From: Lutz Urban <lurban@lurban.de>
To: netdev@vger.kernel.org
Cc: hadi@cyberus.ca
Subject: Re: pci=routeirq solves EHCI-problem
Date: Tue, 08 Aug 2006 16:27:41 +0200 [thread overview]
Message-ID: <44D89F5D.2000106@lurban.de> (raw)
In-Reply-To: <44D83CB6.7030406@lurban.de>
Hello,
I'm sorry to tell you that my previous message was bogus. The problem
still persists.
Sorry to have bothered you.
Regards,
Lutz Urban
Lutz Urban schrieb:
> Hello,
>
> I got your email-addresses from my /var/log/boot.msg.
>
> The kernel switch 'pci=routeirq' solved the following problem:
>
> Setup:
> - VIA KT880 mainboard with a Geode-CPU
> - SUSE Linux 10.0, kernel 2.6.13-15-default
> - USB-mass storage device (2.5' Samsung disk, chipset can presumably be
> identified if needed)
>
> Booting WITHOUT 'pci=routeirq':
> - When the USB-disk had been connected BEFORE booting, the device would
> freeze upon loading ehci-hcd and usb-storage. usb-storage would be
> unable to read the partion table.
> - After physically disconnecting and reconnecting the device everything
> would be fine.
> - This problem would not occur with uhci-hcd instead of ehci-hcd.
>
> Booting WITH 'pci=routeirq':
> - Everything works fine also when the USB-disk was connected BEFORE boot.
>
> I enclose the output of 'lspci -bvv' (booted with 'pci=routeirq') as a
> text file. If you want further info, I'm very willing to help. (I have
> benefitted a lot from the work of the Open Source Community and given
> very little back)
>
> Kind regards,
> Lutz Urban, Germany
>
> phone: +49-208-4459550
>
>
>
> ------------------------------------------------------------------------
>
> 00:00.0 Host bridge: VIA Technologies, Inc. KT880 Host Bridge
> Subsystem: VIA Technologies, Inc. KT880 Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 8
> Region 0: Memory at e0000000 (32-bit, prefetchable)
> Capabilities: [80] AGP version 3.5
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:00.1 Host bridge: VIA Technologies, Inc. KT880 Host Bridge
> Subsystem: VIA Technologies, Inc. KT880 Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:00.2 Host bridge: VIA Technologies, Inc. KT880 Host Bridge
> Subsystem: VIA Technologies, Inc. KT880 Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:00.3 Host bridge: VIA Technologies, Inc. KT880 Host Bridge
> Subsystem: VIA Technologies, Inc. KT880 Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:00.4 Host bridge: VIA Technologies, Inc. KT880 Host Bridge
> Subsystem: VIA Technologies, Inc. KT880 Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:00.7 Host bridge: VIA Technologies, Inc. KT880 Host Bridge
> Subsystem: VIA Technologies, Inc. KT880 Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> Memory behind bridge: fca00000-feafffff
> Prefetchable memory behind bridge: bff00000-cfefffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [70] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:06.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz] (rev 02)
> Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH FRITZ!Card ISDN Controller
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at febffc00 (32-bit, non-prefetchable)
> Region 1: I/O ports at ec00
>
> 00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> Subsystem: Compex FN22-3(A) LinxPRO Ethernet Adapter
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at e800
> Region 1: Memory at febff800 (32-bit, non-prefetchable)
> Expansion ROM at febe0000 [disabled]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0b.0 Ethernet controller: VIA Technologies, Inc. VT6120/VT6121/VT6122 Gigabit Ethernet Adapter (rev 11)
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (750ns min, 2000ns max), Cache Line Size 08
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at e400
> Region 1: Memory at febff400 (32-bit, non-prefetchable)
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin B routed to IRQ 10
> Region 0: I/O ports at e000
> Region 1: I/O ports at dc00
> Region 2: I/O ports at d800
> Region 3: I/O ports at d400
> Region 4: I/O ports at d000
> Region 5: I/O ports at c800
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
> Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 10
> Region 4: I/O ports at fc00
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at bc00
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at c000
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin B routed to IRQ 10
> Region 4: I/O ports at c400
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin B routed to IRQ 10
> Region 4: I/O ports at cc00
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
> Subsystem: Micro-Star International Co., Ltd.: Unknown device 0470
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 10
> Interrupt: pin C routed to IRQ 10
> Region 0: Memory at febff000 (32-bit, non-prefetchable)
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
> Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at fd000000 (32-bit, non-prefetchable)
> Region 1: Memory at c0000000 (32-bit, prefetchable)
> Expansion ROM at feaf0000 [disabled]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
next prev parent reply other threads:[~2006-08-08 14:27 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-08-08 7:26 pci=routeirq solves EHCI-problem Lutz Urban
2006-08-08 14:27 ` Lutz Urban [this message]
2006-08-12 17:28 ` Chris Wedgwood
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=44D89F5D.2000106@lurban.de \
--to=lurban@lurban.de \
--cc=hadi@cyberus.ca \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.