BT_HCIUSB_SCO in your kernel
> config and loaded the module 'sco'!
nomade:/etc# lsmod
Module Size Used by
sco 15108 0
snd_bt_sco 13728 0
snd_hwdep 9540 1 snd_bt_sco
ndiswrapper 114264 0
rfcomm 41116 0
l2cap 27140 3 rfcomm
nomade:/usr/src/linux# hciconfig -a
hci0: Type: USB
BD Address: 00:0C:41:E2:4C:B0 ACL MTU: 192:8 SCO MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:1851 acl:49 sco:0 events:89 errors:0
TX bytes:1287 acl:47 sco:0 commands:29 errors:0
Features: 0xff 0xff 0x0f 0x00 0x00 0x00 0x00 0x00
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'BlueZ (0)'
Class: 0x3e0100
Service Classes: Networking, Rendering, Capturing
Device Class: Computer, Uncategorized
HCI Ver: 1.1 (0x1) HCI Rev: 0x20d LMP Ver: 1.1 (0x1) LMP Subver:=20
0x20d
Manufacturer: Cambridge Silicon Radio (10)
>> #sdptool search --bdaddr 00:0b:2e:06:01:2e 0x1108
>
> [...]
>
>> Channel: 6
>
> [...]
>
>> nomade:/etc/waproamd/keys# btsco 00:0b:2e:06:01:2e
>> Device is 1:0
>> Voice setting: 0x0060
>> RFCOMM channel 6 connected
>> speaker volume: 10 mic volume: 10
>
> Channel should be ok. Now where are the new message from? Does it
> work now?
speaker volume message: I always get it the first time I run btsco=20
*after* having loaded snd-bt-sco. The hcidump is below. Still this 2=20
ERROR unexpected syntax.
nomade:/usr/src/linux# hcidump -X
HCIDump - HCI packet analyzer ver 1.12
device: hci0 snap_len: 1028 filter: 0xffffffff
< HCI Command: Create Connection (0x01|0x0005) plen 13
0000: 2e 01 06 2e 0b 00 18 cc 02 00 00 00 01 .............
> HCI Event: Command Status (0x0f) plen 4
0000: 00 01 05 04 ....
> HCI Event: Link Key Request (0x17) plen 6
0000: 2e 01 06 2e 0b 00 ......
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
0000: 2e 01 06 2e 0b 00 98 0f 70 e7 ad ee 4b 1a 93 1c ........p...K...
0010: ba 18 77 0c 19 00 ..w...
> HCI Event: Command Complete (0x0e) plen 10
0000: 01 0b 04 00 2e 01 06 2e 0b 00 ..........
> HCI Event: Connect Complete (0x03) plen 11
0000: 00 29 00 2e 01 06 2e 0b 00 01 00 .).........
< ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 1 scid 0x0040
< HCI Command: Write Link Policy Settings (0x02|0x000d) plen 4
0000: 29 00 0f 00 )...
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> HCI Event: Max Slots Change (0x1b) plen 3
0000: 29 00 05 )..
> HCI Event: Command Complete (0x0e) plen 6
0000: 01 0d 08 00 29 00 ....).
> ACL data: handle 0x0029 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
< ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 0
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 0
> ACL data: handle 0x0029 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 4
MTU 48
< ACL data: handle 0x0029 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 0
< ACL data: handle 0x0029 flags 0x02 dlen 24
L2CAP(d): cid 0x0040 len 20 [psm 1]
SDP SSA Req: tid 0x0 len 0xf
pat uuid-16 0x1108 (Headset)
max 0xffff
aid(s) 0x0000 - 0xffff
cont 00
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 27
> ACL data: handle 0x0029 flags 0x01 dlen 24
L2CAP(d): cid 0x0040 len 47 [psm 1]
SDP SSA Rsp: tid 0x0 len 0x2a
cnt 0x26
srv rec #0
aid 0x0000 (SrvRecHndl)
uint 0x20000
aid 0x0001 (SrvClassIDList)
< uuid-16 0x1108 (Headset) uuid-16 0x1203 (Audio) >
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) > <
uuid-16 0x0003 (RFCOMM) null null > >
cont
< ACL data: handle 0x0029 flags 0x02 dlen 25
L2CAP(d): cid 0x0040 len 21 [psm 1]
SDP SSA Req: tid 0x1 len 0x10
pat uuid-16 0x1108 (Headset)
max 0xffff
aid(s) 0x0000 - 0xffff
cont 01 01
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 27
> ACL data: handle 0x0029 flags 0x01 dlen 22
L2CAP(d): cid 0x0040 len 45 [psm 1]
SDP SSA Rsp: tid 0x1 len 0x28
cnt 0x24
ERROR: Unexpected syntax
0000: 06 09 00 05 35 03 19 10 02 09 00 06 35 09 09 65 =20
....5.......5..e
0010: 6e 09 00 6a 09 01 00 09 01 00 25 07 48 65 61 64 =20
n..j......%.Head
0020: 73 65 74 01 02 set..
cont 06 09 00 05 35 03 19 10 02 09 00 06 35 09 09 65 6E 09 00=20
6A 09 01 00 09 01 00 25 0748 65 61 64 73 65 74 01 02
< ACL data: handle 0x0029 flags 0x02 dlen 25
L2CAP(d): cid 0x0040 len 21 [psm 1]
SDP SSA Req: tid 0x2 len 0x10
pat uuid-16 0x1108 (Headset)
max 0xffff
aid(s) 0x0000 - 0xffff
cont 01 02
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 17
L2CAP(d): cid 0x0040 len 13 [psm 1]
SDP SSA Rsp: tid 0x2 len 0x8
cnt 0x5
ERROR: Unexpected syntax
0000: 03 02 28 01 00 ..(..
cont 03 02 28 01 00
< ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0040 scid 0x0040
< HCI Command: Read Voice Setting (0x03|0x0025) plen 0
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
> HCI Event: Command Complete (0x0e) plen 6
0000: 01 25 0c 00 60 00 .%..`.
< ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 3 scid 0x0040
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
< ACL data: handle 0x0029 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 4
MTU 1024
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 18
L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 4
MTU 1024
> ACL data: handle 0x0029 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 4
MTU 317
< ACL data: handle 0x0029 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 0
< ACL data: handle 0x0029 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): SABM: cr 1 dlci 0 pf 1 ilen 0 fcs 0x1c
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): UA: cr 1 dlci 0 pf 1 ilen 0 fcs 0xd7
< ACL data: handle 0x0029 flags 0x02 dlen 18
L2CAP(d): cid 0x0040 len 14 [psm 3]
RFCOMM(s): PN CMD: cr 1 dlci 0 pf 0 ilen 10 fcs 0x70 mcc_len 8
dlci 12 frame_type 0 credit_flow 15 pri 7 ack_timer 0
frame_size 312 max_retrans 0 credits 7
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 18
L2CAP(d): cid 0x0040 len 14 [psm 3]
RFCOMM(s): PN RSP: cr 0 dlci 0 pf 0 ilen 10 fcs 0xaa mcc_len 8
dlci 12 frame_type 0 credit_flow 14 pri 1 ack_timer 0
frame_size 312 max_retrans 0 credits 7
< ACL data: handle 0x0029 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): SABM: cr 1 dlci 12 pf 1 ilen 0 fcs 0x43
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): UA: cr 1 dlci 12 pf 1 ilen 0 fcs 0x88
< ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(d): cid 0x0040 len 8 [psm 3]
RFCOMM(s): MSC CMD: cr 1 dlci 0 pf 0 ilen 4 fcs 0x70 mcc_len 2
dlci 12 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 1 b2 1 b3 0 len 0
> ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(d): cid 0x0040 len 8 [psm 3]
RFCOMM(s): MSC CMD: cr 0 dlci 0 pf 0 ilen 4 fcs 0xaa mcc_len 2
dlci 12 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 1 b2 1 b3 0 len 0
< ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(d): cid 0x0040 len 8 [psm 3]
RFCOMM(s): MSC RSP: cr 1 dlci 0 pf 0 ilen 4 fcs 0x70 mcc_len 2
dlci 12 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 1 b2 1 b3 0 len 0
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
> ACL data: handle 0x0029 flags 0x02 dlen 12
L2CAP(d): cid 0x0040 len 8 [psm 3]
RFCOMM(s): MSC RSP: cr 0 dlci 0 pf 0 ilen 4 fcs 0xaa mcc_len 2
dlci 12 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 1 b2 1 b3 0 len 0
< ACL data: handle 0x0029 flags 0x02 dlen 9
L2CAP(d): cid 0x0040 len 5 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 12 pf 1 ilen 0 fcs 0x53 credits 33
> HCI Event: Number of Completed Packets (0x13) plen 5
0000: 01 29 00 01 00 .)...
Thanks for your help
--=20
Daniel
-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
Tool for open source databases. Create drag-&-drop reports. Save time
by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
next prev parent reply other threads:[~2005-02-04 12:25 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-01-28 9:32 [Bluez-users] Connection issue with headset administrator tootai
2005-01-28 15:53 ` [Bluez-users] " Sebastian Roth
2005-01-29 16:39 ` daniel huhardeaux
2005-01-29 16:43 ` administrator tootai
2005-01-29 17:29 ` Stefan Bellon
2005-01-30 3:13 ` Brad Midgley
2005-01-30 19:01 ` administrator tootai
2005-01-31 14:57 ` administrator tootai
2005-01-31 14:58 ` Marcel Holtmann
2005-01-31 15:30 ` administrator tootai
2005-01-31 15:55 ` Marcel Holtmann
2005-01-31 18:20 ` administrator tootai
2005-02-01 16:37 ` Sebastian Roth
2005-02-02 13:20 ` administrator tootai
2005-02-02 16:21 ` Sebastian Roth
2005-02-02 16:55 ` administrator tootai
2005-02-03 14:13 ` Sebastian Roth
2005-02-03 21:39 ` administrator tootai
2005-02-04 7:38 ` Sebastian Roth
2005-02-04 12:25 ` administrator tootai [this message]
2005-02-03 17:06 ` administrator tootai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=420369A7.1070203@tootai.net \
--to=admin@tootai.net \
--cc=bluez-users@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.