From: Philip Craig <philipc@snapgear.com>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: netdev@vger.kernel.org
Subject: [PATCH 2/2] 8139cp: add ethtool eeprom support
Date: Wed, 14 Jun 2006 16:43:08 +1000 [thread overview]
Message-ID: <448FAFFC.7070006@snapgear.com> (raw)
Implement the ethtool eeprom operations for the 8139cp driver.
Tested on x86 and big-endian ARM.
Signed-off-by: Philip Craig <philipc@snapgear.com>
Index: linux-2.6.17-rc6/drivers/net/8139cp.c
===================================================================
--- linux-2.6.17-rc6.orig/drivers/net/8139cp.c 2006-06-14 15:59:26.000000000 +1000
+++ linux-2.6.17-rc6/drivers/net/8139cp.c 2006-06-14 15:59:53.000000000 +1000
@@ -401,6 +401,11 @@ static void cp_clean_rings (struct cp_pr
#ifdef CONFIG_NET_POLL_CONTROLLER
static void cp_poll_controller(struct net_device *dev);
#endif
+static int cp_get_eeprom_len(struct net_device *dev);
+static int cp_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data);
+static int cp_set_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data);
static struct pci_device_id cp_pci_tbl[] = {
{ PCI_VENDOR_ID_REALTEK, PCI_DEVICE_ID_REALTEK_8139,
@@ -1577,6 +1582,9 @@ static struct ethtool_ops cp_ethtool_ops
.get_strings = cp_get_strings,
.get_ethtool_stats = cp_get_ethtool_stats,
.get_perm_addr = ethtool_op_get_perm_addr,
+ .get_eeprom_len = cp_get_eeprom_len,
+ .get_eeprom = cp_get_eeprom,
+ .set_eeprom = cp_set_eeprom,
};
static int cp_ioctl (struct net_device *dev, struct ifreq *rq, int cmd)
@@ -1612,24 +1620,32 @@ static int cp_ioctl (struct net_device *
#define eeprom_delay() readl(ee_addr)
/* The EEPROM commands include the alway-set leading bit. */
+#define EE_EXTEND_CMD (4)
#define EE_WRITE_CMD (5)
#define EE_READ_CMD (6)
#define EE_ERASE_CMD (7)
-static int read_eeprom (void __iomem *ioaddr, int location, int addr_len)
-{
- int i;
- unsigned retval = 0;
- void __iomem *ee_addr = ioaddr + Cfg9346;
- int read_cmd = location | (EE_READ_CMD << addr_len);
+#define EE_EWDS_ADDR (0)
+#define EE_WRAL_ADDR (1)
+#define EE_ERAL_ADDR (2)
+#define EE_EWEN_ADDR (3)
+
+#define CP_EEPROM_MAGIC PCI_DEVICE_ID_REALTEK_8139
+static void eeprom_cmd_start(void __iomem *ee_addr)
+{
writeb (EE_ENB & ~EE_CS, ee_addr);
writeb (EE_ENB, ee_addr);
eeprom_delay ();
+}
+
+static void eeprom_cmd(void __iomem *ee_addr, int cmd, int cmd_len)
+{
+ int i;
- /* Shift the read command bits out. */
- for (i = 3 + addr_len - 1; i >= 0; i--) {
- int dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
+ /* Shift the command bits out. */
+ for (i = cmd_len - 1; i >= 0; i--) {
+ int dataval = (cmd & (1 << i)) ? EE_DATA_WRITE : 0;
writeb (EE_ENB | dataval, ee_addr);
eeprom_delay ();
writeb (EE_ENB | dataval | EE_SHIFT_CLK, ee_addr);
@@ -1637,6 +1653,33 @@ static int read_eeprom (void __iomem *io
}
writeb (EE_ENB, ee_addr);
eeprom_delay ();
+}
+
+static void eeprom_cmd_end(void __iomem *ee_addr)
+{
+ writeb (~EE_CS, ee_addr);
+ eeprom_delay ();
+}
+
+static void eeprom_extend_cmd(void __iomem *ee_addr, int extend_cmd,
+ int addr_len)
+{
+ int cmd = (EE_EXTEND_CMD << addr_len) | (extend_cmd << (addr_len - 2));
+
+ eeprom_cmd_start(ee_addr);
+ eeprom_cmd(ee_addr, cmd, 3 + addr_len);
+ eeprom_cmd_end(ee_addr);
+}
+
+static u16 read_eeprom (void __iomem *ioaddr, int location, int addr_len)
+{
+ int i;
+ u16 retval = 0;
+ void __iomem *ee_addr = ioaddr + Cfg9346;
+ int read_cmd = location | (EE_READ_CMD << addr_len);
+
+ eeprom_cmd_start(ee_addr);
+ eeprom_cmd(ee_addr, read_cmd, 3 + addr_len);
for (i = 16; i > 0; i--) {
writeb (EE_ENB | EE_SHIFT_CLK, ee_addr);
@@ -1648,13 +1691,125 @@ static int read_eeprom (void __iomem *io
eeprom_delay ();
}
- /* Terminate the EEPROM access. */
- writeb (~EE_CS, ee_addr);
- eeprom_delay ();
+ eeprom_cmd_end(ee_addr);
return retval;
}
+static void write_eeprom(void __iomem *ioaddr, int location, u16 val,
+ int addr_len)
+{
+ int i;
+ void __iomem *ee_addr = ioaddr + Cfg9346;
+ int write_cmd = location | (EE_WRITE_CMD << addr_len);
+
+ eeprom_extend_cmd(ee_addr, EE_EWEN_ADDR, addr_len);
+
+ eeprom_cmd_start(ee_addr);
+ eeprom_cmd(ee_addr, write_cmd, 3 + addr_len);
+ eeprom_cmd(ee_addr, val, 16);
+ eeprom_cmd_end(ee_addr);
+
+ eeprom_cmd_start(ee_addr);
+ for (i = 0; i < 20000; i++)
+ if (readb(ee_addr) & EE_DATA_READ)
+ break;
+ eeprom_cmd_end(ee_addr);
+
+ eeprom_extend_cmd(ee_addr, EE_EWDS_ADDR, addr_len);
+}
+
+static int cp_get_eeprom_len(struct net_device *dev)
+{
+ struct cp_private *cp = netdev_priv(dev);
+ int size;
+
+ spin_lock_irq(&cp->lock);
+ size = read_eeprom(cp->regs, 0, 8) == 0x8129 ? 256 : 128;
+ spin_unlock_irq(&cp->lock);
+
+ return size;
+}
+
+static int cp_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ struct cp_private *cp = netdev_priv(dev);
+ unsigned int addr_len;
+ u16 val;
+ u32 offset = eeprom->offset >> 1;
+ u32 len = eeprom->len;
+ u32 i = 0;
+
+ eeprom->magic = CP_EEPROM_MAGIC;
+
+ spin_lock_irq(&cp->lock);
+
+ addr_len = read_eeprom(cp->regs, 0, 8) == 0x8129 ? 8 : 6;
+
+ if (eeprom->offset & 1) {
+ val = read_eeprom(cp->regs, offset, addr_len);
+ data[i++] = (u8)(val >> 8);
+ offset++;
+ }
+
+ while (i < len - 1) {
+ val = read_eeprom(cp->regs, offset, addr_len);
+ data[i++] = (u8)val;
+ data[i++] = (u8)(val >> 8);
+ offset++;
+ }
+
+ if (i < len) {
+ val = read_eeprom(cp->regs, offset, addr_len);
+ data[i] = (u8)val;
+ }
+
+ spin_unlock_irq(&cp->lock);
+ return 0;
+}
+
+static int cp_set_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ struct cp_private *cp = netdev_priv(dev);
+ unsigned int addr_len;
+ u16 val;
+ u32 offset = eeprom->offset >> 1;
+ u32 len = eeprom->len;
+ u32 i = 0;
+
+ if (eeprom->magic != CP_EEPROM_MAGIC)
+ return -EINVAL;
+
+ spin_lock_irq(&cp->lock);
+
+ addr_len = read_eeprom(cp->regs, 0, 8) == 0x8129 ? 8 : 6;
+
+ if (eeprom->offset & 1) {
+ val = read_eeprom(cp->regs, offset, addr_len) & 0xff;
+ val |= (u16)data[i++] << 8;
+ write_eeprom(cp->regs, offset, val, addr_len);
+ offset++;
+ }
+
+ while (i < len - 1) {
+ val = (u16)data[i++];
+ val |= (u16)data[i++] << 8;
+ write_eeprom(cp->regs, offset, val, addr_len);
+ offset++;
+ }
+
+ if (i < len) {
+ val = read_eeprom(cp->regs, offset, addr_len) & 0xff00;
+ val |= (u16)data[i];
+ write_eeprom(cp->regs, offset, val, addr_len);
+ }
+
+ spin_unlock_irq(&cp->lock);
+ return 0;
+}
+
/* Put the board into D3cold state and wait for WakeUp signal */
static void cp_set_d3_state (struct cp_private *cp)
{
reply other threads:[~2006-06-14 6:43 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=448FAFFC.7070006@snapgear.com \
--to=philipc@snapgear.com \
--cc=jgarzik@pobox.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.