From: rod@morison.biz (Rod Morison)
To: lm-sensors@vger.kernel.org
Subject: [lm-sensors] w83792d works under 2.6 kernel, but not 2.4 kernel
Date: Tue, 23 May 2006 13:25:08 +0000 [thread overview]
Message-ID: <44730D34.4080802@morison.biz> (raw)
I am stuck with what it certainly a config problem. I've got lm_sensors
2.10.0 running fine on a SuperMicro PDSMA mobo under 2.6.16 kernel.
However, under 2.4.19 (required for the embedded project I'm on), I'm
missing sensors for one of the chips. I'm using the same sensors.conf
and modules.conf/modprobe.conf settings.
In the 2.4 kernel case I get some eeprom/ram listings off the I801 bus,
instead of the w83792d chip I'm expecting.
Can anyone point me in the right direction to reconcile the difference...
2.6 kernel driver list and sensors output:
sm1:~ # lsmod
Module Size Used by
joydev 27520 0
st 55332 0
sr_mod 33060 0
xt_pkttype 18560 3
ipt_LOG 23168 9
xt_limit 19328 9
w83627hf 45328 0
eeprom 24464 0
w83792d 46872 0
w83781d 53156 0
hwmon_vid 19200 2 w83627hf,w83781d
hwmon 19848 3 w83627hf,w83792d,w83781d
i2c_isa 22272 2 w83627hf,w83781d
af_packet 55820 2
edd 26760 0
button 24224 0
battery 27272 0
ac 22152 0
ip6t_REJECT 22272 3
xt_tcpudp 19968 5
ipt_REJECT 22272 3
xt_state 18816 12
iptable_mangle 19584 0
iptable_nat 25220 0
ip_nat 35884 1 iptable_nat
iptable_filter 19712 1
ip6table_mangle 19072 0
ip_conntrack 75164 3 xt_state,iptable_nat,ip_nat
nfnetlink 23496 2 ip_nat,ip_conntrack
ip_tables 30792 3 iptable_mangle,iptable_nat,iptable_filter
ip6table_filter 19584 1
ip6_tables 32328 2 ip6table_mangle,ip6table_filter
x_tables 31368 10
xt_pkttype,ipt_LOG,xt_limit,ip6t_REJECT,xt_tcpudp,ipt_REJECT,xt_state,iptable_nat,ip_tables,ip6_tables
ipv6 328736 19 ip6t_REJECT
apparmor 72352 0
aamatch_pcre 30720 1 apparmor
loop 32528 0
dm_mod 77616 0
i2c_i801 25876 0
shpchp 62368 0
e1000 130744 0
uhci_hcd 48544 0
ehci_hcd 47624 0
ide_cd 57248 0
cdrom 52392 2 sr_mod,ide_cd
i2c_core 40192 6
w83627hf,eeprom,w83792d,w83781d,i2c_isa,i2c_i801
pci_hotplug 45056 1 shpchp
i8xx_tco 24616 0
usbcore 150312 3 uhci_hcd,ehci_hcd
floppy 82984 0
parport_pc 56680 1
lp 29768 0
parport 56716 2 parport_pc,lp
reiserfs 241280 2
fan 21896 0
thermal 32272 0
sg 52264 0
processor 50280 1 thermal
3w_9xxx 50180 3
piix 27652 0 [permanent]
sd_mod 34176 4
scsi_mod 163888 5 st,sr_mod,sg,3w_9xxx,sd_mod
ide_disk 32896 0
ide_core 165764 3 ide_cd,piix,ide_disk
sm1:~ # sensors
w83627hf-isa-0290
Adapter: ISA adapter
VCore 1: +0.14 V (min = +1.38 V, max = +1.54 V) ALARM
VCore 2: +0.14 V (min = +1.38 V, max = +1.54 V) ALARM
+3.3V: +0.14 V (min = +3.14 V, max = +3.46 V) ALARM
+5V: +5.19 V (min = +4.73 V, max = +5.24 V)
+12V: +0.55 V (min = +10.82 V, max = +13.19 V) ALARM
-12V: -14.17 V (min = -13.18 V, max = -10.88 V) ALARM
-5V: -7.26 V (min = -5.25 V, max = -4.75 V) ALARM
V5SB: +5.54 V (min = +4.73 V, max = +5.24 V) ALARM
VBat: +0.00 V (min = +2.40 V, max = +3.60 V) ALARM
fan1: 0 RPM (min = 2848 RPM, div = 2) ALARM
fan2: 0 RPM (min = 2848 RPM, div = 2) ALARM
fan3: 0 RPM (min = 1328 RPM, div = 8) ALARM
temp1: +124?C (high = -5?C, hyst = -3?C) sensor =
thermistor ALARM
temp2: +124.0?C (high = +80?C, hyst = +75?C) sensor =
thermistor ALARM
temp3: +124.0?C (high = +80?C, hyst = +75?C) sensor =
thermistor ALARM
vid: +1.462 V (VRM Version 10.0)
alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm disabled
w83792d-i2c-0-2f
Adapter: SMBus I801 adapter at 1100
VCoreA: +1.33 V (min = +1.40 V, max = +1.60 V) ALARM
VCoreB: +1.53 V (min = +1.40 V, max = +1.60 V)
VIN0: +3.29 V (min = +3.20 V, max = +3.39 V)
VIN1: +3.01 V (min = +3.09 V, max = +3.30 V) ALARM
VIN2: +0.52 V (min = +1.39 V, max = +1.49 V) ALARM
VIN3: +3.12 V (min = +2.59 V, max = +2.64 V) ALARM
5VCC: +5.02 V (min = +4.73 V, max = +5.23 V)
5VSB: +4.88 V (min = +4.73 V, max = +5.23 V)
VBAT: +3.20 V (min = +2.85 V, max = +3.14 V) ALARM
Fan1: 0 RPM (min = 712 RPM, div = 8) ALARM
Fan2: 0 RPM (min = 712 RPM, div = 8) ALARM
Fan3: 7336 RPM (min = 712 RPM, div = 8)
Fan4: 0 RPM (min = 712 RPM, div = 8) ALARM
Fan5: 0 RPM (min = 712 RPM, div = 8) ALARM
Fan6: 5625 RPM (min = 712 RPM, div = 8)
ERROR: Can't get FAN7 data!
Temp1: +34.0?C (high = +50.0?C, hyst = +0.0?C)
Temp2: +41.0?C (high = +80.0?C, hyst = +75.0?C)
Temp3: +28.5?C (high = +80.0?C, hyst = +75.0?C)
chassis: Chassis intrusion detection ALARM
sm1:~ #
--------------------------------------------------------------------------------------
2.4 kernel driver list and sensors output
2.4.19# lsmod
Module Size Used by Tainted: P
w83627hf 14104 0 (unused)
smbus-arp 4816 0 (unused)
i2c-isa 804 0 (unused)
i2c-i801 4828 0 (unused)
eeprom 3500 0 (unused)
w83781d 19196 0 (unused)
i2c-proc 5988 0 [w83627hf smbus-arp eeprom w83781d]
i2c-core 14276 0 [w83627hf smbus-arp i2c-isa i2c-i801
eeprom w83781d i2c-proc]
e1000 98896 1
2.4.19# sensors
eeprom-i2c-0-50
Adapter: SMBus I801 adapter at 1100
Memory type: DDR2 SDRAM DIMM
Memory size (MB): 512
eeprom-i2c-0-52
Adapter: SMBus I801 adapter at 1100
Memory type: DDR2 SDRAM DIMM
Memory size (MB): 512
w83627hf-isa-0290
Adapter: ISA adapter
in0: +0.00 V (min = +3.28 V, max = +3.68 V)
in1: +0.00 V (min = +3.28 V, max = +3.68 V)
in2: +0.00 V (min = +2.82 V, max = +3.79 V)
in3: +3.09 V (min = +4.08 V, max = +4.08 V)
in4: +0.00 V (min = +4.08 V, max = +4.08 V)
in5: +0.00 V (min = +4.08 V, max = +4.08 V)
in6: +0.00 V (min = +4.08 V, max = +4.08 V)
in7: +3.31 V (min = +4.08 V, max = +4.08 V)
in8: +0.00 V (min = +4.08 V, max = +4.08 V)
fan1: 0 RPM (min = 2848 RPM, div = 2)
fan2: 0 RPM (min = 2848 RPM, div = 2)
fan3: 0 RPM (min = 0 RPM, div = 8)
temp1: +127 C (high = -1 C, hyst = -1 C) sensor =
thermistor
temp2: +127.0 C (high = +80 C, hyst = +75 C) sensor =
thermistor ALARM
temp3: +127.0 C (high = +80 C, hyst = +75 C) sensor =
thermistor ALARM
vid: +3.500 V (VRM Version 8.2)
alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm disabled
arp-i2c-0-61
Adapter: SMBus I801 adapter at 1100
next reply other threads:[~2006-05-23 13:25 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-05-23 13:25 Rod Morison [this message]
2006-05-23 21:21 ` [lm-sensors] w83792d works under 2.6 kernel, but not 2.4 kernel Rudolf Marek
2006-05-24 8:32 ` Rod Morison
2006-05-24 8:45 ` Yuan Mu
2006-05-24 14:13 ` Rod Morison
2006-05-24 15:07 ` Rudolf Marek
2006-05-25 6:57 ` Rod Morison
2006-05-25 21:25 ` Rudolf Marek
2006-05-25 22:42 ` Rod Morison
2006-05-26 6:18 ` Rudolf Marek
2006-05-31 15:09 ` Rudolf Marek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=44730D34.4080802@morison.biz \
--to=rod@morison.biz \
--cc=lm-sensors@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.