From: Ed Sweetman <safemode2@comcast.net>
To: Gene Heskett <gene.heskett@verizon.net>
Cc: linux-kernel@vger.kernel.org, linux-usb-devel@lists.sourceforge.net
Subject: Re: 2.6.19-rc5-mm2 : usb keeps resetting usb keyboard.
Date: Sat, 25 Nov 2006 08:21:36 -0500 [thread overview]
Message-ID: <45684360.1060801@comcast.net> (raw)
In-Reply-To: <200611242321.02776.gene.heskett@verizon.net>
Gene Heskett wrote:
> On Friday 24 November 2006 22:41, Ed Sweetman wrote:
>
>> I just upgraded from a ps2 keyboard to usb and have been getting these
>> messages seemingly randomly, which also corresponds to whatever key i'm
>> pressing at the time they occur to act like it's stuck down.
>>
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>> usb 2-2: reset low speed USB device using ohci_hcd and address 3
>>
>> (repeated a few hundred times )
>>
>>
> All the data below doesn't point to the culprit.
>
> I also have this, and I'd bet the common point is going to be an M$
> wireless mouse like I have. The mouse works ok as near as I can tell, so
> I'm not sure of the exact cause.
>
> To verify, unplug the receiver for that mouse, wait 5secs, and plug it
> back in, which if thats it should move the mouse, and the log message to
> a higher number on the usb tree.
>
> Also, FWIW dear lkml readers, my logs have been contaminated with this
> since about a year ago, running kernel.org kernels on an FC2 system, but
> using the latest FC6 non-xen kernel.
>
I dont have a wireless usb mouse or any hardware from microsoft
running. My usb mouse is a standard logitech that i've been using for a
couple years. I haven't had these errors in my log before installing
my usb keyboard.
These are the only usb devices in the system.
below is my lsusb -v. For what it's worth.
Bus 002 Device 003: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x046d Logitech, Inc.
idProduct 0xc00c Optical Wheel Mouse
bcdDevice 6.10
iManufacturer 1 Logitech
iProduct 2 USB Mouse
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 68
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 002: ID 1267:0103 Logic3 / SpectraVideo plc
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1267 Logic3 / SpectraVideo plc
idProduct 0x0103
bcdDevice 1.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 54
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 52
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0003 1x 3 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.19-rc5-mm2 ohci_hcd
iProduct 2 OHCI Host Controller
iSerial 1 0000:00:02.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 10
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0303 lowspeed power enable connect
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Port 9: 0000.0100 power
Port 10: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.19-rc5-mm2 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:02.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 10
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0000
Port 2: 0000.0000
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Port 9: 0000.0100 power
Port 10: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
> >From an lsusb -v:
> ----------
> Bus 002 Device 003: ID 045e:008c Microsoft Corp. Wireless Intellimouse
> Explorer 2.0
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 8
> idVendor 0x045e Microsoft Corp.
> idProduct 0x008c Wireless Intellimouse Explorer 2.0
> bcdDevice 0.57
> iManufacturer 1 Microsoft
> iProduct 2 Microsoft Wireless Optical Mouse 1.0A
> iSerial 0
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 34
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0xa0
> Remote Wakeup
> MaxPower 50mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 1
> bInterfaceClass 3 Human Interface Devices
> bInterfaceSubClass 1 Boot Interface Subclass
> bInterfaceProtocol 2 Mouse
> iInterface 0
> HID Device Descriptor:
> bLength 9
> bDescriptorType 33
> bcdHID 1.11
> bCountryCode 0 Not supported
> bNumDescriptors 1
> bDescriptorType 34 Report
> wDescriptorLength 209
> Report Descriptors:
> ** UNAVAILABLE **
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 3
> Transfer Type Interrupt
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0008 1x 8 bytes
> bInterval 10
> -------------------
>
> How close am I in this suposition?
>
>
next prev parent reply other threads:[~2006-11-25 13:21 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-25 3:41 2.6.19-rc5-mm2 : usb keeps resetting usb keyboard Ed Sweetman
2006-11-25 4:21 ` Gene Heskett
2006-11-25 13:21 ` Ed Sweetman [this message]
2006-11-25 16:49 ` [linux-usb-devel] " Alan Stern
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45684360.1060801@comcast.net \
--to=safemode2@comcast.net \
--cc=gene.heskett@verizon.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.