From: "Miroslav Zajíc" <Zajsoft@Zajsoft.NET>
To: bugme-daemon@bugzilla.kernel.org
Cc: Zajsoft2@Zajsoft.NET, James.Bottomley@steeleye.com,
linux-scsi@vger.kernel.org
Subject: Re: [Bug 5808] aic7xxx - half speed/frequency
Date: Thu, 05 Jan 2006 15:36:29 +0100 [thread overview]
Message-ID: <43BD2EED.3060404@Zajsoft.NET> (raw)
In-Reply-To: <200601041758.k04Hw8Sf015281@fire-2.osdl.org>
Hi,
in 2.6.15 is same problem :o(
The please try say me some sysfs settings.
Thanks,
Zajsoft
bugme-daemon@bugzilla.kernel.org napsal(a):
>http://bugzilla.kernel.org/show_bug.cgi?id=5808
>
>
>
>
>
>------- Additional Comments From anonymous@kernel-bugs.osdl.org 2006-01-04 09:47 -------
>Reply-To: James.Bottomley@SteelEye.com
>
>Could you keep the cc: list when replying, otherwise we lose the
>tracking information in the bug database and on the list.
>
>Could you try this again with 2.6.15, and then I can try giving you some
>sysfs settings to prod to see if the driver can be forced up to 50ns.
>
>Thanks,
>
>James
>
>
>On Tue, 2006-01-03 at 01:30 +0100, Miroslav Zajíc wrote:
>
>
>>from dmesg - 2.6.12.6:
>>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>> <Adaptec aic7880 Ultra SCSI adapter>
>> aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
>>
>> Vendor: SEAGATE Model: ST34573LC Rev: 5702
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:0:0: Tagged Queuing enabled. Depth 32
>> target0:0:0: Beginning Domain Validation
>>WIDTH IS 1
>>(scsi0:A:0): 6.600MB/s transfers (16bit)
>> target0:0:0: Domain Validation skipping write tests
>>(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>> target0:0:0: Ending Domain Validation
>> Vendor: SEAGATE Model: ST19171W Rev: 2219
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:1:0: Tagged Queuing enabled. Depth 32
>> target0:0:1: Beginning Domain Validation
>>WIDTH IS 1
>>(scsi0:A:1): 6.600MB/s transfers (16bit)
>> target0:0:1: Domain Validation skipping write tests
>>(scsi0:A:1): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>> target0:0:1: Ending Domain Validation
>> Vendor: SEAGATE Model: ST19171W Rev: 2219
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:2:0: Tagged Queuing enabled. Depth 32
>> target0:0:2: Beginning Domain Validation
>>WIDTH IS 1
>>(scsi0:A:2): 6.600MB/s transfers (16bit)
>> target0:0:2: Domain Validation skipping write tests
>>(scsi0:A:2): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>> target0:0:2: Ending Domain Validation
>> Vendor: SEAGATE Model: ST19171W Rev: 2224
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:3:0: Tagged Queuing enabled. Depth 32
>> target0:0:3: Beginning Domain Validation
>>WIDTH IS 1
>>(scsi0:A:3): 6.600MB/s transfers (16bit)
>> target0:0:3: Domain Validation skipping write tests
>>(scsi0:A:3): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>> target0:0:3: Ending Domain Validation
>> Vendor: SEAGATE Model: ST39173LC Rev: 5702
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:4:0: Tagged Queuing enabled. Depth 32
>> target0:0:4: Beginning Domain Validation
>>WIDTH IS 1
>>(scsi0:A:4): 6.600MB/s transfers (16bit)
>> target0:0:4: Domain Validation skipping write tests
>>(scsi0:A:4): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>> target0:0:4: Ending Domain Validation
>> Vendor: SEAGATE Model: ST19171W Rev: 2224
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:5:0: Tagged Queuing enabled. Depth 32
>> target0:0:5: Beginning Domain Validation
>>WIDTH IS 1
>>(scsi0:A:5): 6.600MB/s transfers (16bit)
>> target0:0:5: Domain Validation skipping write tests
>>(scsi0:A:5): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>> target0:0:5: Ending Domain Validation
>>(scsi0:A:6:0): refuses WIDE negotiation. Using 8bit transfers
>>(scsi0:A:6:0): refuses synchronous negotiation. Using asynchronous transfers
>> Vendor: DELL Model: 6UW BACKPLANE Rev: 7
>> Type: Processor ANSI SCSI revision: 02
>> target0:0:6: Beginning Domain Validation
>> target0:0:6: Ending Domain Validation
>>scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>> <Adaptec aic7860 Ultra SCSI adapter>
>> aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
>>
>> Vendor: NEC Model: CD-ROM DRIVE:464 Rev: 1.05
>> Type: CD-ROM ANSI SCSI revision: 02
>> target1:0:5: Beginning Domain Validation
>> target1:0:5: Domain Validation skipping write tests
>>(scsi1:A:5): 20.000MB/s transfers (20.000MHz, offset 15)
>> target1:0:5: Ending Domain Validation
>>
>>/sys/class/spi_transport/target<...>/min_period - 2.6.12.6:
>>
>>target0:0:0
>>target0:0:1
>>target0:0:2
>>target0:0:3
>>target0:0:4
>>target0:0:5
>>target0:0:6
>>target1:0:5
>>for all - 12.5
>>
>>
>>from dmesg - 2.6.13:
>>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>> <Adaptec aic7880 Ultra SCSI adapter>
>> aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
>>
>> target0:0:0: asynchronous.
>> Vendor: SEAGATE Model: ST34573LC Rev: 5702
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:0:0: Tagged Queuing enabled. Depth 32
>> target0:0:0: Beginning Domain Validation
>> target0:0:0: wide asynchronous.
>> target0:0:0: Domain Validation skipping write tests
>> target0:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
>> target0:0:0: Ending Domain Validation
>> target0:0:1: asynchronous.
>> Vendor: SEAGATE Model: ST19171W Rev: 2219
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:1:0: Tagged Queuing enabled. Depth 32
>> target0:0:1: Beginning Domain Validation
>> target0:0:1: wide asynchronous.
>> target0:0:1: Domain Validation skipping write tests
>> target0:0:1: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
>> target0:0:1: Ending Domain Validation
>> target0:0:2: asynchronous.
>> Vendor: SEAGATE Model: ST19171W Rev: 2219
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:2:0: Tagged Queuing enabled. Depth 32
>> target0:0:2: Beginning Domain Validation
>> target0:0:2: wide asynchronous.
>> target0:0:2: Domain Validation skipping write tests
>> target0:0:2: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
>> target0:0:2: Ending Domain Validation
>> target0:0:3: asynchronous.
>> Vendor: SEAGATE Model: ST19171W Rev: 2224
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:3:0: Tagged Queuing enabled. Depth 32
>> target0:0:3: Beginning Domain Validation
>> target0:0:3: wide asynchronous.
>> target0:0:3: Domain Validation skipping write tests
>> target0:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
>> target0:0:3: Ending Domain Validation
>> target0:0:4: asynchronous.
>> Vendor: SEAGATE Model: ST39173LC Rev: 5702
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:4:0: Tagged Queuing enabled. Depth 32
>> target0:0:4: Beginning Domain Validation
>> target0:0:4: wide asynchronous.
>> target0:0:4: Domain Validation skipping write tests
>> target0:0:4: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
>> target0:0:4: Ending Domain Validation
>> target0:0:5: asynchronous.
>> Vendor: SEAGATE Model: ST19171W Rev: 2224
>> Type: Direct-Access ANSI SCSI revision: 02
>>scsi0:A:5:0: Tagged Queuing enabled. Depth 32
>> target0:0:5: Beginning Domain Validation
>> target0:0:5: wide asynchronous.
>> target0:0:5: Domain Validation skipping write tests
>> target0:0:5: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
>> target0:0:5: Ending Domain Validation
>>(scsi0:A:6:0): refuses WIDE negotiation. Using 8bit transfers
>> target0:0:6: asynchronous.
>>(scsi0:A:6:0): refuses synchronous negotiation. Using asynchronous transfers
>> Vendor: DELL Model: 6UW BACKPLANE Rev: 7
>> Type: Processor ANSI SCSI revision: 02
>> target0:0:6: Beginning Domain Validation
>> target0:0:6: Ending Domain Validation
>>scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>> <Adaptec aic7860 Ultra SCSI adapter>
>> aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
>>
>> target1:0:5: asynchronous.
>> Vendor: NEC Model: CD-ROM DRIVE:464 Rev: 1.05
>> Type: CD-ROM ANSI SCSI revision: 02
>> target1:0:5: Beginning Domain Validation
>> target1:0:5: Domain Validation skipping write tests
>> target1:0:5: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
>> target1:0:5: Ending Domain Validation
>>
>>
>>/sys/class/spi_transport/target<...>/min_period - 2.6.3:
>>target0:0:0
>>target0:0:1
>>target0:0:2
>>target0:0:3
>>target0:0:4
>>target0:0:5
>>target0:0:6
>>target1:0:5
>>for all - 100
>>
>>
>>Zajsoft
>>
>>
>>
>>James Bottomley napsal(a):
>>
>>
>>
>>>On Sun, 2006-01-01 at 16:41 -0800, bugme-daemon@bugzilla.kernel.org
>>>wrote:
>>>
>>>
>>>
>>>
>>>>Most recent kernel where this bug did not occur: 2.6.12.6
>>>>Distribution: Debian 3.1r1 - Sarge
>>>>
>>>>
>>>>
>>>>
>>>Do you have the dmesg showing the domain validation commands for these, please?
>>>
>>>And also could you tell me what's in
>>>
>>>/sys/spi_transport/target<...>/min_period
>>>
>>>Thanks,
>>>
>>>James
>>>
>>>
>>>
>>>
>>>
>>>
>>>>Hardware Environment: Dell PowerEdge 4200/300
>>>>
>>>>Software Environment:
>>>>ver_linux:
>>>>Linux GW 2.6.13 #1 SMP Sun Jan 1 21:13:01 CET 2006 i686 GNU/Linux
>>>>
>>>>Gnu C 3.3.5
>>>>Gnu make 3.80
>>>>binutils 2.15
>>>>util-linux 2.12p
>>>>mount 2.12p
>>>>module-init-tools 3.2-pre1
>>>>e2fsprogs 1.37
>>>>jfsutils 1.1.7
>>>>xfsprogs 2.6.20
>>>>Linux C Library 2.3.2
>>>>Dynamic linker (ldd) 2.3.2
>>>>Procps 3.2.1
>>>>Net-tools 1.60
>>>>Console-tools 0.2.3
>>>>Sh-utils 5.2.1
>>>>Modules Loaded
>>>>
>>>>
>>>>proc/cpuinfo:
>>>>processor : 0
>>>>vendor_id : GenuineIntel
>>>>cpu family : 6
>>>>model : 3
>>>>model name : Pentium II (Klamath)
>>>>stepping : 4
>>>>cpu MHz : 299.170
>>>>cache size : 512 KB
>>>>fdiv_bug : no
>>>>hlt_bug : no
>>>>f00f_bug : no
>>>>coma_bug : no
>>>>fpu : yes
>>>>fpu_exception : yes
>>>>cpuid level : 2
>>>>wp : yes
>>>>flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
>>>>cmov mmx
>>>>bogomips : 599.32
>>>>
>>>>processor : 1
>>>>vendor_id : GenuineIntel
>>>>cpu family : 6
>>>>model : 3
>>>>model name : Pentium II (Klamath)
>>>>stepping : 3
>>>>cpu MHz : 299.170
>>>>cache size : 512 KB
>>>>fdiv_bug : no
>>>>hlt_bug : no
>>>>f00f_bug : no
>>>>coma_bug : no
>>>>fpu : yes
>>>>fpu_exception : yes
>>>>cpuid level : 2
>>>>wp : yes
>>>>flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
>>>>cmov mmx
>>>>bogomips : 598.36
>>>>
>>>>
>>>>/proc/modules:
>>>>
>>>>
>>>>/proc/ioports:
>>>>0000-001f : dma1
>>>>0020-0021 : pic1
>>>>0040-0043 : timer0
>>>>0050-0053 : timer1
>>>>0060-006f : keyboard
>>>>0070-0077 : rtc
>>>>0080-008f : dma page reg
>>>>00a0-00a1 : pic2
>>>>00c0-00df : dma2
>>>>00f0-00ff : fpu
>>>>0330-0333 : i2c-pca-isa
>>>>03c0-03df : vga+
>>>>0400-0407 : pnp 00:0f
>>>>040a-040c : pnp 00:0f
>>>>0410-043f : pnp 00:0f
>>>>0461-0462 : pnp 00:0f
>>>>0464-0465 : pnp 00:0f
>>>>0481-048b : pnp 00:0f
>>>>04c6-04c6 : pnp 00:0f
>>>>0c80-0c83 : Dell System PowerEdge 4200
>>>>0cf8-0cff : PCI conf1
>>>>e000-efff : PCI Bus #01
>>>> e000-e0ff : 0000:01:0d.0
>>>> e000-e0ff : 8139too
>>>> e400-e4ff : 0000:01:0b.0
>>>> e800-e8ff : 0000:01:0a.0
>>>>f4a0-f4bf : 0000:00:13.0
>>>> f4a0-f4bf : ne2k-pci
>>>>f800-f8ff : 0000:00:14.0
>>>>
>>>>
>>>>/proc/iomem:
>>>>00000000-0009fbff : System RAM
>>>>0009fc00-0009ffff : reserved
>>>>000a0000-000bffff : Video RAM area
>>>>000c0000-000c7fff : Video ROM
>>>>000c8000-000cc7ff : Adapter ROM
>>>>000f0000-000fffff : System ROM
>>>>00100000-0fffffff : System RAM
>>>> 00100000-0049816c : Kernel code
>>>> 0049816d-005b31c7 : Kernel data
>>>>10000000-100fffff : PCI Bus #01
>>>> 10000000-1000ffff : 0000:01:0a.0
>>>>10100000-1010ffff : 0000:00:14.0
>>>>10110000-10113fff : 0000:00:13.0
>>>>fc000000-fcffffff : 0000:00:14.0
>>>>fde00000-fdffffff : PCI Bus #01
>>>> fdefe000-fdefefff : 0000:01:0a.0
>>>> fdefe000-fdefefff : aic7xxx
>>>> fdffe000-fdffefff : 0000:01:0b.0
>>>> fdffe000-fdffefff : aic7xxx
>>>> fdfff800-fdfff8ff : 0000:01:0d.0
>>>> fdfff800-fdfff8ff : 8139too
>>>>fec00000-fec00fff : reserved
>>>>fee00000-fee00fff : reserved
>>>>fff80000-ffffffff : reserved
>>>>
>>>>
>>>>lspci -vvv:
>>>>0000:00:00.0 Host bridge: Intel Corp. 440FX - 82441FX PMC [Natoma] (rev 02)
>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>Stepping- SERR+ FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort+ >SERR- <PERR-
>>>> Latency: 32
>>>>
>>>>0000:00:0d.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02)
>>>>(prog-if 00 [Normal decode])
>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>Stepping- SERR+ FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Latency: 255, Cache Line Size: 0x08 (32 bytes)
>>>> Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>>>> I/O behind bridge: 0000e000-0000efff
>>>> Memory behind bridge: fde00000-fdffffff
>>>> Prefetchable memory behind bridge: 0000000010000000-0000000010000000
>>>> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>>>>
>>>>0000:00:0f.0 Non-VGA unclassified device: Intel Corp. 82375EB/SB PCI to EISA
>>>>Bridge (rev 15)
>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
>>>>Stepping- SERR- FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Latency: 248
>>>>
>>>>0000:00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
>>>> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>Stepping- SERR- FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Interrupt: pin A routed to IRQ 10
>>>> Region 0: I/O ports at f4a0 [size=32]
>>>> Expansion ROM at 10110000 [disabled] [size=16K]
>>>>
>>>>0000:00:14.0 VGA compatible controller: ATI Technologies Inc 264VT [Mach64 VT]
>>>>(rev 40) (prog-if 00 [VGA])
>>>> Subsystem: ATI Technologies Inc Mach64VT Reference
>>>> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop+ ParErr-
>>>>Stepping+ SERR- FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
>>>> Region 1: I/O ports at f800 [size=256]
>>>> Expansion ROM at 10100000 [disabled] [size=64K]
>>>>
>>>>0000:01:0a.0 SCSI storage controller: Adaptec AIC-7880U
>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
>>>>Stepping- SERR+ FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Latency: 64 (2000ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
>>>> Interrupt: pin A routed to IRQ 15
>>>> Region 0: I/O ports at e800 [disabled] [size=256]
>>>> Region 1: Memory at fdefe000 (32-bit, non-prefetchable) [size=4K]
>>>> Expansion ROM at 10000000 [disabled] [size=64K]
>>>>
>>>>0000:01:0b.0 SCSI storage controller: Adaptec AIC-7860 (rev 01)
>>>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
>>>>Stepping- SERR+ FastB2B-
>>>> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Latency: 64 (1000ns min, 1000ns max), Cache Line Size: 0x08 (32 bytes)
>>>> Interrupt: pin A routed to IRQ 15
>>>> Region 0: I/O ports at e400 [disabled] [size=256]
>>>> Region 1: Memory at fdffe000 (32-bit, non-prefetchable) [size=4K]
>>>>
>>>>0000:01:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-
>>>>8139/8139C/8139C+ (rev 10)
>>>> Subsystem: Realtek Semiconductor Co., Ltd. RT8139
>>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>>>>Stepping- SERR+ FastB2B-
>>>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>>>><TAbort- <MAbort- >SERR- <PERR-
>>>> Latency: 64 (8000ns min, 16000ns max)
>>>> Interrupt: pin A routed to IRQ 9
>>>> Region 0: I/O ports at e000 [size=256]
>>>> Region 1: Memory at fdfff800 (32-bit, non-prefetchable) [size=256]
>>>> Capabilities: [50] Power Management version 2
>>>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-
>>>>,D1+,D2+,D3hot+,D3cold-)
>>>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>>>>
>>>>
>>>>/proc/scsi/scsi:
>>>>Attached devices:
>>>>Host: scsi0 Channel: 00 Id: 00 Lun: 00
>>>> Vendor: SEAGATE Model: ST34573LC Rev: 5702
>>>> Type: Direct-Access ANSI SCSI revision: 02
>>>>Host: scsi0 Channel: 00 Id: 01 Lun: 00
>>>> Vendor: SEAGATE Model: ST19171W Rev: 2219
>>>> Type: Direct-Access ANSI SCSI revision: 02
>>>>Host: scsi0 Channel: 00 Id: 02 Lun: 00
>>>> Vendor: SEAGATE Model: ST19171W Rev: 2219
>>>> Type: Direct-Access ANSI SCSI revision: 02
>>>>Host: scsi0 Channel: 00 Id: 03 Lun: 00
>>>> Vendor: SEAGATE Model: ST19171W Rev: 2224
>>>> Type: Direct-Access ANSI SCSI revision: 02
>>>>Host: scsi0 Channel: 00 Id: 04 Lun: 00
>>>> Vendor: SEAGATE Model: ST39173LC Rev: 5702
>>>> Type: Direct-Access ANSI SCSI revision: 02
>>>>Host: scsi0 Channel: 00 Id: 05 Lun: 00
>>>> Vendor: SEAGATE Model: ST19171W Rev: 2224
>>>> Type: Direct-Access ANSI SCSI revision: 02
>>>>Host: scsi0 Channel: 00 Id: 06 Lun: 00
>>>> Vendor: DELL Model: 6UW BACKPLANE Rev: 7
>>>> Type: Processor ANSI SCSI revision: 02
>>>>Host: scsi1 Channel: 00 Id: 05 Lun: 00
>>>> Vendor: NEC Model: CD-ROM DRIVE:464 Rev: 1.05
>>>> Type: CD-ROM
>>>>
>>>>
>>>>/proc/scsi/aic7xxx/0:
>>>>Adaptec AIC7xxx driver version: 6.2.36
>>>>Adaptec aic7880 Ultra SCSI adapter
>>>>aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
>>>>Allocated SCBs: 36, SG List Length: 128
>>>>
>>>>Serial EEPROM:
>>>>0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338
>>>>0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338
>>>>0x18b6 0x005e 0x2807 0x0010 0xff00 0xffff 0xffff 0xffff
>>>>0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x00ff 0x74a1
>>>>
>>>>Target 0 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Curr: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Channel A Target 0 Lun 0 Settings
>>>> Commands Queued 1283
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 1 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Curr: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Channel A Target 1 Lun 0 Settings
>>>> Commands Queued 46
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 2 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Curr: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Channel A Target 2 Lun 0 Settings
>>>> Commands Queued 37
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 3 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Curr: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Channel A Target 3 Lun 0 Settings
>>>> Commands Queued 36
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 4 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Curr: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Channel A Target 4 Lun 0 Settings
>>>> Commands Queued 36
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 5 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Curr: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
>>>> Channel A Target 5 Lun 0 Settings
>>>> Commands Queued 45
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 6 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 3.300MB/s transfers
>>>> Curr: 3.300MB/s transfers
>>>> Channel A Target 6 Lun 0 Settings
>>>> Commands Queued 6
>>>> Commands Active 0
>>>> Command Openings 1
>>>> Max Tagged Openings 0
>>>> Device Queue Frozen Count 0
>>>>Target 7 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 8 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 9 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 10 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 11 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 12 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 13 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 14 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 15 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>
>>>>
>>>>/proc/scsi/aic7xxx/1:
>>>>Adaptec AIC7xxx driver version: 6.2.36
>>>>Adaptec aic7860 Ultra SCSI adapter
>>>>aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
>>>>Allocated SCBs: 4, SG List Length: 128
>>>>
>>>>Serial EEPROM:
>>>>0x0318 0x0318 0x0318 0x0318 0x0318 0x0318 0x0318 0x0318
>>>>0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338
>>>>0x18b5 0x005e 0x2807 0x5008 0xff00 0xffff 0xffff 0xffff
>>>>0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x00ff 0xc398
>>>>
>>>>Target 0 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 1 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 2 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 3 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 4 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 5 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>> Goal: 10.000MB/s transfers (10.000MHz, offset 15)
>>>> Curr: 10.000MB/s transfers (10.000MHz, offset 15)
>>>> Channel A Target 5 Lun 0 Settings
>>>> Commands Queued 16
>>>> Commands Active 0
>>>> Command Openings 1
>>>> Max Tagged Openings 0
>>>> Device Queue Frozen Count 0
>>>>Target 6 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 7 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>
>>>>
>>>>/proc/scsi/aic7xxx/0 - from kernel 2.6.12.6:
>>>>
>>>>Adaptec AIC7xxx driver version: 6.2.36
>>>>Adaptec aic7880 Ultra SCSI adapter
>>>>aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
>>>>Allocated SCBs: 8, SG List Length: 128
>>>>
>>>>Serial EEPROM:
>>>>0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338
>>>>0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338
>>>>0x18b6 0x005e 0x2807 0x0010 0xff00 0xffff 0xffff 0xffff
>>>>0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x00ff 0x74a1
>>>>
>>>>Target 0 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Curr: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Channel A Target 0 Lun 0 Settings
>>>> Commands Queued 1459
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 1 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Curr: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Channel A Target 1 Lun 0 Settings
>>>> Commands Queued 48
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 2 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Curr: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Channel A Target 2 Lun 0 Settings
>>>> Commands Queued 38
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 3 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Curr: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Channel A Target 3 Lun 0 Settings
>>>> Commands Queued 37
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 4 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Curr: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Channel A Target 4 Lun 0 Settings
>>>> Commands Queued 37
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 5 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Curr: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
>>>> Channel A Target 5 Lun 0 Settings
>>>> Commands Queued 47
>>>> Commands Active 0
>>>> Command Openings 32
>>>> Max Tagged Openings 32
>>>> Device Queue Frozen Count 0
>>>>Target 6 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>> Goal: 3.300MB/s transfers
>>>> Curr: 3.300MB/s transfers
>>>> Channel A Target 6 Lun 0 Settings
>>>> Commands Queued 6
>>>> Commands Active 0
>>>> Command Openings 1
>>>> Max Tagged Openings 0
>>>> Device Queue Frozen Count 0
>>>>Target 7 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 8 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 9 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 10 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 11 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 12 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 13 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 14 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>Target 15 Negotiation Settings
>>>> User: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
>>>>
>>>>
>>>>/proc/scsi/aic7xxx/1 - from kernel 2.6.12.6:
>>>>Adaptec AIC7xxx driver version: 6.2.36
>>>>Adaptec aic7860 Ultra SCSI adapter
>>>>aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
>>>>Allocated SCBs: 4, SG List Length: 128
>>>>
>>>>Serial EEPROM:
>>>>0x0318 0x0318 0x0318 0x0318 0x0318 0x0318 0x0318 0x0318
>>>>0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338 0x0338
>>>>0x18b5 0x005e 0x2807 0x5008 0xff00 0xffff 0xffff 0xffff
>>>>0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x00ff 0xc398
>>>>
>>>>Target 0 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 1 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 2 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 3 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 4 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 5 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>> Goal: 20.000MB/s transfers (20.000MHz, offset 15)
>>>> Curr: 20.000MB/s transfers (20.000MHz, offset 15)
>>>> Channel A Target 5 Lun 0 Settings
>>>> Commands Queued 16
>>>> Commands Active 0
>>>> Command Openings 1
>>>> Max Tagged Openings 0
>>>> Device Queue Frozen Count 0
>>>>Target 6 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>Target 7 Negotiation Settings
>>>> User: 20.000MB/s transfers (20.000MHz, offset 127)
>>>>
>>>>Problem Description:
>>>>If use kernel 2.6.13 or newer, all SCSI discs/cdrom work only on half
>>>>speed/frequency.
>>>>
>>>>Steps to reproduce:
>>>>Only boot... cat /proc/scsi/aic7xxx/0
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>>
>
>
>
>------- You are receiving this mail because: -------
>You reported the bug, or are watching the reporter.
>
>
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next parent reply other threads:[~2006-01-05 14:37 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <200601041758.k04Hw8Sf015281@fire-2.osdl.org>
2006-01-05 14:36 ` Miroslav Zajíc [this message]
2006-01-06 16:43 ` [Bug 5808] aic7xxx - half speed/frequency James Bottomley
2006-01-06 19:45 ` Miroslav Zajíc
2006-01-06 21:46 ` James Bottomley
[not found] <200601020041.k020fes2021946@fire-2.osdl.org>
2006-01-02 16:28 ` James Bottomley
[not found] ` <43B9C5A8.5090800@Zajsoft.NET>
2006-01-04 17:57 ` James Bottomley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43BD2EED.3060404@Zajsoft.NET \
--to=zajsoft@zajsoft.net \
--cc=James.Bottomley@steeleye.com \
--cc=Zajsoft2@Zajsoft.NET \
--cc=bugme-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.