From: Stephen Clark <Stephen.Clark@seclark.us>
To: linux-ide@vger.kernel.org
Subject: CD problems booting FC7 RC3
Date: Mon, 02 Apr 2007 15:58:19 -0400 [thread overview]
Message-ID: <4611605B.6060601@seclark.us> (raw)
Hi,
When trying to boot FC7 RC3 on my HP N5430 laptop I get the following:
...
Write protecting the kernel read-only data: 845k
input: PS/2 Generic Mouse as /class/input/input2
SCSI subsystem initialized
libata version 2.20 loaded.
ACPI: Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011000
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011008
irq 15
scsi0 : pata_ali
PM: Adding info for No Bus:host0
ata1.00: ATA-5: HITACHI_DK23CA-20, 00H1A0A3, max UDMA/100
ata1.00: 39070080 sectors, multi 16: LBA
ata1.00: configured for UDMA/33
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
powernow: SGTC: 10000
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
powernow: SGTC: 10000
powernow: Minimum speed 300 MHz. Maximum speed 850 MHz.
powernow-k8: Processor cpuid 670 not supported
Using IPI No-Shortcut mode
Magic number: 3:342:541
Freeing unused kernel memory: 248k freed
Write protecting the kernel read-only data: 845k
input: PS/2 Generic Mouse as /class/input/input2
SCSI subsystem initialized
libata version 2.20 loaded.
ACPI: Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011000
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011008
irq 15
scsi0 : pata_ali
PM: Adding info for No Bus:host0
ata1.00: ATA-5: HITACHI_DK23CA-20, 00H1A0A3, max UDMA/100
ata1.00: 39070080 sectors, multi 16: LBA
ata1.00: configured for UDMA/33
scsi1 : pata_ali
PM: Adding info for No Bus:host1
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
PM: Adding info for No Bus:target0:0:0
scsi 0:0:0:0: Direct-Access ATA HITACHI_DK23CA-2 00H1 PQ: 0 ANSI: 5
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:target1:0:0
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata2: soft resetting port
ATA: abnormal status 0xD0 on port 0x00010177
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata2.00: revalidation failed (errno=-5)
ata2: failed to recover some devices, retrying in 5 secs
ata2: port is slow to respond, please be patient (Status 0xd0)
ata2: port failed to respond (30 secs, Status 0xd0)
ata2: soft resetting port
ATA: abnormal status 0xD0 on port 0x00010177
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata2.00: revalidation failed (errno=-5)
ata2.00: limiting speed to UDMA/33:PIO3
ata2: failed to recover some devices, retrying in 5 secs
ata2: port is slow to respond, please be patient (Status 0xd0)
ata2: port failed to respond (30 secs, Status 0xd0)
ata2: soft resetting port
ATA: abnormal status 0xD0 on port 0x00010177
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata2.00: revalidation failed (errno=-5)
ata2.00: disabled
ata2: EH complete
PM: Removing info for No Bus:target1:0:0
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO
or FUA
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
--------------------------------------
WARNING: Cannot find root file system!
--------------------------------------
Create symlink /dev/root and then exit this shell to continue
the boot sequence.
bash: no job control in this shell
bash-3.2#
(END)
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
next reply other threads:[~2007-04-02 19:58 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-04-02 19:58 Stephen Clark [this message]
2007-04-03 2:40 ` CD problems booting FC7 RC3 Albert Lee
2007-04-03 13:37 ` Stephen Clark
-- strict thread matches above, loose matches on Subject: below --
2007-04-07 2:55 Vlad Codrea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4611605B.6060601@seclark.us \
--to=stephen.clark@seclark.us \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.