From: Christopher Smith <csmith@nighthawkrad.net>
To: Brad Campbell <brad@wasp.net.au>
Cc: linux-raid@vger.kernel.org
Subject: Re: Problems with multiple Promise SATA150 TX4 cards
Date: Wed, 25 Jan 2006 11:15:04 +1100 [thread overview]
Message-ID: <43D6C308.5040603@nighthawkrad.net> (raw)
In-Reply-To: <43D62B4F.1080505@nighthawkrad.net>
Christopher Smith wrote:
> Brad Campbell wrote:
>> Can you send an lspci -vv please? I did have some strange problems
>> with the BIOS setting up weird timing modes on some of the cards. This
>> did not present a reliability problem for me, just performance however.
>
> I attached lspci output to my original post. I have also included it on
> the end of this one (with a slight difference regarding which slots the
> cards were in, but that makes no difference to the problem).
Oops, forgot to attach lspci output - that's what you get for posting
just before bed :).
[root@terminus ~]# lspci -vv
00:00.0 Host bridge: Intel Corporation E7501 Memory Controller Hub (rev 01)
Subsystem: Intel Corporation E7501 Memory Controller Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [40] Vendor Specific Information
00:02.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface B
PCI-to-PCI Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fc400000-fc6fffff
Prefetchable memory behind bridge: ff300000-ff5fffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:03.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface C
PCI-to-PCI Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=04, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc700000-fc9fffff
Prefetchable memory behind bridge: ff600000-ff8fffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1) (rev
02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 209
Region 4: I/O ports at ec00 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #2) (rev
02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 217
Region 4: I/O ports at e880 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #3) (rev
02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 169
Region 4: I/O ports at e800 [size=32]
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 42) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: ff900000-ff9fffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801CA LPC Interface Controller
(rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801CA Ultra ATA Storage
Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 88000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0540 [size=32]
01:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc6ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=1 Dev=28 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=01, secondary=02, subordinate=02, sec-latency=48
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fc400000-fc4fffff
Prefetchable memory behind bridge:
00000000ff300000-00000000ff300000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=0
Status: Bus=1 Dev=29 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
01:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc6fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=1 Dev=30 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fc500000-fc5fffff
Prefetchable memory behind bridge:
00000000ff400000-00000000ff400000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=3
Status: Bus=1 Dev=31 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
02:02.0 Mass storage controller: Promise Technology, Inc. PDC20318
(SATA150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20318 (SATA150 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 4500ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at ac00 [size=64]
Region 1: I/O ports at a880 [size=16]
Region 2: I/O ports at a800 [size=128]
Region 3: Memory at fc4ff000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fc4c0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fc4f8000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:02.0 Ethernet controller: Intel Corporation 82544GC Gigabit Ethernet
Controller (LOM) (rev 02)
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 201
Region 0: Memory at fc5e0000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at fc5c0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at bc00 [size=32]
Expansion ROM at fc5a0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=3 Dev=2 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=2, DMOST=0, DMCRS=1, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
04:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc9ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=4 Dev=28 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
04:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=04, secondary=05, subordinate=05, sec-latency=64
Memory behind bridge: fc700000-fc7fffff
Prefetchable memory behind bridge:
00000000ff600000-00000000ff600000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=3
Status: Bus=4 Dev=29 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
04:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc9fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=4 Dev=30 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
04:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=04, secondary=06, subordinate=06, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc800000-fc8fffff
Prefetchable memory behind bridge:
00000000ff700000-00000000ff700000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=0
Status: Bus=4 Dev=31 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
06:03.0 Mass storage controller: Promise Technology, Inc. PDC20318
(SATA150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20318 (SATA150 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 90
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at cc00 [size=64]
Region 1: I/O ports at c880 [size=16]
Region 2: I/O ports at c800 [size=128]
Region 3: Memory at fc8ff000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fc8c0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fc8f8000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
07:02.0 Mass storage controller: Promise Technology, Inc. PDC20318
(SATA150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20318 (SATA150 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 90
Interrupt: pin A routed to IRQ 193
Region 0: I/O ports at dc00 [size=64]
Region 1: I/O ports at d480 [size=16]
Region 2: I/O ports at d400 [size=128]
Region 3: Memory at feafe000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at feaa0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at ff920000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
07:0c.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at ff900000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[root@terminus ~]#
next prev parent reply other threads:[~2006-01-25 0:15 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-24 2:01 Problems with multiple Promise SATA150 TX4 cards Christopher Smith
2006-01-24 6:39 ` Mark Hahn
2006-01-24 6:58 ` Christopher Smith
2006-01-24 9:11 ` Brad Campbell
2006-01-24 13:27 ` Christopher Smith
2006-01-25 0:15 ` Christopher Smith [this message]
2006-01-25 5:33 ` Mattias Wadenstein
2006-01-24 17:40 ` David Greaves
2006-01-25 10:04 ` Erik Slagter
2006-01-26 0:26 ` Christopher Smith
2006-01-26 11:35 ` Erik Slagter
2006-01-26 14:22 ` David Greaves
2006-01-26 14:44 ` Hans Kristian Rosbach
2006-01-27 6:00 ` Mitchell Laks
2006-01-27 13:21 ` berk walker
2006-03-22 17:26 ` Ian Oliver
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43D6C308.5040603@nighthawkrad.net \
--to=csmith@nighthawkrad.net \
--cc=brad@wasp.net.au \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.