From: Sergei Shtylyov <sshtylyov@ru.mvista.com>
To: jgarzik@pobox.com
Cc: Rodolfo Giometti <giometti@linux.it>,
netdev@vger.kernel.org, Linux-MIPS <linux-mips@linux-mips.org>
Subject: [PATCH] au1000_eth.c probe code straightened up
Date: Wed, 19 Apr 2006 22:46:21 +0400 [thread overview]
Message-ID: <4446857D.90507@ru.mvista.com> (raw)
In-Reply-To: <20060406155011.GC23424@enneenne.com>
[-- Attachment #1: Type: text/plain, Size: 429 bytes --]
Straighten up the AMD Au1xx0 Ethernet probing code, make it print out (and
store in the 'net_device' structure) the physical address of the controller,
not the KSEG1-based virtual. Make the driver also claim/release the 4-byte MAC
enable registers and assign to the Ethernet ports two consecutive MAC
addresses to match those that are printed on their stickers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[-- Attachment #2: au1000_eth-probe-rewrite.patch --]
[-- Type: text/plain, Size: 10374 bytes --]
diff --git a/drivers/net/au1000_eth.c b/drivers/net/au1000_eth.c
index 1363083..d5dfc78 100644
--- a/drivers/net/au1000_eth.c
+++ b/drivers/net/au1000_eth.c
@@ -2,7 +2,7 @@
*
* Alchemy Au1x00 ethernet driver
*
- * Copyright 2001,2002,2003 MontaVista Software Inc.
+ * Copyright 2001-2003, 2006 MontaVista Software Inc.
* Copyright 2002 TimeSys Corp.
* Added ethtool/mii-tool support,
* Copyright 2004 Matt Porter <mporter@kernel.crashing.org>
@@ -67,7 +67,7 @@ static int au1000_debug = 5;
static int au1000_debug = 3;
#endif
-#define DRV_NAME "au1000eth"
+#define DRV_NAME "au1000_eth"
#define DRV_VERSION "1.5"
#define DRV_AUTHOR "Pete Popov <ppopov@embeddedalley.com>"
#define DRV_DESC "Au1xxx on-chip Ethernet driver"
@@ -79,7 +79,7 @@ MODULE_LICENSE("GPL");
// prototypes
static void hard_stop(struct net_device *);
static void enable_rx_tx(struct net_device *dev);
-static struct net_device * au1000_probe(u32 ioaddr, int irq, int port_num);
+static struct net_device * au1000_probe(int port_num);
static int au1000_init(struct net_device *);
static int au1000_open(struct net_device *);
static int au1000_close(struct net_device *);
@@ -1159,12 +1159,27 @@ setup_hw_rings(struct au1000_private *au
}
static struct {
- int port;
u32 base_addr;
u32 macen_addr;
int irq;
struct net_device *dev;
-} iflist[2];
+} iflist[2] = {
+#ifdef CONFIG_SOC_AU1000
+ {AU1000_ETH0_BASE, AU1000_MAC0_ENABLE, AU1000_MAC0_DMA_INT},
+ {AU1000_ETH1_BASE, AU1000_MAC1_ENABLE, AU1000_MAC1_DMA_INT}
+#endif
+#ifdef CONFIG_SOC_AU1100
+ {AU1100_ETH0_BASE, AU1100_MAC0_ENABLE, AU1100_MAC0_DMA_INT}
+#endif
+#ifdef CONFIG_SOC_AU1500
+ {AU1500_ETH0_BASE, AU1500_MAC0_ENABLE, AU1500_MAC0_DMA_INT},
+ {AU1500_ETH1_BASE, AU1500_MAC1_ENABLE, AU1500_MAC1_DMA_INT}
+#endif
+#ifdef CONFIG_SOC_AU1550
+ {AU1550_ETH0_BASE, AU1550_MAC0_ENABLE, AU1550_MAC0_DMA_INT},
+ {AU1550_ETH1_BASE, AU1550_MAC1_ENABLE, AU1550_MAC1_DMA_INT}
+#endif
+};
static int num_ifs;
@@ -1175,58 +1190,14 @@ static int num_ifs;
*/
static int __init au1000_init_module(void)
{
- struct cpuinfo_mips *c = ¤t_cpu_data;
int ni = (int)((au_readl(SYS_PINFUNC) & (u32)(SYS_PF_NI2)) >> 4);
struct net_device *dev;
int i, found_one = 0;
- switch (c->cputype) {
-#ifdef CONFIG_SOC_AU1000
- case CPU_AU1000:
- num_ifs = 2 - ni;
- iflist[0].base_addr = AU1000_ETH0_BASE;
- iflist[1].base_addr = AU1000_ETH1_BASE;
- iflist[0].macen_addr = AU1000_MAC0_ENABLE;
- iflist[1].macen_addr = AU1000_MAC1_ENABLE;
- iflist[0].irq = AU1000_MAC0_DMA_INT;
- iflist[1].irq = AU1000_MAC1_DMA_INT;
- break;
-#endif
-#ifdef CONFIG_SOC_AU1100
- case CPU_AU1100:
- num_ifs = 1 - ni;
- iflist[0].base_addr = AU1100_ETH0_BASE;
- iflist[0].macen_addr = AU1100_MAC0_ENABLE;
- iflist[0].irq = AU1100_MAC0_DMA_INT;
- break;
-#endif
-#ifdef CONFIG_SOC_AU1500
- case CPU_AU1500:
- num_ifs = 2 - ni;
- iflist[0].base_addr = AU1500_ETH0_BASE;
- iflist[1].base_addr = AU1500_ETH1_BASE;
- iflist[0].macen_addr = AU1500_MAC0_ENABLE;
- iflist[1].macen_addr = AU1500_MAC1_ENABLE;
- iflist[0].irq = AU1500_MAC0_DMA_INT;
- iflist[1].irq = AU1500_MAC1_DMA_INT;
- break;
-#endif
-#ifdef CONFIG_SOC_AU1550
- case CPU_AU1550:
- num_ifs = 2 - ni;
- iflist[0].base_addr = AU1550_ETH0_BASE;
- iflist[1].base_addr = AU1550_ETH1_BASE;
- iflist[0].macen_addr = AU1550_MAC0_ENABLE;
- iflist[1].macen_addr = AU1550_MAC1_ENABLE;
- iflist[0].irq = AU1550_MAC0_DMA_INT;
- iflist[1].irq = AU1550_MAC1_DMA_INT;
- break;
-#endif
- default:
- num_ifs = 0;
- }
+ num_ifs = NUM_ETH_INTERFACES - ni;
+
for(i = 0; i < num_ifs; i++) {
- dev = au1000_probe(iflist[i].base_addr, iflist[i].irq, i);
+ dev = au1000_probe(i);
iflist[i].dev = dev;
if (dev)
found_one++;
@@ -1435,8 +1406,7 @@ static struct ethtool_ops au1000_ethtool
.get_link = au1000_get_link
};
-static struct net_device *
-au1000_probe(u32 ioaddr, int irq, int port_num)
+static struct net_device * au1000_probe(int port_num)
{
static unsigned version_printed = 0;
struct au1000_private *aup = NULL;
@@ -1444,94 +1414,95 @@ au1000_probe(u32 ioaddr, int irq, int po
db_dest_t *pDB, *pDBfree;
char *pmac, *argptr;
char ethaddr[6];
- int i, err;
+ int irq, i, err;
+ u32 base, macen;
+
+ if (port_num >= NUM_ETH_INTERFACES)
+ return NULL;
- if (!request_mem_region(CPHYSADDR(ioaddr), MAC_IOSIZE, "Au1x00 ENET"))
+ base = CPHYSADDR(iflist[port_num].base_addr );
+ macen = CPHYSADDR(iflist[port_num].macen_addr);
+ irq = iflist[port_num].irq;
+
+ if (!request_mem_region( base, MAC_IOSIZE, "Au1x00 ENET") ||
+ !request_mem_region(macen, 4, "Au1x00 ENET"))
return NULL;
- if (version_printed++ == 0)
+ if (version_printed++ == 0)
printk("%s version %s %s\n", DRV_NAME, DRV_VERSION, DRV_AUTHOR);
dev = alloc_etherdev(sizeof(struct au1000_private));
if (!dev) {
- printk (KERN_ERR "au1000 eth: alloc_etherdev failed\n");
+ printk(KERN_ERR "%s: alloc_etherdev failed\n", DRV_NAME);
return NULL;
}
- if ((err = register_netdev(dev))) {
- printk(KERN_ERR "Au1x_eth Cannot register net device err %d\n",
- err);
+ if ((err = register_netdev(dev)) != 0) {
+ printk(KERN_ERR "%s: Cannot register net device, error %d\n",
+ DRV_NAME, err);
free_netdev(dev);
return NULL;
}
- printk("%s: Au1x Ethernet found at 0x%x, irq %d\n",
- dev->name, ioaddr, irq);
+ printk("%s: Au1xx0 Ethernet found at 0x%x, irq %d\n",
+ dev->name, base, irq);
aup = dev->priv;
/* Allocate the data buffers */
/* Snooping works fine with eth on all au1xxx */
- aup->vaddr = (u32)dma_alloc_noncoherent(NULL,
- MAX_BUF_SIZE * (NUM_TX_BUFFS+NUM_RX_BUFFS),
- &aup->dma_addr,
- 0);
+ aup->vaddr = (u32)dma_alloc_noncoherent(NULL, MAX_BUF_SIZE *
+ (NUM_TX_BUFFS + NUM_RX_BUFFS),
+ &aup->dma_addr, 0);
if (!aup->vaddr) {
free_netdev(dev);
- release_mem_region(CPHYSADDR(ioaddr), MAC_IOSIZE);
+ release_mem_region( base, MAC_IOSIZE);
+ release_mem_region(macen, 4);
return NULL;
}
/* aup->mac is the base address of the MAC's registers */
- aup->mac = (volatile mac_reg_t *)((unsigned long)ioaddr);
+ aup->mac = (volatile mac_reg_t *)iflist[port_num].base_addr;
+
/* Setup some variables for quick register address access */
- if (ioaddr == iflist[0].base_addr)
- {
- /* check env variables first */
- if (!get_ethernet_addr(ethaddr)) {
+ aup->enable = (volatile u32 *)iflist[port_num].macen_addr;
+ aup->mac_id = port_num;
+ au_macs[port_num] = aup;
+
+ if (port_num == 0) {
+ /* Check the environment variables first */
+ if (get_ethernet_addr(ethaddr) == 0)
memcpy(au1000_mac_addr, ethaddr, sizeof(au1000_mac_addr));
- } else {
+ else {
/* Check command line */
argptr = prom_getcmdline();
- if ((pmac = strstr(argptr, "ethaddr=")) == NULL) {
- printk(KERN_INFO "%s: No mac address found\n",
- dev->name);
- /* use the hard coded mac addresses */
- } else {
+ if ((pmac = strstr(argptr, "ethaddr=")) == NULL)
+ printk(KERN_INFO "%s: No MAC address found\n",
+ dev->name);
+ /* Use the hard coded MAC addresses */
+ else {
str2eaddr(ethaddr, pmac + strlen("ethaddr="));
memcpy(au1000_mac_addr, ethaddr,
- sizeof(au1000_mac_addr));
+ sizeof(au1000_mac_addr));
}
}
- aup->enable = (volatile u32 *)
- ((unsigned long)iflist[0].macen_addr);
- memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr));
+
setup_hw_rings(aup, MAC0_RX_DMA_ADDR, MAC0_TX_DMA_ADDR);
- aup->mac_id = 0;
- au_macs[0] = aup;
- }
- else
- if (ioaddr == iflist[1].base_addr)
- {
- aup->enable = (volatile u32 *)
- ((unsigned long)iflist[1].macen_addr);
- memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr));
- dev->dev_addr[4] += 0x10;
+ } else if (port_num == 1)
setup_hw_rings(aup, MAC1_RX_DMA_ADDR, MAC1_TX_DMA_ADDR);
- aup->mac_id = 1;
- au_macs[1] = aup;
- }
- else
- {
- printk(KERN_ERR "%s: bad ioaddr\n", dev->name);
- }
- /* bring the device out of reset, otherwise probing the mii
- * will hang */
+ /*
+ * Assign to the Ethernet ports two consecutive MAC addresses
+ * to match those that are printed on their stickers
+ */
+ memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr));
+ dev->dev_addr[5] += port_num;
+
+ /* Bring the device out of reset, otherwise probing the MII will hang */
*aup->enable = MAC_EN_CLOCK_ENABLE;
au_sync_delay(2);
- *aup->enable = MAC_EN_RESET0 | MAC_EN_RESET1 |
- MAC_EN_RESET2 | MAC_EN_CLOCK_ENABLE;
+ *aup->enable = MAC_EN_RESET0 | MAC_EN_RESET1 | MAC_EN_RESET2 |
+ MAC_EN_CLOCK_ENABLE;
au_sync_delay(2);
aup->mii = kmalloc(sizeof(struct mii_phy), GFP_KERNEL);
@@ -1580,7 +1551,7 @@ au1000_probe(u32 ioaddr, int irq, int po
}
spin_lock_init(&aup->lock);
- dev->base_addr = ioaddr;
+ dev->base_addr = base;
dev->irq = irq;
dev->open = au1000_open;
dev->hard_start_xmit = au1000_tx;
@@ -1614,13 +1585,12 @@ err_out:
if (aup->tx_db_inuse[i])
ReleaseDB(aup, aup->tx_db_inuse[i]);
}
- dma_free_noncoherent(NULL,
- MAX_BUF_SIZE * (NUM_TX_BUFFS+NUM_RX_BUFFS),
- (void *)aup->vaddr,
- aup->dma_addr);
+ dma_free_noncoherent(NULL, MAX_BUF_SIZE * (NUM_TX_BUFFS + NUM_RX_BUFFS),
+ (void *)aup->vaddr, aup->dma_addr);
unregister_netdev(dev);
free_netdev(dev);
- release_mem_region(CPHYSADDR(ioaddr), MAC_IOSIZE);
+ release_mem_region( base, MAC_IOSIZE);
+ release_mem_region(macen, 4);
return NULL;
}
@@ -1805,20 +1775,18 @@ static void __exit au1000_cleanup_module
aup = (struct au1000_private *) dev->priv;
unregister_netdev(dev);
kfree(aup->mii);
- for (j = 0; j < NUM_RX_DMA; j++) {
+ for (j = 0; j < NUM_RX_DMA; j++)
if (aup->rx_db_inuse[j])
ReleaseDB(aup, aup->rx_db_inuse[j]);
- }
- for (j = 0; j < NUM_TX_DMA; j++) {
+ for (j = 0; j < NUM_TX_DMA; j++)
if (aup->tx_db_inuse[j])
ReleaseDB(aup, aup->tx_db_inuse[j]);
- }
- dma_free_noncoherent(NULL,
- MAX_BUF_SIZE * (NUM_TX_BUFFS+NUM_RX_BUFFS),
- (void *)aup->vaddr,
- aup->dma_addr);
+ dma_free_noncoherent(NULL, MAX_BUF_SIZE *
+ (NUM_TX_BUFFS + NUM_RX_BUFFS),
+ (void *)aup->vaddr, aup->dma_addr);
+ release_mem_region(dev->base_addr, MAC_IOSIZE);
+ release_mem_region(CPHYSADDR(iflist[i].macen_addr), 4);
free_netdev(dev);
- release_mem_region(CPHYSADDR(iflist[i].base_addr), MAC_IOSIZE);
}
}
}
next prev parent reply other threads:[~2006-04-19 18:35 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-04-05 15:47 Power management for au1000_eth.c Rodolfo Giometti
2006-04-05 22:23 ` Rodolfo Giometti
2006-04-05 22:26 ` [PATCH] Oops! - " Rodolfo Giometti
2006-04-06 14:43 ` Sergei Shtylyov
2006-04-06 15:50 ` Rodolfo Giometti
2006-04-19 18:46 ` Sergei Shtylyov [this message]
2006-05-02 15:09 ` [PATCH] au1000_eth.c Power Management, driver registration and module support Rodolfo Giometti
2006-05-03 7:47 ` Rodolfo Giometti
2006-05-31 15:01 ` Sergei Shtylyov
2006-05-31 15:21 ` Rodolfo Giometti
2006-04-06 17:10 ` Oops! - Re: Power management for au1000_eth.c Jordan Crouse
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4446857D.90507@ru.mvista.com \
--to=sshtylyov@ru.mvista.com \
--cc=giometti@linux.it \
--cc=jgarzik@pobox.com \
--cc=linux-mips@linux-mips.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.