All of lore.kernel.org
 help / color / mirror / Atom feed
From: Francis Russell <FrancisRussell@btinternet.com>
To: linux-kernel@vger.kernel.org
Subject: Re: pata_via appears to incorrectly detects 40-pin cable
Date: Fri, 18 May 2007 10:46:43 +0100	[thread overview]
Message-ID: <464D7603.7010308@btinternet.com> (raw)
In-Reply-To: <20070518013955.41df5765@the-village.bc.nu>

[-- Attachment #1: Type: text/plain, Size: 944 bytes --]


> Does the laptop actually have 80 wire cables - did you see UDMA100
> actually being used. If so can you send me an lspci -vxx and a dmesg.
> Probably we need to add it to the list of devices using short 40 wire
> cable tricks

I have been using UDMA5/ATA100 for months, although this was set by a 
hdparm init.d script. Disabling the script, performing a cold reset and 
booting into a 2.6.21 kernel with the old ATA system enabled, hdparm -i 
indicated the HD was using UDMA5. I'm assuming that this means the old 
drivers do not limit to ATA33 unless there is a better I can check this.

I removed the laptop's hard drive. It fits into a cradle which is 
inserted into the laptop. There is no form of cable or adapter that is 
placed on the HD's connector. It just plugs directly into a socket 
inside the laptop when the cradle is inserted.

I hope this is enough information. I've included the output of dmesg and 
lspci -vxx.

Francis


[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 15449 bytes --]

0x342
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2004.618 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1294252k/1309632k available (2072k kernel code, 14224k reserved, 714k data, 196k init, 392128k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffaa000 - 0xfffff000   ( 340 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc03bc000 - 0xc03ed000   ( 196 kB)
      .data : 0xc030618f - 0xc03b8b94   ( 714 kB)
      .text : 0xc0100000 - 0xc030618f   (2072 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4011.25 BogoMIPS (lpj=2005626)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Mobile AMD Athlon 64 Processor 3000+ stepping 00
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd64c, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 8100-810f claimed by vt8235 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *5, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *9, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *5, disabled.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 12 14 15) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.20 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:05: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:05: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:05: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:05: iomem range 0xffee0000-0xffefffff has been reserved
pnp: 00:06: ioport range 0x600-0x60f has been reserved
pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:06: ioport range 0xfe10-0xfe11 has been reserved
pnp: 00:06: ioport range 0xfe00-0xfe00 has been reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
  IO window: 2000-2fff
  MEM window: d0100000-d01fffff
  PREFETCH window: d8000000-dfffffff
PCI: Bus 2, cardbus bridge: 0000:00:07.0
  IO window: 00001c00-00001cff
  IO window: 00003000-000030ff
  PREFETCH window: 60000000-63ffffff
  MEM window: 64000000-67ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x37 set to 0x80
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:01:00.0
vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 5742k, total 131072k
vesafb: mode is 1400x1050x16, linelength=2800, pages=44
vesafb: protected mode interface info at c000:56ac
vesafb: pmi: set display start = c00c571a, set palette = c00c5754
vesafb: pmi: ports = 2010 2016 2054 2038 203c 205c 2000 2004 20b0 20b2 20b4 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 175x65
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.102 (c) Dave Jones
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
tg3.c:v3.76 (May 5, 2007)
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 16
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:c0:9f:67:01:5f
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
pata_via 0000:00:11.1: version 0.3.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011860 irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011868 irq 15
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: ATA-6: HTS721010G9AT00, MCZOA51A, max UDMA/100
ata1.00: 195371568 sectors, multi 16: LBA48 
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: configured for UDMA/33
Switched to high resolution mode on CPU 0
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      HTS721010G9AT00  MCZO PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ-835S  GQM5 PQ: 0 ANSI: 5
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 196k freed
ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 18 (level, low) -> IRQ 17
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]  MMIO=[d0015000-d00157ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input1
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
irda_init()
NET: Registered protocol family 23
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 18, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda caddy
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 18, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 18
usb 1-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 18, io base 0x00001840
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00c09f0000304fb1]
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: configuration #1 chosen from 1 choice
sd 0:0:0:0: Attached scsi generic sg0 type 0
hub 1-1:1.0: USB hub found
sr 1:0:0:0: Attached scsi generic sg1 type 5
hub 1-1:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 18, io mem 0xd0015800
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-1: USB disconnect, address 2
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xe0000000
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 19
ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006
input: SynPS/2 Synaptics TouchPad as /class/input/input2
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
ipw2200: Detected geography ZZE (13 802.11bg channels, 19 802.11a channels)
IrDA: Registered device irda0
nsc-ircc, Found dongle: HP HSDL-1100/HSDL-2100
ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:11.6 to 64
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 4 ports detected
Yenta: CardBus bridge found at 0000:00:07.0 [1025:0057]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:07.0, mfunc 0x007c1b22, devctl 0x44
Yenta: ISA IRQ mask 0x0a70, PCI irq 16
Socket status: 30000086
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Adding 1566328k swap on /dev/sda3.  Priority:-1 extents:1 across:1566328k
EXT3 FS on sda4, internal journal
loop: module loaded
fuse init (API version 7.8)
ACPI: CPU0 (power states: C1[C1] C2[C2])
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
powernow-k8: Found 1 Mobile AMD Athlon 64 Processor 3000+ processors (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x8
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0xc
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0xe
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x17
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access     Generic  Flash R/W        2002 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
ieee80211_crypt: registered algorithm 'TKIP'
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
ACPI: Thermal Zone [THRM] (52 C)
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
PM: Writing back config space on device 0000:00:0b.0 at offset b (was 3ed173b, writing 571025)
PM: Writing back config space on device 0000:00:0b.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:00:0b.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:00:0b.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:00:0b.0 at offset 0 (was 3ed173b, writing 169c14e4)
Clocksource tsc unstable (delta = -72354138 ns)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[drm] Initialized radeon 1.27.0 20060524 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
eth1: no IPv6 routers present


[-- Attachment #3: lspci.txt --]
[-- Type: text/plain, Size: 10276 bytes --]

00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
	Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
	Flags: bus master, 66MHz, medium devsel, latency 8
	Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [80] AGP version 3.5
	Capabilities: [c0] HyperTransport: Slave or Primary Interface
	Capabilities: [68] Power Management version 2
	Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
00: 06 11 88 31 06 00 30 22 01 00 00 06 00 08 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 88 31
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00

00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, medium devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d0100000-d01fffff
	Prefetchable memory behind bridge: d8000000-dfffffff
	Capabilities: [80] Power Management version 2
00: 06 11 88 b1 07 00 30 02 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 20 20 20 02
20: 10 d0 10 d0 00 d8 f0 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00

00:07.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02)
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 168, IRQ 16
	Memory at 68000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 60000000-63fff000 (prefetchable)
	Memory window 1: 64000000-67fff000
	I/O window 0: 00001c00-00001cff
	I/O window 1: 00003000-000030ff
	16-bit legacy interface ports at 0001
00: 4c 10 44 ac 07 00 10 02 02 00 07 06 10 a8 82 00
10: 00 00 00 68 a0 00 00 02 00 02 05 b0 00 00 00 60
20: 00 f0 ff 63 00 00 00 64 00 f0 ff 67 00 1c 00 00
30: fc 1c 00 00 00 30 00 00 fc 30 00 00 ff 01 c0 05
40: 25 10 57 00 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:07.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller (prog-if 10 [OHCI])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 64, IRQ 17
	Memory at d0015000 (32-bit, non-prefetchable) [size=2K]
	Memory at d0010000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 2
00: 4c 10 29 80 16 00 10 02 00 10 00 0c 10 40 80 00
10: 00 50 01 d0 00 00 01 d0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 03 04

00:09.0 Network controller: Intel Corporation PRO/Wireless 2915ABG Network Connection (rev 05)
	Subsystem: Intel Corporation Unknown device 1001
	Flags: bus master, medium devsel, latency 64, IRQ 19
	Memory at d0014000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2
00: 86 80 23 42 16 00 90 02 05 00 80 02 10 40 00 00
10: 00 40 01 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 01 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 03 18

00:0b.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	Memory at d0000000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: [48] Power Management version 2
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
00: e4 14 9c 16 06 00 b0 02 03 00 00 02 10 40 00 00
10: 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 57 00
30: 00 00 00 00 48 00 00 00 00 00 00 00 09 01 40 00

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 64, IRQ 18
	I/O ports at 1800 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 80 00 03 0c 10 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 18 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 01 00 00

00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 64, IRQ 18
	I/O ports at 1820 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 80 00 03 0c 10 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 21 18 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 02 00 00

00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 64, IRQ 18
	I/O ports at 1840 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 80 00 03 0c 10 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 18 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 03 00 00

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 64, IRQ 18
	Memory at d0015800 (32-bit, non-prefetchable) [size=256]
	Capabilities: [80] Power Management version 2
00: 06 11 04 31 17 00 10 02 82 20 03 0c 10 40 00 00
10: 00 58 01 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 04 00 00

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, stepping, medium devsel, latency 0
	Capabilities: [c0] Power Management version 2
00: 06 11 77 31 87 00 10 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, medium devsel, latency 64
	[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
	[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
	I/O ports at 1860 [size=16]
	Capabilities: [c0] Power Management version 2
00: 06 11 71 05 05 00 90 02 06 8a 01 01 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 61 18 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 01 00 00

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: medium devsel, IRQ 20
	I/O ports at 1000 [size=256]
	Capabilities: [c0] Power Management version 2
00: 06 11 59 30 01 00 10 02 50 00 01 04 00 00 00 00
10: 01 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0b 03 00 00

00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: medium devsel, IRQ 20
	I/O ports at 1400 [size=256]
	Capabilities: [d0] Power Management version 2
00: 06 11 68 30 01 00 10 02 80 00 80 07 00 00 00 00
10: 01 14 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 d0 00 00 00 00 00 00 00 0b 03 00 00

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
	Flags: fast devsel
	Capabilities: [80] HyperTransport: Host or Secondary Interface
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
	Flags: fast devsel
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
	Flags: fast devsel
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
	Flags: fast devsel
00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] (prog-if 00 [VGA])
	Subsystem: Acer Incorporated [ALI] Unknown device 0057
	Flags: bus master, 66MHz, medium devsel, latency 66, IRQ 21
	Memory at d8000000 (32-bit, prefetchable) [size=128M]
	I/O ports at 2000 [size=256]
	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
	Capabilities: [58] AGP version 3.0
	Capabilities: [50] Power Management version 2
00: 02 10 50 4e 07 00 b0 02 00 00 00 03 10 42 00 00
10: 08 00 00 d8 01 20 00 00 00 00 10 d0 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 57 00
30: 00 00 00 00 58 00 00 00 00 00 00 00 05 01 08 00



  reply	other threads:[~2007-05-18  9:46 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-05-17 19:01 pata_via appears to incorrectly detects 40-pin cable Francis Russell
2007-05-17 20:16 ` Claas Langbehn
2007-05-17 21:15   ` Francis Russell
2007-05-18  0:39 ` Alan Cox
2007-05-18  9:46   ` Francis Russell [this message]
  -- strict thread matches above, loose matches on Subject: below --
2007-05-17 19:04 Francis Russell

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=464D7603.7010308@btinternet.com \
    --to=francisrussell@btinternet.com \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.