From: Robert Hancock <hancockr@shaw.ca>
To: Thomas Voegtle <tv@lio96.de>
Cc: linux-kernel@vger.kernel.org
Subject: Re: hisax isdn card (Sedlbauer Speed Fax+) does not get an interrupt
Date: Thu, 31 May 2007 08:37:52 -0600 [thread overview]
Message-ID: <465EDDC0.6090601@shaw.ca> (raw)
In-Reply-To: <fa./GDxiXMgfJlsQXnkvKu3TibPJV8@ifi.uio.no>
Thomas Voegtle wrote:
> Hi,
>
> after finally upgrading our systems from Kernel 2.4 to 2.6 we experienced
> problems with the ISDN cards, a hisax driven Sedlbauer Speed Fax+.
>
>
> A "modprobe hisax type=28 protocol=2" ends in this mess:
>
> ==========================================================================
> <05>2007 May 30 14:21:40 cbs kern: ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Linux Driver for passive ISDN cards
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Version 3.5 (module)
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Layer1 Revision 2.46.2.5
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Layer2 Revision 2.30.2.4
> <06>2007 May 30 14:21:40 cbs kern: HiSax: TeiMgr Revision 2.20.2.3
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Layer3 Revision 2.22.2.3
> <06>2007 May 30 14:21:40 cbs kern: HiSax: LinkLayer Revision 2.59.2.4
> <06>2007 May 30 14:21:40 cbs kern: HiSax module removed
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Linux Driver for passive ISDN cards
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Version 3.5 (module)
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Layer1 Revision 2.46.2.5
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Layer2 Revision 2.30.2.4
> <06>2007 May 30 14:21:40 cbs kern: HiSax: TeiMgr Revision 2.20.2.3
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Layer3 Revision 2.22.2.3
> <06>2007 May 30 14:21:40 cbs kern: HiSax: LinkLayer Revision 2.59.2.4
> <07>2007 May 30 14:21:40 cbs kern: HiSax: Total 1 card defined
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Card 1 Protocol EDSS1 Id=isdn0 (0)
> <06>2007 May 30 14:21:40 cbs kern: HiSax: Sedlbauer driver Rev. 1.34.2.6
> <06>2007 May 30 14:21:40 cbs kern: ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: PCI subvendor:51 subid 1
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: PCI base adr 0xa800
> <03>2007 May 30 14:21:40 cbs kern: irq 11: nobody cared (try booting with the \"irqpoll\" option)
> <04>2007 May 30 14:21:40 cbs kern: [<c012f243>] __report_bad_irq+0x2b/0x69
> <04>2007 May 30 14:21:40 cbs kern: [<c012f3e7>] note_interrupt+0x166/0x193
> <04>2007 May 30 14:21:40 cbs kern: [<c03089c0>] usb_hcd_irq+0x23/0x4f
> <04>2007 May 30 14:21:40 cbs kern: [<c012ee7c>] handle_IRQ_event+0x21/0x4a
> <04>2007 May 30 14:21:40 cbs kern: [<c012ef0d>] __do_IRQ+0x68/0x8f
> <04>2007 May 30 14:21:40 cbs kern: [<c01050de>] do_IRQ+0x5c/0x77
> <04>2007 May 30 14:21:40 cbs kern: =======================
> <04>2007 May 30 14:21:40 cbs kern: [<c0103ada>] common_interrupt+0x1a/0x20
> <04>2007 May 30 14:21:40 cbs kern: [<c011a87c>] __do_softirq+0x2c/0x7d
> <04>2007 May 30 14:21:40 cbs kern: [<c0105131>] do_softirq+0x38/0x3f
> <04>2007 May 30 14:21:40 cbs kern: =======================
> <04>2007 May 30 14:21:40 cbs kern: [<c01050f0>] do_IRQ+0x6e/0x77
> <04>2007 May 30 14:21:40 cbs kern: [<c0103ada>] common_interrupt+0x1a/0x20
> <04>2007 May 30 14:21:40 cbs kern: [<d894007b>] W6692B_interrupt+0x23c/0x559 [hisax]
> <04>2007 May 30 14:21:40 cbs kern: [<c010b893>] delay_pmtmr+0xb/0x13
> <04>2007 May 30 14:21:40 cbs kern: [<c01b73f5>] __delay+0x9/0xa
> <04>2007 May 30 14:21:40 cbs kern: [<d892f834>] setup_sedlbauer+0x1ee/0x534 [hisax]
> <04>2007 May 30 14:21:40 cbs kern: [<c01175e8>] printk+0x12/0x16
> <04>2007 May 30 14:21:40 cbs kern: [<d890dcdb>] checkcard+0x201/0x566 [hisax]
> <04>2007 May 30 14:21:40 cbs kern: [<d890dd62>] checkcard+0x288/0x566 [hisax]
> <04>2007 May 30 14:21:40 cbs kern: [<d88554dc>] HiSax_init+0x4dc/0x57a [hisax]
> <04>2007 May 30 14:21:40 cbs kern: [<c0159693>] new_inode+0x14/0x76
> <04>2007 May 30 14:21:40 cbs kern: [<c017340c>] sysfs_add_file+0x1f/0x52
> <04>2007 May 30 14:21:40 cbs kern: [<c01275fc>] debug_mutex_add_waiter+0x14/0x24
> <04>2007 May 30 14:21:40 cbs kern: [<c0173995>] sysfs_new_dirent+0x17/0x56
> <04>2007 May 30 14:21:40 cbs kern: [<c012a782>] sys_init_module+0x1364/0x1439
> <04>2007 May 30 14:21:40 cbs kern: [<c013711c>] vma_prio_tree_insert+0x17/0x2a
> <04>2007 May 30 14:21:40 cbs kern: [<c013ac54>] vma_link+0x85/0x8b
> <04>2007 May 30 14:21:40 cbs kern: [<c013c7a4>] do_mmap_pgoff+0x4e7/0x634
> <04>2007 May 30 14:21:40 cbs kern: [<c0106f44>] sys_mmap2+0x61/0x90
> <04>2007 May 30 14:21:40 cbs kern: [<c0102a79>] syscall_call+0x7/0xb
> <03>2007 May 30 14:21:40 cbs kern: handlers:
> <03>2007 May 30 14:21:40 cbs kern: [<c030899d>] (usb_hcd_irq+0x0/0x4f)
> <00>2007 May 30 14:21:40 cbs kern: Disabling IRQ #11
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: defined at 0xa800-0xa900 IRQ 11
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: speed fax+ pyramid detected
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: ISAC version (0): 2086/2186 V1.1
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: ISAR version 1
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ 11 count 100000
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ 11 count 100000
> <04>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ(11) getting no interrupts during init 1
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ 11 count 100000
> <04>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ(11) getting no interrupts during init 2
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ 11 count 100000
> <04>2007 May 30 14:21:40 cbs kern: Sedlbauer Speed Fax +: IRQ(11) getting no interrupts during init 3
> <06>2007 May 30 14:21:40 cbs kern: Sedlbauer: resetting card
> <04>2007 May 30 14:21:40 cbs kern: HiSax: Card Sedlbauer Speed Fax + not installed !
> ==========================================================================
>
> While the output seems to suggest a hardware problem, the same system
> loads the hisax driver perfectly on recent 2.4 kernels.
>
> We tried several kernel versions, up to 2.6.21.3
>
> Any hints are appreciated :)
Likely a driver problem - the device is using IRQ 11, but the driver
never actually registered a handler for that interrupt (it's not in the
list of handlers, only USB is). Maybe retrieving the interrupt before
pci_enable_device? (I haven't looked at the code in question.)
--
Robert Hancock Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/
next parent reply other threads:[~2007-05-31 14:38 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <fa./GDxiXMgfJlsQXnkvKu3TibPJV8@ifi.uio.no>
2007-05-31 14:37 ` Robert Hancock [this message]
2007-06-04 9:24 ` hisax isdn card (Sedlbauer Speed Fax+) does not get an interrupt Thomas Voegtle
2007-06-04 14:31 ` Robert Hancock
2007-05-31 13:44 Thomas Voegtle
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=465EDDC0.6090601@shaw.ca \
--to=hancockr@shaw.ca \
--cc=linux-kernel@vger.kernel.org \
--cc=tv@lio96.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.