From: Xose Vazquez Perez <xose.vazquez@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Subject: [BUG] ISIC + 2.6.22 (via-rhine)
Date: Tue, 31 Jul 2007 23:11:18 +0200 [thread overview]
Message-ID: <46AFA576.1060902@gmail.com> (raw)
hi,
Running ISIC -- IP Stack Integrity Checker ( http://isic.sf.net ),
in Fedora-7-i386 with 2.6.22, the NIC stopped to send packages.
But one second latter it began to send out more of them.
dmesg shows the bug.
command is:
# tcpsic -s rand -d 172.26.0.2 -I100
driver is:
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
eth0: VIA Rhine II at 0xbc000000, 00:11:d8:54:e9:3c, IRQ 19.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present
---lspci--
00:12.0 0200: 1106:3065 (rev 78)
Subsystem: 1043:80ed
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 7000 [size=256]
Region 1: Memory at bc000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--end--
--dmesg output--
[...]
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0000, PHY status 786d, resetting...
=================================
[ INFO: inconsistent lock state ]
2.6.22 #1
---------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&rp->lock){++..}, at: [<f8c890db>] rhine_tx_timeout+0x6f/0xf4 [via_rhine]
{in-hardirq-W} state was registered at:
[<c04440d4>] __lock_acquire+0x38c/0xb12
[<c0444c1b>] lock_acquire+0x56/0x6f
[<c0615279>] _spin_lock+0x2b/0x38
[<f8c87b49>] rhine_interrupt+0x16b/0x69b [via_rhine]
[<c045aac6>] handle_IRQ_event+0x1a/0x46
[<c045bbc0>] handle_fasteoi_irq+0x7d/0xb6
[<c0407089>] do_IRQ+0xb1/0xd8
[<ffffffff>] 0xffffffff
irq event stamp: 18052892
hardirqs last enabled at (18052892): [<c061567d>] _spin_unlock_irqrestore+0x36/0x3c
hardirqs last disabled at (18052891): [<c061558d>] _spin_lock_irqsave+0x12/0x44
softirqs last enabled at (18052876): [<c042d272>] __do_softirq+0xe3/0xe9
softirqs last disabled at (18052887): [<c0406f72>] do_softirq+0x61/0xc7
other info that might help us debug this:
1 lock held by swapper/0:
#0: (_xmit_ETHER){-+..}, at: [<c05c042a>] dev_watchdog+0x14/0xbf
stack backtrace:
[<c0405e6a>] show_trace_log_lvl+0x1a/0x2f
[<c04068cf>] show_trace+0x12/0x14
[<c0406928>] dump_stack+0x16/0x18
[<c0442ccd>] print_usage_bug+0x141/0x14b
[<c04434fd>] mark_lock+0x1fd/0x409
[<c0444144>] __lock_acquire+0x3fc/0xb12
[<c0444c1b>] lock_acquire+0x56/0x6f
[<c0615279>] _spin_lock+0x2b/0x38
[<f8c890db>] rhine_tx_timeout+0x6f/0xf4 [via_rhine]
[<c05c048c>] dev_watchdog+0x76/0xbf
[<c04303be>] run_timer_softirq+0x11a/0x182
[<c042d1fe>] __do_softirq+0x6f/0xe9
[<c0406f72>] do_softirq+0x61/0xc7
=======================
via-rhine: Reset not complete yet. Trying harder.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
--end---
-thanks-
--
Politicos de mierda, yo no soy un terrorista.
next reply other threads:[~2007-07-31 21:11 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-07-31 21:11 Xose Vazquez Perez [this message]
2007-07-31 21:23 ` [BUG] ISIC + 2.6.22 (via-rhine) Arjan van de Ven
2007-07-31 21:53 ` Xose Vazquez Perez
-- strict thread matches above, loose matches on Subject: below --
2007-07-09 17:31 Xose Vazquez Perez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46AFA576.1060902@gmail.com \
--to=xose.vazquez@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.