From: Giacomo Catenazzi <cate@cateee.net>
To: linux-kernel@vger.kernel.org
Subject: ppc kernel bugs in2.6.15-rc5: kobject_register failed for usbcore (-17)
Date: Wed, 07 Dec 2005 18:42:00 +0100 [thread overview]
Message-ID: <43971EE8.1080204@cateee.net> (raw)
I have some call trace in 2.6.15-rc5 (I don't know if
it happens also on old kernel, new machine, my first non x86 kernel)
Uniform CD-ROM driver Revision: 3.20
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Apple UniNorth 2 chipset
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
kobject_register failed for ohci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c016eb50] bus_add_driver+0x80/0x180
[c016f978] driver_register+0x48/0x60
[c010cda4] __pci_register_driver+0x84/0xe0
[e1026044] ohci_hcd_pci_init+0x44/0xd0 [ohci_hcd]
[c0046b38] sys_init_module+0x158/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40]
MMIO=[f5000000-f50007ff] Max Packet=[2048]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
kobject_register failed for ohci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c016eb50] bus_add_driver+0x80/0x180
[c016f978] driver_register+0x48/0x60
[c010cda4] __pci_register_driver+0x84/0xe0
[e1026044] ohci_hcd_pci_init+0x44/0xd0 [ohci_hcd]
[c0046b38] sys_init_module+0x158/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001124fffed13718]
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Adding 1269520k swap on /dev/hda3. Priority:-1 extents:1 across:1269520k
EXT3 FS on hda4, internal journal
SCSI subsystem initialized
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
kobject_register failed for ohci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c016eb50] bus_add_driver+0x80/0x180
[c016f978] driver_register+0x48/0x60
[c010cda4] __pci_register_driver+0x84/0xe0
[e20dd044] ohci_hcd_pci_init+0x44/0xd0 [ohci_hcd]
[c0046b38] sys_init_module+0x158/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
kobject_register failed for ehci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
[The hdc error was reported also on the original debian kernel, I should
still check]
ciao
cate
reply other threads:[~2005-12-07 17:43 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43971EE8.1080204@cateee.net \
--to=cate@cateee.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.