From: Heiner Kallweit <hkallweit1@gmail.com>
To: Yogesh Gaur <yogeshgaur.83@gmail.com>, nic_swsd@realtek.com
Cc: Andrew Lunn <andrew+netdev@lunn.ch>,
"David S . Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
Javen Xu <javen_xu@realsil.com.cn>
Subject: Re: [PATCH net v2] r8169: don't enable chip LTR when the platform has not enabled LTR
Date: Thu, 10 Sep 2026 21:33:15 +0200 [thread overview]
Message-ID: <46807790-6f07-4f0a-b50b-375cc1c9b061@gmail.com> (raw)
In-Reply-To: <20260910130140.910-1-yogeshgaur.83@gmail.com>
On 10.09.2026 15:01, Yogesh Gaur wrote:
> rtl_enable_ltr() programs the MAC to generate LTR messages - ALDPS_LTR_EN,
>
Empty lines, mail formatting issue?
> LTR_SNOOP_EN, LTR_OBFF_LOCK_EN, plus LINK_SPEED_CHANGE_EN on
>
> RTL8125/RTL8126/RTL8127 - and rtl_hw_aspm_clkreq_enable() calls it on
>
> every ASPM enable, then goes on to let the chip trigger L1.2.
>
>
>
> The only gate is tp->aspm_manageable, which records that the OS is allowed
>
> to control ASPM. It says nothing about LTR. LTR is a separate PCIe
>
> capability that only works if every device on the path to the root port
>
> supports it. The PCI core works that out in pci_configure_ltr() and
>
> records the result in pci_dev->ltr_path; per PCIe r6.0 sec 7.5.3.16 a
>
> function must not issue LTR messages while LTR Mechanism Enable is clear.
>
>
>
> So on a platform whose hierarchy has no LTR path, the driver tells the
>
> chip to start sending LTR messages nothing will honour, and ties ALDPS -
>
> the PHY's link-down power saving - to them. A report against RTL8125B
>
> (rev 05, firmware rtl8125b-2_0.0.2) in a mini PC shows the effect: 291
Did you verify that this is caused by LTR messages, and not by any other
root cause?
>
> link down/up transitions in one eight-hour boot, with repeated downshifts
>
> to 100Mbps, against four transitions at boot and then a stable link on
>
> the kernel before the LTR change.
>
>
>
> Gate the chip's LTR programming on pci_dev->ltr_path. That field lives
>
> inside CONFIG_PCIEASPM, and without ASPM support there is nothing here to
>
> enable LTR for, so compile the function out in that configuration.
>
>
>
> Note this does change CONFIG_PCIEASPM=n builds, which used to program
>
> chip LTR unconditionally: pci_disable_link_state() is a stub that returns
>
> success there, so tp->aspm_manageable ends up set. The PCI core does not
>
> configure LTR in that configuration either.
>
>
>
> Fixes: 9ab94a32af70 ("r8169: enable LTR support")
>
> Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2529752
Did you verify that your patch fixes the reported issue? Or do you
just assume this? Because in the bug comment history I don't see
a statement that issue has been resolved.
> Assisted-by: LLM
>
> Signed-off-by: Yogesh Gaur <yogeshgaur.83@gmail.com>
>
> ---
>
> v2:
>
> - Gate on pci_dev->ltr_path instead of reading PCI_EXP_DEVCTL2 directly,
>
> and compile rtl_enable_ltr() out for CONFIG_PCIEASPM=n, where that
>
> field does not exist and there is nothing to enable LTR for.
>
> Suggested by Heiner Kallweit.
>
> - Commit message notes the resulting change for CONFIG_PCIEASPM=n builds.
>
> - No change to the RTL8125 register programming itself.
>
>
>
> v1: https://lore.kernel.org/all/20260909110554.1977-1-yogeshgaur.83@gmail.com/
>
>
>
> drivers/net/ethernet/realtek/r8169_main.c | 13 +++++++++++++
>
> 1 file changed, 13 insertions(+)
>
>
>
> diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c
>
> index ec4fc21fa21f..05f7a44aff01 100644
>
> --- a/drivers/net/ethernet/realtek/r8169_main.c
>
> +++ b/drivers/net/ethernet/realtek/r8169_main.c
>
> @@ -3035,8 +3035,16 @@ static void rtl_disable_exit_l1(struct rtl8169_private *tp)
>
> }
>
> }
>
>
>
> +#ifdef CONFIG_PCIEASPM
>
> static void rtl_enable_ltr(struct rtl8169_private *tp)
>
> {
>
> + /* The chip must not issue LTR messages unless LTR is enabled on the
>
> + * whole path up to the root port. pci_configure_ltr() works that out
>
> + * and records the result in pci_dev->ltr_path.
>
> + */
>
> + if (!tp->pci_dev->ltr_path)
Simpler would be:
if (!IS_ENABLED(CONFIG_PCIEASPM) || !tp->pci_dev->ltr_path)
Then you don't need the stub function.
>
> + return;
>
> +
>
> switch (tp->mac_version) {
>
> case RTL_GIGA_MAC_VER_80:
>
> r8168_mac_ocp_write(tp, 0xcdd0, 0x9003);
>
> @@ -3120,6 +3128,11 @@ static void rtl_enable_ltr(struct rtl8169_private *tp)
>
> /* chip can trigger LTR */
>
> r8168_mac_ocp_modify(tp, LTR_OBFF_LOCK, 0x0003, LTR_OBFF_LOCK_EN);
>
> }
>
> +#else
>
> +static void rtl_enable_ltr(struct rtl8169_private *tp)
>
> +{
>
> +}
>
> +#endif
>
>
>
> static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
>
> {
>
next prev parent reply other threads:[~2026-09-10 19:33 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-10 13:01 [PATCH net v2] r8169: don't enable chip LTR when the platform has not enabled LTR Yogesh Gaur
2026-09-10 19:33 ` Heiner Kallweit [this message]
2026-09-11 13:00 ` Yogesh Gaur
2026-09-11 13:14 ` Heiner Kallweit
2026-09-11 13:13 ` [PATCH net v3] " Yogesh Gaur
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46807790-6f07-4f0a-b50b-375cc1c9b061@gmail.com \
--to=hkallweit1@gmail.com \
--cc=andrew+netdev@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=javen_xu@realsil.com.cn \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nic_swsd@realtek.com \
--cc=pabeni@redhat.com \
--cc=yogeshgaur.83@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.