From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Jacopo Mondi <jacopo@jmondi.org>
Cc: geert+renesas@glider.be, magnus.damm@gmail.com,
linus.walleij@linaro.org, linux-renesas-soc@vger.kernel.org,
linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH] pinctrl: sh-pfc: r8a7791: Add ADI pinconf support
Date: Tue, 29 Nov 2016 21:30:56 +0200 [thread overview]
Message-ID: <4558124.JutbKSQ7ug@avalon> (raw)
In-Reply-To: <1480410716-25993-1-git-send-email-jacopo@jmondi.org>
Hi Jacopo,
Thank you for the patch.
On Tuesday 29 Nov 2016 10:11:56 Jacopo Mondi wrote:
> Add pin configuration support for Gyro-ADC, named ADI on r8a7791 SoC.
>
> The Gyro-ADC supports three different configurations:
> a single ADC (adi and adi_b groups), 2 ADCs selectable through a single
> channel select signal (adi_chsel1 and adi_chsel1_b groups),
I've only briefly looked up at the datasheet, but is that a supported mode ?
It seems that mode 1 uses 4 channels and mode 2 and 3 use 8 channels.
> up to 4 ADCs
> through 2 channel select signals (adi_chsel2 and adi_chsel2_b groups)
> and up to 8 ADCs through 3 channel select signals (adi_chsel3 and
> adi_chsel3_b groups)
>
> Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
> ---
>
> Compiled only, not tested with an actual ADC.
>
> For reference only, these are the changes introduced by Geert's private
> review of first sketch of this patch:
> * separate ADI chsel in 3 overlapping groups:
> the user can now select how many pins to assign to channel selection
> function.
>
> ---
> drivers/pinctrl/sh-pfc/pfc-r8a7791.c | 86 +++++++++++++++++++++++++++++++++
> 1 file changed, 86 insertions(+)
>
> diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
> b/drivers/pinctrl/sh-pfc/pfc-r8a7791.c index 7ca37c3..3898747 100644
> --- a/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
> +++ b/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
> @@ -1691,6 +1691,72 @@ static const struct sh_pfc_pin pinmux_pins[] = {
> PINMUX_GPIO_GP_ALL(),
> };
>
> +/* - ADI --------------------------------------------------------------- */
> +static const unsigned int adi_pins[] = {
> + /* ADIDATA, ADICS, CLK*/
Missing space before */. Same comment in other places below.
> + RCAR_GP_PIN(6, 24), RCAR_GP_PIN(6, 25), RCAR_GP_PIN(6, 26),
> +};
> +static const unsigned int adi_mux[] = {
> + /* ADIDATA, ADICS, CLK*/
> + ADIDATA_MARK, ADICS_SAMP_MARK, ADICLK_MARK,
> +};
> +static const unsigned int adi_chsel1_pins[] = {
> + /* CHS 0 */
> + RCAR_GP_PIN(6, 27),
> +};
> +static const unsigned int adi_chsel1_mux[] = {
> + /* CHS 0 */
> + ADICHS0_MARK, ADICHS1_MARK, ADICHS2_MARK,
One pin, three mux ?
> +};
> +static const unsigned int adi_chsel2_pins[] = {
> + /* CHS 0, 1 */
> + RCAR_GP_PIN(6, 27), RCAR_GP_PIN(6, 28),
> +};
> +static const unsigned int adi_chsel2_mux[] = {
> + /* CHS 0, 1 */
> + ADICHS0_MARK, ADICHS1_MARK, ADICHS2_MARK,
Two pins, three mux ?
> +};
> +static const unsigned int adi_chsel3_pins[] = {
> + /* CHS 0, 1, 2 */
> + RCAR_GP_PIN(6, 27), RCAR_GP_PIN(6, 28), RCAR_GP_PIN(6, 29),
> +};
> +static const unsigned int adi_chsel3_mux[] = {
> + /* CHS 0, 1, 2 */
> + ADICHS0_MARK, ADICHS1_MARK, ADICHS2_MARK,
> +};
> +static const unsigned int adi_b_pins[] = {
> + /* ADIDATA B, ADICS B, CLK B */
> + RCAR_GP_PIN(5, 25), RCAR_GP_PIN(5, 26), RCAR_GP_PIN(5, 27),
> +};
> +static const unsigned int adi_b_mux[] = {
> + /* ADIDATA B, ADICS B, CLK B */
> + ADIDATA_B_MARK, ADICS_SAMP_B_MARK, ADICLK_B_MARK,
> +};
> +static const unsigned int adi_chsel1_b_pins[] = {
> + /* CHS B 0 */
> + RCAR_GP_PIN(5, 28),
> +};
> +static const unsigned int adi_chsel1_b_mux[] = {
> + /* CHS B 0 */
> + ADICHS0_B_MARK,
> +};
> +static const unsigned int adi_chsel2_b_pins[] = {
> + /* CHS B 0, 1 */
> + RCAR_GP_PIN(5, 28), RCAR_GP_PIN(5, 29),
> +};
> +static const unsigned int adi_chsel2_b_mux[] = {
> + /* CHS B 0, 1 */
> + ADICHS0_B_MARK, ADICHS1_B_MARK,
> +};
> +static const unsigned int adi_chsel3_b_pins[] = {
> + /* CHS B 0, 1, 2 */
> + RCAR_GP_PIN(5, 28), RCAR_GP_PIN(5, 29), RCAR_GP_PIN(5, 30),
> +};
> +static const unsigned int adi_chsel3_b_mux[] = {
> + /* CHS B 0, 1, 2 */
> + ADICHS0_B_MARK, ADICHS1_B_MARK, ADICHS2_B_MARK,
> +};
> +
> /* - Audio Clock ------------------------------------------------------- */
> static const unsigned int audio_clk_a_pins[] = {
> /* CLK */
> @@ -4343,6 +4409,14 @@ static const unsigned int vin2_clk_mux[] = {
> };
>
> static const struct sh_pfc_pin_group pinmux_groups[] = {
> + SH_PFC_PIN_GROUP(adi),
> + SH_PFC_PIN_GROUP(adi_chsel1),
> + SH_PFC_PIN_GROUP(adi_chsel2),
> + SH_PFC_PIN_GROUP(adi_chsel3),
> + SH_PFC_PIN_GROUP(adi_b),
> + SH_PFC_PIN_GROUP(adi_chsel1_b),
> + SH_PFC_PIN_GROUP(adi_chsel2_b),
> + SH_PFC_PIN_GROUP(adi_chsel3_b),
> SH_PFC_PIN_GROUP(audio_clk_a),
> SH_PFC_PIN_GROUP(audio_clk_b),
> SH_PFC_PIN_GROUP(audio_clk_b_b),
> @@ -4687,6 +4761,17 @@ static const struct sh_pfc_pin_group pinmux_groups[]
> = { SH_PFC_PIN_GROUP(vin2_clk),
> };
>
> +static const char * const adi_groups[] = {
> + "adi",
> + "adi_chsel1",
> + "adi_chsel2",
> + "adi_chsel3",
> + "adi_b",
> + "adi_chsel1_b",
> + "adi_chsel2_b",
> + "adi_chsel3_b",
> +};
> +
> static const char * const audio_clk_groups[] = {
> "audio_clk_a",
> "audio_clk_b",
> @@ -5192,6 +5277,7 @@ static const char * const vin2_groups[] = {
> };
>
> static const struct sh_pfc_function pinmux_functions[] = {
> + SH_PFC_FUNCTION(adi),
> SH_PFC_FUNCTION(audio_clk),
> SH_PFC_FUNCTION(avb),
> SH_PFC_FUNCTION(can0),
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2016-11-29 19:30 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-29 9:11 [PATCH] pinctrl: sh-pfc: r8a7791: Add ADI pinconf support Jacopo Mondi
2016-11-29 19:30 ` Laurent Pinchart [this message]
2016-11-29 21:39 ` Geert Uytterhoeven
2016-11-30 13:49 ` Geert Uytterhoeven
2016-12-01 16:40 ` jacopo
2016-12-01 8:47 ` Geert Uytterhoeven
2016-12-01 22:10 ` [PATCH v2] " Jacopo Mondi
2016-12-01 22:14 ` [PATCH v3] " Jacopo Mondi
2016-12-09 9:03 ` Geert Uytterhoeven
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4558124.JutbKSQ7ug@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=geert+renesas@glider.be \
--cc=jacopo@jmondi.org \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=magnus.damm@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.