From: "Frieder Bürzele" <linux-stuff@arcor.de>
To: linux-kernel@vger.kernel.org
Subject: oops in ohci_hcd with kernel 2.6.12 - 2.6.14-rc3-git2
Date: Sun, 02 Oct 2005 17:37:06 +0200 [thread overview]
Message-ID: <433FFEA2.3050103@arcor.de> (raw)
[-- Attachment #1: Type: text/plain, Size: 267 bytes --]
Hi,
since kernel version ~2.6.12 I occasionally get oopes with the ohci_hcd
modul during boot.
I need to reboot 5 times or more until the machine works.
mainboard is a Asus A7N266-C with nforce chipset
thx
Please CC me thx
attached is dmesg-2.6.14-rc3-git2-oops
[-- Attachment #2: dmesg-2.6.14-rc3-git2-oops --]
[-- Type: text/plain, Size: 12442 bytes --]
i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKC] -> GSI 18 (level, high) -> IRQ 16
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 5000K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE: IDE controller at PCI slot 0000:00:09.0
NFORCE: chipset revision 195
NFORCE: not 100% native mode: will probe irqs later
NFORCE: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE: 0000:00:09.0 (rev c3) UDMA100 controller
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: MAXTOR 4K080H4, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
hdd: ASUS CRW-4012A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2000KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 >
libata version 1.12 loaded.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
DECnet: Routing cache hash table of 1024 buckets, 8Kbytes
NET: Registered protocol family 12
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PCI1 UAR1 UAR2 PS2K USB0 USB1
ACPI: (supports S0 S1 S3 S4 S5)
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard on isa0060/serio0
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: replayed 11 transactions in 0 seconds
ReiserFS: hda2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 172k freed
Adding 497972k swap on /dev/hda6. Priority:-1 extents:1 across:497972k
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:01:02.0[A] -> Link [LNKC] -> GSI 18 (level, high) -> IRQ 16
eth0: RealTek RTL8139 at 0xc800, 00:e0:18:74:94:30, IRQ 16
eth0: Identified 8139 chip type 'RTL-8100'
fuse init (API version 7.2)
Realtime LSM initialized (group 18, mlock=1)
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
usbcore: registered new driver usbfs
usbcore: registered new driver hub
cdrom: open failed.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce chipset
agpgart: AGP aperture is 64M @ 0xf8000000
PCI: Enabling device 0000:00:06.0 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKK] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKK] -> GSI 22 (level, high) -> IRQ 17
PCI: Setting latency timer of device 0000:00:06.0 to 64
AC'97 1 analog subsections not ready
intel8x0_measure_ac97_clock: measured 63220 usecs
intel8x0: clocking to 48000
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKU] -> GSI 21 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: USB HC TakeOver from BIOS/SMM
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 18, io mem 0xee800000
ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: fminterval a7782edf
ohci_hcd 0000:00:02.0: hcca frame #0003
ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=1 NPS NDP=3(3)
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.14-rc3-git2 ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKU] -> GSI 21 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:03.0 to 64
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 18, io mem 0xee000000
ohci_hcd 0000:00:03.0: resetting from state 'reset', control = 0x600
Unable to handle kernel NULL pointer dereference at virtual address 00000024
printing eip:
d0b24b7f
*pde = 00000000
Oops: 0002 [#1]
PREEMPT
Modules linked in: ohci_hcd snd_pcm_oss snd_mixer_oss snd_seq_oss snd_virmidi snd_seq_virmidi snd_rawmidi snd_seq_midi_event snd_seq snd_seq_device snd_intel8x0 snd_ac97_codec snd_ac97_bus snd_pcm snd_timer snd soundcore snd_page_alloc nvidia_agp agpgart usbcore realtime commoncap fuse 8139too ide_cd
CPU: 0
EIP: 0060:[<d0b24b7f>] Not tainted VLI
EFLAGS: 00010203 (2.6.14-rc3-git2)
EIP is at usb_lock_device+0xf/0x20 [usbcore]
eax: d0b44004 ebx: cf4d7800 ecx: c1276750 edx: 00000000
esi: 00000206 edi: cf4d7b08 ebp: c1276740 esp: cff03f38
ds: 007b es: 007b ss: 0068
Process events/0 (pid: 3, threadinfo=cff02000 task=c1268030)
Stack: d0c067db cf4d7b04 c012ab8e 00000000 00000000 c1268a50 cff02000 c1276758
c1276748 c1276750 cff02000 cf4d7800 d0c067d0 cff02000 ffffffff ffffffff
00000001 00000000 c01178d0 00010000 00000000 c1268a50 00000000 cff9ff68
Call Trace:
[<d0c067db>] ohci_rh_resume+0xb/0x20 [ohci_hcd]
[<c012ab8e>] worker_thread+0x1ae/0x280
[<d0c067d0>] ohci_rh_resume+0x0/0x20 [ohci_hcd]
[<c01178d0>] default_wake_function+0x0/0x10
[<c01178d0>] default_wake_function+0x0/0x10
[<c012a9e0>] worker_thread+0x0/0x280
[<c012ec35>] kthread+0x95/0xd0
[<c012eba0>] kthread+0x0/0xd0
[<c0101375>] kernel_thread_helper+0x5/0x10
Code: 83 c0 14 e9 b4 0e 76 ef 8d 74 26 00 f3 c3 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 89 c2 b8 04 40 b4 d0 ff 00 0f 88 57 05 00 00 <ff> 4a 24 0f 88 5c 05 00 00 c3 8d b4 26 00 00 00 00 53 89 c1 bb
<7>ohci_hcd 0000:00:03.0: OHCI controller state
ohci_hcd 0000:00:03.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:03.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:03.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:03.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:03.0: fminterval a7782edf
ohci_hcd 0000:00:03.0: hcca frame #0004
ohci_hcd 0000:00:03.0: roothub.a 01000203 POTPGT=1 NPS NDP=3(3)
ohci_hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:03.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:03.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:03.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:03.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:03.0: created debug files
ohci_hcd 0000:00:03.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.14-rc3-git2 ohci_hcd
usb usb2: SerialNumber: 0000:00:03.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-2: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: Microsoft IntelliMouse® Explorer
usb 1-2: Manufacturer: Microsoft
usb 1-2: hotplug
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: hotplug
hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0008
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: new full speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: ep0 maxpacket = 16
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=5
usb 2-3: Product: TARGA 6in1 reader
usb 2-3: Manufacturer: SCM Microsystems Inc.
usb 2-3: SerialNumber: 00000000094C
usb 2-3: hotplug
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: hotplug
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0004
hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0008
next reply other threads:[~2005-10-02 15:36 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-10-02 15:37 Frieder Bürzele [this message]
2005-10-02 20:52 ` oops in ohci_hcd with kernel 2.6.12 - 2.6.14-rc3-git2 Greg KH
-- strict thread matches above, loose matches on Subject: below --
2005-10-02 21:30 Frieder Bürzele
2005-10-02 22:55 ` Frieder Bürzele
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=433FFEA2.3050103@arcor.de \
--to=linux-stuff@arcor.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.