[U-Boot] [PATCH 08/13] ehci-mxc: Make EHCI power/oc polarities configurable

["Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>]

Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.

Signed-off-by: Beno?t Th?baudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
---
 .../drivers/usb/host/ehci-mx5.c                    |   51 ++++++++++++++++++++
 .../include/usb/ehci-fsl.h                         |   10 ++--
 2 files changed, 57 insertions(+), 4 deletions(-)

diff --git u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c
index 7da1398..52aeae5 100644
--- u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c
+++ u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c
@@ -44,24 +44,33 @@
 /* USB_CTRL */
 #define MXC_OTG_UCTRL_OWIE_BIT		(1 << 27)	/* OTG wakeup intr enable */
 #define MXC_OTG_UCTRL_OPM_BIT		(1 << 24)	/* OTG power mask */
+#define MXC_OTG_UCTRL_O_PWR_POL_BIT	(1 << 24)	/* OTG power pin polarity */
 #define MXC_H1_UCTRL_H1UIE_BIT		(1 << 12)	/* Host1 ULPI interrupt enable */
 #define MXC_H1_UCTRL_H1WIE_BIT		(1 << 11)	/* HOST1 wakeup intr enable */
 #define MXC_H1_UCTRL_H1PM_BIT		(1 << 8)	/* HOST1 power mask */
+#define MXC_H1_UCTRL_H1_PWR_POL_BIT	(1 << 8)	/* HOST1 power pin polarity */
 
 /* USB_PHY_CTRL_FUNC */
+#define MXC_OTG_PHYCTRL_OC_POL_BIT	(1 << 9)	/* OTG Polarity of Overcurrent */
 #define MXC_OTG_PHYCTRL_OC_DIS_BIT	(1 << 8)	/* OTG Disable Overcurrent Event */
+#define MXC_H1_OC_POL_BIT		(1 << 6)	/* UH1 Polarity of Overcurrent */
 #define MXC_H1_OC_DIS_BIT		(1 << 5)	/* UH1 Disable Overcurrent Event */
+#define MXC_OTG_PHYCTRL_PWR_POL_BIT	(1 << 3)	/* OTG Power Pin Polarity */
 
 /* USBH2CTRL */
+#define MXC_H2_UCTRL_H2_OC_POL_BIT	(1 << 31)
 #define MXC_H2_UCTRL_H2_OC_DIS_BIT	(1 << 30)
 #define MXC_H2_UCTRL_H2UIE_BIT		(1 << 8)
 #define MXC_H2_UCTRL_H2WIE_BIT		(1 << 7)
 #define MXC_H2_UCTRL_H2PM_BIT		(1 << 4)
+#define MXC_H2_UCTRL_H2_PWR_POL_BIT	(1 << 4)
 
 /* USBH3CTRL */
+#define MXC_H3_UCTRL_H3_OC_POL_BIT	(1 << 31)
 #define MXC_H3_UCTRL_H3_OC_DIS_BIT	(1 << 30)
 #define MXC_H3_UCTRL_H3UIE_BIT		(1 << 8)
 #define MXC_H3_UCTRL_H3WIE_BIT		(1 << 7)
+#define MXC_H3_UCTRL_H3_PWR_POL_BIT	(1 << 4)
 
 /* USB_CTRL_1 */
 #define MXC_USB_CTRL_UH1_EXT_CLK_EN	(1 << 25)
@@ -151,12 +160,22 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
 		if (flags & MXC_EHCI_INTERNAL_PHY) {
 			v = __raw_readl(usbother_base +
 					MXC_USB_PHY_CTR_FUNC_OFFSET);
+			if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+				v |= MXC_OTG_PHYCTRL_OC_POL_BIT;
+			else
+				v &= ~MXC_OTG_PHYCTRL_OC_POL_BIT;
 			if (flags & MXC_EHCI_POWER_PINS_ENABLED)
 				/* OC/USBPWR is used */
 				v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT;
 			else
 				/* OC/USBPWR is not used */
 				v |= MXC_OTG_PHYCTRL_OC_DIS_BIT;
+#ifdef CONFIG_MX51
+			if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+				v |= MXC_OTG_PHYCTRL_PWR_POL_BIT;
+			else
+				v &= ~MXC_OTG_PHYCTRL_PWR_POL_BIT;
+#endif
 			__raw_writel(v, usbother_base +
 					MXC_USB_PHY_CTR_FUNC_OFFSET);
 
@@ -167,6 +186,12 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
 			else
 				v |= MXC_OTG_UCTRL_OPM_BIT;
 #endif
+#ifdef CONFIG_MX53
+			if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+				v |= MXC_OTG_UCTRL_O_PWR_POL_BIT;
+			else
+				v &= ~MXC_OTG_UCTRL_O_PWR_POL_BIT;
+#endif
 			__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
 		}
 		break;
@@ -186,9 +211,19 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
 		else
 			v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used */
 #endif
+#ifdef CONFIG_MX53
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MXC_H1_UCTRL_H1_PWR_POL_BIT;
+		else
+			v &= ~MXC_H1_UCTRL_H1_PWR_POL_BIT;
+#endif
 		__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
 
 		v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+		if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+			v |= MXC_H1_OC_POL_BIT;
+		else
+			v &= ~MXC_H1_OC_POL_BIT;
 		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
 			v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
 		else
@@ -205,10 +240,18 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
 			v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */
 #endif
 #ifdef CONFIG_MX53
+		if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+			v |= MXC_H2_UCTRL_H2_OC_POL_BIT;
+		else
+			v &= ~MXC_H2_UCTRL_H2_OC_POL_BIT;
 		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
 			v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */
 		else
 			v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MXC_H2_UCTRL_H2_PWR_POL_BIT;
+		else
+			v &= ~MXC_H2_UCTRL_H2_PWR_POL_BIT;
 #endif
 
 		__raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET);
@@ -216,10 +259,18 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
 #ifdef CONFIG_MX53
 	case 3: /* Host 3 ULPI */
 		v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET);
+		if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+			v |= MXC_H3_UCTRL_H3_OC_POL_BIT;
+		else
+			v &= ~MXC_H3_UCTRL_H3_OC_POL_BIT;
 		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
 			v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */
 		else
 			v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MXC_H3_UCTRL_H3_PWR_POL_BIT;
+		else
+			v &= ~MXC_H3_UCTRL_H3_PWR_POL_BIT;
 
 		__raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET);
 		break;
diff --git u-boot-usb-76454b2.orig/include/usb/ehci-fsl.h u-boot-usb-76454b2/include/usb/ehci-fsl.h
index 4dee5b0..a1438d6 100644
--- u-boot-usb-76454b2.orig/include/usb/ehci-fsl.h
+++ u-boot-usb-76454b2/include/usb/ehci-fsl.h
@@ -266,11 +266,13 @@ struct usb_ehci {
 #define MXC_EHCI_INTERFACE_MASK		(0xf)
 
 #define MXC_EHCI_POWER_PINS_ENABLED	(1 << 5)
-#define MXC_EHCI_TTL_ENABLED		(1 << 6)
+#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH	(1 << 6)
+#define MXC_EHCI_OC_PIN_ACTIVE_LOW	(1 << 7)
+#define MXC_EHCI_TTL_ENABLED		(1 << 8)
 
-#define MXC_EHCI_INTERNAL_PHY		(1 << 7)
-#define MXC_EHCI_IPPUE_DOWN		(1 << 8)
-#define MXC_EHCI_IPPUE_UP		(1 << 9)
+#define MXC_EHCI_INTERNAL_PHY		(1 << 9)
+#define MXC_EHCI_IPPUE_DOWN		(1 << 10)
+#define MXC_EHCI_IPPUE_UP		(1 << 11)
 
 /* Board-specific initialization */
 int board_ehci_hcd_init(int port);