From: "Robert W. Fuller" <orangemagicbus@sbcglobal.net>
To: linux-kernel@vger.kernel.org
Subject: 2.6.11 USB broken on VIA computer (not just ACPI)
Date: Tue, 15 Mar 2005 22:19:29 -0500 [thread overview]
Message-ID: <4237A5C1.5030709@sbcglobal.net> (raw)
This isn't limited to the ACPI case. My BIOS is old enough that ACPI is
not supported because the kernel can't find RSDP. I found that the USB
works if I boot with "noapic." This is probably sub-optimal on an SMP
machine. If don't boot with "noapic" I get the following errors:
Mar 15 21:30:17 falcon USB Universal Host Controller Interface driver v2.2
Mar 15 21:30:17 falcon uhci_hcd 0000:00:07.2: VIA Technologies, Inc.
VT82xxxxx UHCI USB 1.1 Controller
Mar 15 21:30:17 falcon uhci_hcd 0000:00:07.2: irq 19, io base 0xa400
Mar 15 21:30:17 falcon uhci_hcd 0000:00:07.2: new USB bus registered,
assigned bus number 1
Mar 15 21:30:17 falcon hub 1-0:1.0: USB hub found
Mar 15 21:30:17 falcon hub 1-0:1.0: 2 ports detected
Mar 15 21:30:17 falcon usb 1-2: new low speed USB device using uhci_hcd
and address 2
Mar 15 21:30:18 falcon uhci_hcd 0000:00:07.2: Unlink after no-IRQ?
Controller is probably using the wrong IRQ.
Mar 15 21:30:18 falcon usb 1-2: khubd timed out on ep0in
Mar 15 21:30:24 falcon usb 1-2: khubd timed out on ep0out
Mar 15 21:30:29 falcon usb 1-2: khubd timed out on ep0out
Mar 15 21:30:29 falcon usb 1-2: device not accepting address 2, error -110
Here's my lspci:
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo
PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
Expansion ROM at 00009000 [disabled] [size=4K]
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile
South] (rev 23)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
(prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 11) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power
Management (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:0f.0 Unknown mass storage controller: Promise Technology, Inc.
20269 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra133TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a800
Region 1: I/O ports at ac00 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at b400 [size=4]
Region 4: I/O ports at b800 [size=16]
Region 5: Memory at e3000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1
(rev 08)
Subsystem: Creative Labs CT4760 SBLive!
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at bc00
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 Input device controller: Creative Labs SB Live! MIDI/Game
Port (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at c000
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:12.0 Multimedia video controller: Brooktree Corporation Bt878
Video Capture (rev 11)
Subsystem: Avermedia Technologies Inc AVerTV WDM Video Capture
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e3004000 (32-bit, prefetchable)
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:12.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)
Subsystem: Avermedia Technologies Inc AVerTV WDM Audio Capture
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e3005000 (32-bit, prefetchable)
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:14.0 Ethernet controller: Lite-On Communications Inc LNE100TX
(rev 20)
Subsystem: Lite-On Communications Inc LNE100TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c400
Region 1: Memory at e3006000 (32-bit, non-prefetchable) [size=256]
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R100
QD [Radeon 7200] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon 7000/Radeon
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable)
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e1000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next reply other threads:[~2005-03-16 3:32 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-03-16 3:19 Robert W. Fuller [this message]
2005-03-16 4:39 ` 2.6.11 USB broken on VIA computer (not just ACPI) Andrew Morton
2005-03-16 5:28 ` Robert W. Fuller
2005-03-16 5:31 ` Andrew Morton
2005-03-16 5:37 ` Robert W. Fuller
2005-03-16 5:54 ` Andrew Morton
2005-03-16 6:58 ` Robert W. Fuller
2005-03-16 17:19 ` Greg KH
2005-03-16 17:50 ` Robert W. Fuller
2005-03-16 17:56 ` Greg KH
2005-03-16 10:00 ` Documentation/i386/IO-APIC.txt (Re: 2.6.11 USB broken on VIA computer (not just ACPI)) Xavier Bestel
2005-03-16 10:08 ` Xavier Bestel
2005-03-16 17:17 ` 2.6.11 USB broken on VIA computer (not just ACPI) Greg KH
-- strict thread matches above, loose matches on Subject: below --
2005-05-12 8:47 paul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4237A5C1.5030709@sbcglobal.net \
--to=orangemagicbus@sbcglobal.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.