From: Jay Cliburn <jacliburn@bellsouth.net>
To: Jose Alberto Reguero <jareguero@telefonica.net>
Cc: linux-kernel@vger.kernel.org
Subject: Re: [PATCH] Add suport for Marvell 88SE6121 in pata_marvell
Date: Mon, 15 Jan 2007 13:00:20 -0600 [thread overview]
Message-ID: <45ABCF44.3080101@bellsouth.net> (raw)
In-Reply-To: <200701061324.47993.jareguero@telefonica.net>
Jose Alberto Reguero wrote:
> Marvell 88SE6121
[snip]
> ------------------------------------------------------------------------
>
> --- linux-2.6.20-rc3/drivers/ata/pata_marvell.c 2007-01-01 01:53:20.000000000 +0100
> +++ linux-2.6.20-rc3.new/drivers/ata/pata_marvell.c 2007-01-06 12:33:03.000000000 +0100
> @@ -49,7 +49,7 @@
[snip]
Works-for-me: Jay Cliburn <jacliburn@bellsouth.net>
The following dmesg snippet after applying the patch shows life from the
hitherto unsupported device: (I connected an unpartitioned SATA HDD to it.)
==============
[ 39.789326] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 39.789436] ata3: PATA max UDMA/100 cmd 0xEC00 ctl 0xE882 bmdma
0xE400 irq 28
[ 39.789541] ata4: PATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma
0xE408 irq 28
[ 39.789559] scsi2 : pata_marvell
[ 39.790121] BAR5:00:02 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00
08:00 09:00 0A:00 0B:00 0C:07 0D:00 0E:00 0F:00
[ 39.790152] ata3: port disabled. ignoring.
[ 39.790154] ata3: reset failed, giving up
[ 39.790161] scsi3 : pata_marvell
[ 39.790589] BAR5:00:02 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00
08:00 09:00 0A:00 0B:00 0C:07 0D:00 0E:00 0F:00
[ 39.958055] ATA: abnormal status 0x7F on port 0xE807
[ 39.968869] ATA: abnormal status 0x7F on port 0xE807
[ 39.979450] ata4.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48
[ 39.979453] ata4.00: ata4: dev 0 multi count 16
[ 39.987443] ata4.00: configured for UDMA/133
[ 39.987628] scsi 3:0:0:0: Direct-Access ATA WDC WD2500KS-00M
02.0 PQ: 0 ANSI: 5
[ 39.988524] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
[ 39.988546] sdb: Write Protect is off
[ 39.988548] sdb: Mode Sense: 00 3a 00 00
[ 39.988583] SCSI device sdb: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 39.988695] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
[ 39.988713] sdb: Write Protect is off
[ 39.988715] sdb: Mode Sense: 00 3a 00 00
[ 39.988749] SCSI device sdb: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 39.988781] sdb: unknown partition table
[ 39.994867] sd 3:0:0:0: Attached scsi disk sdb
[ 39.994990] sd 3:0:0:0: Attached scsi generic sg1 type 0
This is the relevant portion of lspci:
==============
06:00.0 SATA controller: Marvell Technology Group Ltd. Unknown device
6121 (rev b0) (prog-if 8f)
Subsystem: ASUSTeK Computer Inc. Unknown device 8212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: Memory at fbeffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable
-
Address: 00000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 21 61 07 01 10 00 b0 8f 06 01 10 00 00 00
10: 01 ec 00 00 81 e8 00 00 01 e8 00 00 81 e4 00 00
20: 01 e4 00 00 00 fc ef fb 00 00 00 00 43 10 12 82
30: 00 00 00 00 48 00 00 00 00 00 00 00 0b 01 00 00
40: 24 c9 c0 00 1f 80 00 00 01 50 02 5a 00 20 00 13
50: 05 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 58 c4 21 40 b0 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 10 00 11 00 c0 0f 18 00 00 24 08 00 11 a4 03 01
f0: 00 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
prev parent reply other threads:[~2007-01-15 19:00 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-01-06 12:24 [PATCH] Add suport for Marvell 88SE6121 in pata_marvell Jose Alberto Reguero
2007-01-06 15:36 ` Jose Alberto Reguero
2007-01-15 19:00 ` Jay Cliburn [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45ABCF44.3080101@bellsouth.net \
--to=jacliburn@bellsouth.net \
--cc=jareguero@telefonica.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.