From: Stefan Priebe - FH <studium@profihost.com>
To: linux-kernel@vger.kernel.org
Subject: SATA ahci Bug in 2.6.19.x
Date: Mon, 22 Jan 2007 09:02:40 +0100 [thread overview]
Message-ID: <45B46FA0.2060901@profihost.com> (raw)
Hello!
I've an Asus A8V Mainboard which works wonderful with a 2.6.18.X kernel.
But i cannot use the SATA Controller with a 2.6.19.x Kernel.
dmesg output from 2.6.18.3 where it works perfectly:
libata version 2.00 loaded.
ahci 0000:00:0f.0: version 2.0
GSI 19 sharing vector 0xD9 and IRQ 19
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI
21 (level, low) -> IRQ 217
ahci 0000:00:0f.0: AHCI 0001.0000 32 slots 4
ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:0f.0: flags: 64bit ncq pm led
clo pmp pio slum part
ata1: SATA max UDMA/133 cmd
0xFFFFC20000004D00 ctl 0x0 bmdma 0x0 irq 225
ata2: SATA max UDMA/133 cmd
0xFFFFC20000004D80 ctl 0x0 bmdma 0x0 irq 225
ata3: SATA max UDMA/133 cmd
0xFFFFC20000004E00 ctl 0x0 bmdma 0x0 irq 225
ata4: SATA max UDMA/133 cmd
0xFFFFC20000004E80 ctl 0x0 bmdma 0x0 irq 225
scsi0 : ahci
ata1: SATA link up 3.0 Gbps (SStatus 123
SControl 300)
ata1.00: ATA-7, max UDMA7, 312581808
sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123
SControl 300)
ata2.00: ATA-7, max UDMA7, 312581808
sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
ata4: SATA link down (SStatus 0 SControl 300)
Vendor: ATA Model: SAMSUNG HD160JJ
Rev: ZM10
Type: Direct-Access
ANSI SCSI revision: 05
Vendor: ATA Model: SAMSUNG HD160JJ
Rev: ZM10
Type: Direct-Access
ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr
sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr
sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 312581808 512-byte hdwr
sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr
sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 < sdb5 sdb6 sdb7 >
sd 1:0:0:0: Attached scsi disk sdb
Output with 2.6.19.2 (logged via netconsole cause the system can't boot):
"ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 21"
"ahci 0000:00:0f.0: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE
mode"
"ahci 0000:00:0f.0: flags: 64bit ncq pm led clo pmp pio slum part "
"ata1: SATA max UDMA/133 cmd 0xFFFFC20000004D00 ctl 0x0 bmdma 0x0 irq 1277"
"ata2: SATA max UDMA/133 cmd 0xFFFFC20000004D80 ctl 0x0 bmdma 0x0 irq 1277"
"ata3: SATA max UDMA/133 cmd 0xFFFFC20000004E00 ctl 0x0 bmdma 0x0 irq 1277"
"ata4: SATA max UDMA/133 cmd 0xFFFFC20000004E80 ctl 0x0 bmdma 0x0 irq 1277"
"scsi0 : ahci"
"ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)"
"ata1.00: qc timeout (cmd 0xec)"
"ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104)"
"ata1: port is slow to respond, please be patient (Status 0x80)"
"ata1: port failed to respond (30 secs, Status 0x80)"
"ata1: COMRESET failed (device not ready)"
"ata1: hardreset failed, retrying in 5 secs"
"ata1: port is slow to respond, please be patient (Status 0x80)"
"ata1: port failed to respond (30 secs, Status 0x80)"
"ata1: COMRESET failed (device not ready)"
"ata1: hardreset failed, retrying in 5 secs"
"ata1: port is slow to respond, please be patient (Status 0x80)"
"ata1: port failed to respond (30 secs, Status 0x80)"
"ata1: COMRESET failed (device not ready)"
"ata1: reset failed, giving up"
"scsi1 : ahci"
"ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)"
"ata2.00: qc timeout (cmd 0xec)"
"ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)"
"ata2: port is slow to respond, please be patient (Status 0x80)"
"ata2: port failed to respond (30 secs, Status 0x80)"
"ata2: COMRESET failed (device not ready)"
"ata2: hardreset failed, retrying in 5 secs"
"ata2: port is slow to respond, please be patient (Status 0x80)"
"ata2: port failed to respond (30 secs, Status 0x80)"
"ata2: COMRESET failed (device not ready)"
"ata2: hardreset failed, retrying in 5 secs"
"ata2: port is slow to respond, please be patient (Status 0x80)"
"ata2: port failed to respond (30 secs, Status 0x80)"
"ata2: COMRESET failed (device not ready)"
"ata2: reset failed, giving up"
"scsi2 : ahci"
"ata3: SATA link down (SStatus 0 SControl 300)"
"scsi3 : ahci"
"ata4: SATA link down (SStatus 0 SControl 300)"
Stefan
next reply other threads:[~2007-01-22 8:02 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-01-22 8:02 Stefan Priebe - FH [this message]
2007-01-22 14:00 ` SATA ahci Bug in 2.6.19.x Stephen Evanchik
2007-01-25 21:24 ` Stefan Priebe - FH
2007-01-26 3:25 ` Luming Yu
2007-01-26 4:46 ` Stephen Evanchik
2007-01-26 5:22 ` Luming Yu
2007-01-26 6:18 ` Stephen Evanchik
2007-01-26 10:33 ` Alan
2007-01-26 9:19 ` Stefan Priebe - FH
2007-01-30 10:44 ` Stefan Priebe - FH
[not found] <7G2pJ-2iX-23@gated-at.bofh.it>
[not found] ` <7G828-3zn-3@gated-at.bofh.it>
[not found] ` <7HpWX-3D2-5@gated-at.bofh.it>
[not found] ` <7Hrci-5ou-5@gated-at.bofh.it>
[not found] ` <7HrP4-6t8-1@gated-at.bofh.it>
[not found] ` <7Hvzs-3Tj-23@gated-at.bofh.it>
[not found] ` <7IYJ1-281-27@gated-at.bofh.it>
2007-02-14 8:57 ` Manuel Metz
2007-02-21 11:55 ` Tejun Heo
2007-02-21 16:46 ` Manuel Metz
2007-02-24 6:25 ` Tejun Heo
2007-02-24 7:55 ` Jeff Garzik
2007-02-26 8:32 ` Manuel Metz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45B46FA0.2060901@profihost.com \
--to=studium@profihost.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.