From: Stefan <stefan-kernel@simg.de>
To: linux-kernel@vger.kernel.org
Subject: Crash when bunring CD/DVD
Date: Mon, 13 Mar 2006 23:55:31 +0100 [thread overview]
Message-ID: <4415F863.9040203@simg.de> (raw)
Hello,
When I try to burn CD's/DVD's my computer crashes.
It seems to be independently from the recording software and from the
drive. It occurs with cdrecord (cdrecord-clone version 2.01.01a01 from
debian) and growisofs (version 5.21 from debian), and with the drives
NEC ND-4550A and LG GMA-4020B.
The problem occurs at least with the kernels 2.6.14.7, 2.6.15.4 and
2.6.16-rc6 (The earlier verions I tested are very unstable. Mostly
it was not possible even to boot.)
Unfortunately I cant obtain any error messages, even with several debug
options turned on. Here is a screenshot :-) of crashed cdrecord, but
there is nothing unnormal to see:
http://www.simg.de/tmp10/cd-2.6.16-rc6.png
That is my .config:
http://www.simg.de/tmp10/2.6.16-rc6-config
My hardware is:
Mainboard: Tyan S2466 (AMD 760MPX Dual Athlon board, latest BIOS)
CPU's: 2 x Barton MP 2133 MHz
Memory: 2GB registred ECC
Drives: see below
PCI: see bolow
More Info is attached below. Please mail me, if you need more.
Best regards,
Stefan
----------------------------------------------------------------------------------
/proc/scsi:
Attached devices:
Host: scsi0 Channel: 01 Id: 00 Lun: 00
Vendor: MAXTOR Model: ATLAS15K2_73SCA Rev: JNZM
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 01 Id: 01 Lun: 00
Vendor: FUJITSU Model: MAN3367MP Rev: 0109
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: _NEC Model: DVD_RW ND-4550A Rev: 1.07
Type: CD-ROM ANSI SCSI revision: ffffffff
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: HL-DT-ST Model: DVDRAM GMA-4020B Rev: A109
Type: CD-ROM ANSI SCSI revision: ffffffff
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: STORAGE DEVICE Rev: 9317
Type: Direct-Access ANSI SCSI revision: 02
----------------------------------------------------------------------------------
ide/scsi boot messages:
Mar 13 20:33:39 ws2 kernel: ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
Mar 13 20:33:39 ws2 kernel: AMD7441: IDE controller at PCI slot 0000:00:07.1
Mar 13 20:33:39 ws2 kernel: AMD7441: chipset revision 4
Mar 13 20:33:39 ws2 kernel: AMD7441: not 100%% native mode: will probe
irqs later
Mar 13 20:33:39 ws2 kernel: AMD7441: 0000:00:07.1 (rev 04) UDMA100
controller
Mar 13 20:33:39 ws2 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS
settings: hda:DMA, hdb:DMA
Mar 13 20:33:39 ws2 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS
settings: hdc:DMA, hdd:DMA
Mar 13 20:33:39 ws2 kernel: hda: HDT722525DLAT80, ATA DISK drive
Mar 13 20:33:39 ws2 kernel: hdb: Pioneer DVD-ROM ATAPIModel DVD-106S
012, ATAPI CD/DVD-ROM drive
Mar 13 20:33:39 ws2 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Mar 13 20:33:39 ws2 kernel: hdc: _NEC DVD_RW ND-4550A, ATAPI CD/DVD-ROM
drive
Mar 13 20:33:39 ws2 kernel: hdd: HL-DT-ST DVDRAM GMA-4020B, ATAPI
CD/DVD-ROM drive
Mar 13 20:33:39 ws2 kernel: ide1 at 0x170-0x177,0x376 on irq 15
Mar 13 20:33:39 ws2 kernel: hda: max request size: 1024KiB
Mar 13 20:33:39 ws2 kernel: hda: 488397168 sectors (250059 MB) w/7674KiB
Cache, CHS=30401/255/63, UDMA(100)
Mar 13 20:33:39 ws2 kernel: hda: cache flushes supported
Mar 13 20:33:39 ws2 kernel: hda: hda1 hda2 hda3
Mar 13 20:33:39 ws2 kernel: hdb: ATAPI 40X DVD-ROM drive, 256kB Cache,
UDMA(66)
Mar 13 20:33:39 ws2 kernel: Uniform CD-ROM driver Revision: 3.20
Mar 13 20:33:39 ws2 kernel: ide-cd: passing drive hdc to ide-scsi emulation.
Mar 13 20:33:39 ws2 kernel: ide-cd: passing drive hdd to ide-scsi emulation.
Mar 13 20:33:39 ws2 kernel: qla1280: QLA12160 found on PCI bus 0, dev 9
Mar 13 20:33:39 ws2 kernel: scsi(0): Reading NVRAM
Mar 13 20:33:39 ws2 kernel: scsi(0:0): Resetting SCSI BUS
Mar 13 20:33:39 ws2 kernel: scsi(0:1): Resetting SCSI BUS
Mar 13 20:33:39 ws2 kernel: scsi0 : QLogic QLA12160 PCI to SCSI Host Adapter
Mar 13 20:33:39 ws2 kernel: Firmware version: 10.04.42, Driver
version 3.25
Mar 13 20:33:39 ws2 kernel: Vendor: MAXTOR Model: ATLAS15K2_73SCA
Rev: JNZM
Mar 13 20:33:39 ws2 kernel: Type: Direct-Access
ANSI SCSI revision: 03
Mar 13 20:33:39 ws2 kernel: scsi(0:1:0:0): Sync: period 9, offset 24,
Wide, DT
Mar 13 20:33:39 ws2 kernel: Vendor: FUJITSU Model: MAN3367MP
Rev: 0109
Mar 13 20:33:39 ws2 kernel: Type: Direct-Access
ANSI SCSI revision: 03
Mar 13 20:33:39 ws2 kernel: scsi(0:1:1:0): Sync: period 9, offset 24,
Wide, DT
Mar 13 20:33:39 ws2 kernel: ide-scsi is deprecated for cd burning! Use
ide-cd and give dev=/dev/hdX as device
Mar 13 20:33:39 ws2 kernel: scsi1 : SCSI host adapter emulation for IDE
ATAPI devices
Mar 13 20:33:39 ws2 kernel: Vendor: _NEC Model: DVD_RW ND-4550A
Rev: 1.07
Mar 13 20:33:39 ws2 kernel: Type: CD-ROM
ANSI SCSI revision: 00
Mar 13 20:33:39 ws2 kernel: scsi2 : SCSI host adapter emulation for IDE
ATAPI devices
Mar 13 20:33:39 ws2 kernel: Vendor: HL-DT-ST Model: DVDRAM GMA-4020B
Rev: A109
Mar 13 20:33:39 ws2 kernel: Type: CD-ROM
ANSI SCSI revision: 00
Mar 13 20:33:39 ws2 kernel: SCSI device sda: 143374650 512-byte hdwr
sectors (73408 MB)
Mar 13 20:33:39 ws2 kernel: SCSI device sda: drive cache: write through
Mar 13 20:33:39 ws2 kernel: SCSI device sda: 143374650 512-byte hdwr
sectors (73408 MB)
Mar 13 20:33:39 ws2 kernel: SCSI device sda: drive cache: write through
Mar 13 20:33:39 ws2 kernel: sda: sda1 sda2 sda3 sda4
Mar 13 20:33:39 ws2 kernel: Attached scsi disk sda at scsi0, channel 1,
id 0, lun 0
Mar 13 20:33:39 ws2 kernel: SCSI device sdb: 71771688 512-byte hdwr
sectors (36747 MB)
Mar 13 20:33:39 ws2 kernel: SCSI device sdb: drive cache: write back
Mar 13 20:33:39 ws2 kernel: SCSI device sdb: 71771688 512-byte hdwr
sectors (36747 MB)
Mar 13 20:33:39 ws2 kernel: SCSI device sdb: drive cache: write back
Mar 13 20:33:39 ws2 kernel: sdb: sdb1 sdb2
Mar 13 20:33:39 ws2 kernel: Attached scsi disk sdb at scsi0, channel 1,
id 1, lun 0
Mar 13 20:33:39 ws2 kernel: sr0: scsi3-mmc drive: 0x/0x caddy
Mar 13 20:33:39 ws2 kernel: sr1: scsi3-mmc drive: 0x/0x caddy
Mar 13 20:33:39 ws2 kernel: Attached scsi generic sg0 at scsi0, channel
1, id 0, lun 0, type 0
Mar 13 20:33:39 ws2 kernel: Attached scsi generic sg1 at scsi0, channel
1, id 1, lun 0, type 0
Mar 13 20:33:39 ws2 kernel: Attached scsi generic sg2 at scsi1, channel
0, id 0, lun 0, type 5
Mar 13 20:33:39 ws2 kernel: Attached scsi generic sg3 at scsi2, channel
0, id 0, lun 0, type 5
----------------------------------------------------------------------------------
/proc/interrupts:
CPU0 CPU1
0: 503595 744635 IO-APIC-edge timer
1: 5040 7016 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
8: 2 2 IO-APIC-edge rtc
12: 159728 195845 IO-APIC-edge i8042
14: 28317 29306 IO-APIC-edge ide0
15: 0 13 IO-APIC-edge ide1
16: 15882 15870 IO-APIC-level bttv0, ehci_hcd:usb1
17: 44864 44277 IO-APIC-level qla1280, ohci1394
18: 8 8 IO-APIC-level ohci_hcd:usb2, Ensoniq AudioPCI
19: 19338 19233 IO-APIC-level saa7146 (0), ohci_hcd:usb3,
eth0
NMI: 64670 98880
LOC: 1248159 1248158
ERR: 0
MIS:
----------------------------------------------------------------------------------
/proc/iomem:
00000000-0009e3ff : System RAM
0009e400-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000ccfff : Video ROM
000cd000-000cd7ff : Adapter ROM
000cd800-000cffff : Adapter ROM
000f0000-000fffff : System ROM
00100000-7fffffff : System RAM
00100000-0042edeb : Kernel code
0042edec-0055e44b : Kernel data
88000000-8801ffff : 0000:00:09.0
c0000000-c0000fff : 0000:00:09.0
c0100000-c01fffff : PCI Bus #01
c0100000-c010ffff : 0000:01:05.0
c0110000-c011ffff : 0000:01:05.1
c0120000-c013ffff : 0000:01:05.0
c0200000-c03fffff : PCI Bus #02
c0201000-c02011ff : 0000:02:07.0
c0201000-c02011ff : saa7146
c0201400-c020147f : 0000:02:08.0
c0300000-c03fffff : PCI Bus #03
c0300000-c0300fff : 0000:03:09.0
c0300000-c0300fff : ohci_hcd
c0301000-c0301fff : 0000:03:09.1
c0301000-c0301fff : ohci_hcd
c0302000-c03027ff : 0000:03:08.0
c0302000-c03027ff : ohci1394
c0302800-c03028ff : 0000:03:09.2
c0302800-c03028ff : ehci_hcd
c0600000-c0600fff : 0000:00:00.0
c4000000-c7ffffff : 0000:00:00.0
d0000000-efffffff : PCI Bus #01
d0000000-dfffffff : 0000:01:05.0
d0000000-dfffffff : vesafb
e0000000-efffffff : 0000:01:05.1
f0000000-f00fffff : PCI Bus #02
f0000000-f0000fff : 0000:02:04.0
f0000000-f0000fff : bttv0
f0001000-f0001fff : 0000:02:04.1
f0020000-f003ffff : 0000:02:08.0
fec00000-fec07fff : reserved
fee00000-fee00fff : reserved
fff80000-ffffffff : reserved
----------------------------------------------------------------------------------
/proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial
0c00-0c07 : w83627hf
0cf8-0cff : PCI conf1
1000-10ff : 0000:00:09.0
1410-1413 : 0000:00:00.0
2000-2fff : PCI Bus #01
2000-20ff : 0000:01:05.0
3000-4fff : PCI Bus #02
3000-307f : 0000:02:08.0
3000-307f : 0000:02:08.0
3080-30bf : 0000:02:06.0
3080-30bf : Ensoniq AudioPCI
4000-4fff : PCI Bus #03
4000-407f : 0000:03:08.0
80e0-80ef : amd756-smbus
f000-f00f : 0000:00:07.1
f000-f007 : ide0
f008-f00f : ide1
----------------------------------------------------------------------------------
/proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : AMD Athlon(tm) MP 2800+
stepping : 0
cpu MHz : 2133.684
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse syscall mp mmxext 3dnowext 3dnow
bogomips : 4276.53
processor : 1
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : AMD Athlon(tm) Processor
stepping : 0
cpu MHz : 2133.684
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse syscall mp mmxext 3dnowext 3dnow
bogomips : 4267.23
----------------------------------------------------------------------------------
lspci -vvv
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP
[IGD4-2P] System Controller (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at c4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at c0600000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at 1410 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit-
FW- Rate=x4
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP
[IGD4-2P] AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: d0000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA
(rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus]
IDE (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at f000 [size=16]
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI
(rev 03)
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:00:09.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel
Ultra3 SCSI Processor (rev 06)
Subsystem: QLogic Corp.: Unknown device 0007
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at c0000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 88000000 [disabled] [size=128K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI
(rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=03, sec-latency=69
I/O behind bridge: 00003000-00004fff
Memory behind bridge: c0200000-c03fffff
Prefetchable memory behind bridge: f0000000-f00fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:01:05.0 VGA compatible controller: ATI Technologies Inc RV350 AP
[Radeon 9600] (prog-if 00 [VGA])
Subsystem: C.P. Technology Co. Ltd PowerColor R96A-C3N
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at c0120000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit-
FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:05.1 Display controller: ATI Technologies Inc RV350 AP [Radeon
9600] (Secondary)
Subsystem: C.P. Technology Co. Ltd: Unknown device 2065
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at c0110000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.0 Multimedia video controller: Brooktree Corporation Bt878
Video Capture (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=4K]
0000:02:04.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0001000 (32-bit, prefetchable) [size=4K]
0000:02:05.0 PCI bridge: Hint Corp HB6 Universal PCI-PCI bridge
(non-transparent mode) (rev 11) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: c0300000-c03fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [90] #06 [0080]
0000:02:06.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 3080 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:07.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: TERRATEC Electronic GmbH: Unknown device 1156
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c0201000 (32-bit, non-prefetchable) [size=512]
0000:02:08.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M
[Tornado] (rev 78)
Subsystem: Tyan Computer Tiger MPX S2466 (3C920 Integrated Fast
Ethernet Controller)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 0x10 (64
bytes)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 3000 [size=128]
Region 1: Memory at c0201400 (32-bit, non-prefetchable) [size=128]
Expansion ROM at f0020000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:03:08.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c0302000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at 4000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:03:09.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10
[OHCI])
Subsystem: Unknown device 2098:2100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x10 (64
bytes)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c0300000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:03:09.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10
[OHCI])
Subsystem: Unknown device 2098:2100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x10 (64
bytes)
Interrupt: pin B routed to IRQ 19
Region 0: Memory at c0301000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:03:09.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if
20 [EHCI])
Subsystem: Unknown device 2098:2000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 132 (4000ns min, 8500ns max), Cache Line Size: 0x10
(64 bytes)
Interrupt: pin C routed to IRQ 16
Region 0: Memory at c0302800 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
----------------------------------------------------------------------------------
ver_linux output (Debian 3.1 system)
Gnu C 3.3.5
Gnu make 3.80
binutils 2.15
util-linux 2.12p
mount 2.12p
module-init-tools 3.2-pre1
e2fsprogs 1.37
reiserfsprogs line
reiser4progs line
PPP 2.4.3
nfs-utils 1.0.6
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 3.2.1
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.2.1
Modules Loaded
reply other threads:[~2006-03-13 22:55 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4415F863.9040203@simg.de \
--to=stefan-kernel@simg.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.