From: Mike Rapoport <mike@compulab.co.il>
To: u-boot@lists.denx.de
Subject: [U-Boot-Users] [PATCH] Add more PXA27x-specific registers to include/asm-arm/arch-pxa/pxa-regs.h
Date: Tue, 07 Aug 2007 13:33:57 +0300 [thread overview]
Message-ID: <46B84A95.2080800@compulab.co.il> (raw)
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
include/asm-arm/arch-pxa/pxa-regs.h | 338 +++++++++++++++++++++++++++++++++--
1 files changed, 326 insertions(+), 12 deletions(-)
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index ebda719..0700044 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -150,6 +150,7 @@ typedef void (*ExcpHndlr) (void) ;
#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
+#define DALGN __REG(0x400000a0) /* DMA Alignment Register */
#define DINT __REG(0x400000f0) /* DMA Interrupt Register */
#define DRCMR0 __REG(0x40000100) /* Request to Channel Map Register for DREQ 0 */
@@ -210,12 +211,17 @@ typedef void (*ExcpHndlr) (void) ;
#define DRCMRTXPCDR DRCMR12
#define DRCMRRXSSDR DRCMR13
#define DRCMRTXSSDR DRCMR14
+#define DRCMRRXSS2DR DRCMR15
+#define DRCMRTXSS2DR DRCMR16
#define DRCMRRXICDR DRCMR17
#define DRCMRTXICDR DRCMR18
#define DRCMRRXSTRBR DRCMR19
#define DRCMRTXSTTHR DRCMR20
#define DRCMRRXMMC DRCMR21
#define DRCMRTXMMC DRCMR22
+#define DRCMRRXSS3DR DRCMR66
+#define DRCMRTXSS3DR DRCMR67
+#define DRCMRUDC(x) DRCMR((x) + 24)
#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */
#define DRCMR_CHLNUM 0x0f /* mask for Channel Number (read / write) */
@@ -521,14 +527,18 @@ typedef void (*ExcpHndlr) (void) ;
*/
#define POCR __REG(0x40500000) /* PCM Out Control Register */
#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define PICR __REG(0x40500004) /* PCM In Control Register */
#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MCCR __REG(0x40500008) /* Mic In Control Register */
#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define GCR __REG(0x4050000C) /* Global Control Register */
+#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
@@ -542,12 +552,17 @@ typedef void (*ExcpHndlr) (void) ;
#define POSR __REG(0x40500010) /* PCM Out Status Register */
#define POSR_FIFOE (1 << 4) /* FIFO error */
+#define POSR_FSR (1 << 2) /* FIFO Service Request */
#define PISR __REG(0x40500014) /* PCM In Status Register */
#define PISR_FIFOE (1 << 4) /* FIFO error */
+#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define PISR_FSR (1 << 2) /* FIFO Service Request */
#define MCSR __REG(0x40500018) /* Mic In Status Register */
#define MCSR_FIFOE (1 << 4) /* FIFO error */
+#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MCSR_FSR (1 << 2) /* FIFO Service Request */
#define GSR __REG(0x4050001C) /* Global Status Register */
#define GSR_CDONE (1 << 19) /* Command Done */
@@ -563,6 +578,7 @@ typedef void (*ExcpHndlr) (void) ;
#define GSR_MINT (1 << 7) /* Mic In Interrupt */
#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
+#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */
#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
@@ -575,15 +591,20 @@ typedef void (*ExcpHndlr) (void) ;
#define MOCR __REG(0x40500100) /* Modem Out Control Register */
#define MOCR_FEIE (1 << 3) /* FIFO Error */
+#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MICR __REG(0x40500108) /* Modem In Control Register */
#define MICR_FEIE (1 << 3) /* FIFO Error */
+#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MOSR __REG(0x40500110) /* Modem Out Status Register */
#define MOSR_FIFOE (1 << 4) /* FIFO error */
+#define MOSR_FSR (1 << 2) /* FIFO Service Request */
#define MISR __REG(0x40500118) /* Modem In Status Register */
#define MISR_FIFOE (1 << 4) /* FIFO error */
+#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MISR_FSR (1 << 2) /* FIFO Service Request */
#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
@@ -594,7 +615,10 @@ typedef void (*ExcpHndlr) (void) ;
/*
* USB Device Controller
+ * PXA25x and PXA27x USB device controller registers are different.
*/
+#if defined(CONFIG_PXA25x)
+
#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */
#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */
#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */
@@ -663,7 +687,7 @@ typedef void (*ExcpHndlr) (void) ;
#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
+#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */
#define UDCCS_IO_DME (1 << 3) /* DMA enable */
#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
@@ -750,7 +774,258 @@ typedef void (*ExcpHndlr) (void) ;
#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
-#if defined(CONFIG_PXA27X)
+#elif defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+
+#define UDCCR __REG(0x40600000) /* UDC Control Register */
+#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */
+#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation
+ Protocol Port Support */
+#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol
+ Support */
+#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol
+ Enable */
+#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */
+#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */
+#define UDCCR_ACN_S 11
+#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */
+#define UDCCR_AIN_S 8
+#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface
+ Setting Number */
+#define UDCCR_AAISN_S 5
+#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active
+ Configuration */
+#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration
+ Error */
+#define UDCCR_UDR (1 << 2) /* UDC Resume */
+#define UDCCR_UDA (1 << 1) /* UDC Active */
+#define UDCCR_UDE (1 << 0) /* UDC Enable */
+
+#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */
+#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */
+#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */
+#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */
+
+#define UDC_INT_FIFOERROR (0x2)
+#define UDC_INT_PACKETCMP (0x1)
+
+#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
+#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */
+#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */
+#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */
+#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */
+#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */
+
+#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */
+#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */
+#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
+#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */
+#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */
+#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */
+#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */
+#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */
+
+#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */
+#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */
+#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */
+#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt
+ Rising Edge Interrupt Enable */
+#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt
+ Falling Edge Interrupt Enable */
+#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising
+ Edge Interrupt Enable */
+#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling
+ Edge Interrupt Enable */
+#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge
+ Interrupt Enable */
+
+#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */
+
+#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */
+#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */
+#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */
+#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */
+#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */
+#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */
+#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */
+#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */
+#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */
+#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */
+#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */
+#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */
+#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */
+#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */
+
+#define UDCCSN(x) __REG2(0x40600100, (x) << 2)
+#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */
+#define UDCCSR0_SA (1 << 7) /* Setup Active */
+#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */
+#define UDCCSR0_FST (1 << 5) /* Force Stall */
+#define UDCCSR0_SST (1 << 4) /* Sent Stall */
+#define UDCCSR0_DME (1 << 3) /* DMA Enable */
+#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */
+#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */
+#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */
+
+#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */
+#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */
+#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */
+#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */
+#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */
+#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */
+#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */
+#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */
+#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */
+#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */
+#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */
+#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */
+#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */
+#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */
+#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */
+#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */
+#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */
+#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */
+#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */
+#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */
+#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */
+#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */
+#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */
+
+#define UDCCSR_DPE (1 << 9) /* Data Packet Error */
+#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */
+#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */
+#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */
+#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */
+#define UDCCSR_FST (1 << 5) /* Force STALL */
+#define UDCCSR_SST (1 << 4) /* Sent STALL */
+#define UDCCSR_DME (1 << 3) /* DMA Enable */
+#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */
+#define UDCCSR_PC (1 << 1) /* Packet Complete */
+#define UDCCSR_FS (1 << 0) /* FIFO needs service */
+
+#define UDCBCN(x) __REG2(0x40600200, (x)<<2)
+#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */
+#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */
+#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */
+#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */
+#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */
+#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */
+#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */
+#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */
+#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */
+#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */
+#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */
+#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */
+#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */
+#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */
+#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */
+#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */
+#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */
+#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */
+#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */
+#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */
+#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */
+#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */
+#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */
+#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */
+
+#define UDCDN(x) __REG2(0x40600300, (x)<<2)
+#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2))
+#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x))))
+#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */
+#define UDCDRA __REG(0x40600304) /* Data Register - EPA */
+#define UDCDRB __REG(0x40600308) /* Data Register - EPB */
+#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */
+#define UDCDRD __REG(0x40600310) /* Data Register - EPD */
+#define UDCDRE __REG(0x40600314) /* Data Register - EPE */
+#define UDCDRF __REG(0x40600318) /* Data Register - EPF */
+#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */
+#define UDCDRH __REG(0x40600320) /* Data Register - EPH */
+#define UDCDRI __REG(0x40600324) /* Data Register - EPI */
+#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */
+#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */
+#define UDCDRL __REG(0x40600330) /* Data Register - EPL */
+#define UDCDRM __REG(0x40600334) /* Data Register - EPM */
+#define UDCDRN __REG(0x40600338) /* Data Register - EPN */
+#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */
+#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */
+#define UDCDRR __REG(0x40600344) /* Data Register - EPR */
+#define UDCDRS __REG(0x40600348) /* Data Register - EPS */
+#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */
+#define UDCDRU __REG(0x40600350) /* Data Register - EPU */
+#define UDCDRV __REG(0x40600354) /* Data Register - EPV */
+#define UDCDRW __REG(0x40600358) /* Data Register - EPW */
+#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */
+
+#define UDCCN(x) __REG2(0x40600400, (x)<<2)
+#define UDCCRA __REG(0x40600404) /* Configuration register EPA */
+#define UDCCRB __REG(0x40600408) /* Configuration register EPB */
+#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */
+#define UDCCRD __REG(0x40600410) /* Configuration register EPD */
+#define UDCCRE __REG(0x40600414) /* Configuration register EPE */
+#define UDCCRF __REG(0x40600418) /* Configuration register EPF */
+#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */
+#define UDCCRH __REG(0x40600420) /* Configuration register EPH */
+#define UDCCRI __REG(0x40600424) /* Configuration register EPI */
+#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */
+#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */
+#define UDCCRL __REG(0x40600430) /* Configuration register EPL */
+#define UDCCRM __REG(0x40600434) /* Configuration register EPM */
+#define UDCCRN __REG(0x40600438) /* Configuration register EPN */
+#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */
+#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */
+#define UDCCRR __REG(0x40600444) /* Configuration register EPR */
+#define UDCCRS __REG(0x40600448) /* Configuration register EPS */
+#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */
+#define UDCCRU __REG(0x40600450) /* Configuration register EPU */
+#define UDCCRV __REG(0x40600454) /* Configuration register EPV */
+#define UDCCRW __REG(0x40600458) /* Configuration register EPW */
+#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */
+
+#define UDCCONR_CN (0x03 << 25) /* Configuration Number */
+#define UDCCONR_CN_S (25)
+#define UDCCONR_IN (0x07 << 22) /* Interface Number */
+#define UDCCONR_IN_S (22)
+#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */
+#define UDCCONR_AISN_S (19)
+#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */
+#define UDCCONR_EN_S (15)
+#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */
+#define UDCCONR_ET_S (13)
+#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */
+#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */
+#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */
+#define UDCCONR_ET_NU (0x00 << 13) /* Not used */
+#define UDCCONR_ED (1 << 12) /* Endpoint Direction */
+#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */
+#define UDCCONR_MPS_S (2)
+#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */
+#define UDCCONR_EE (1 << 0) /* Endpoint Enable */
+
+
+#define UDC_INT_FIFOERROR (0x2)
+#define UDC_INT_PACKETCMP (0x1)
+
+#define UDC_FNR_MASK (0x7ff)
+
+#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST)
+#define UDC_BCR_MASK (0x3ff)
+#endif
+
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
/*
* USB Host Controller
*/
@@ -1269,15 +1544,15 @@ typedef void (*ExcpHndlr) (void) ;
#define _GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3)
#define _GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2)
-#define GPLR(x) ((((x) & 0x7f) < 96) ? _GPLR(x) : GPLR3)
-#define GPDR(x) ((((x) & 0x7f) < 96) ? _GPDR(x) : GPDR3)
-#define GPSR(x) ((((x) & 0x7f) < 96) ? _GPSR(x) : GPSR3)
-#define GPCR(x) ((((x) & 0x7f) < 96) ? _GPCR(x) : GPCR3)
-#define GRER(x) ((((x) & 0x7f) < 96) ? _GRER(x) : GRER3)
-#define GFER(x) ((((x) & 0x7f) < 96) ? _GFER(x) : GFER3)
-#define GEDR(x) ((((x) & 0x7f) < 96) ? _GEDR(x) : GEDR3)
-#define GAFR(x) ((((x) & 0x7f) < 96) ? _GAFR(x) : \
- ((((x) & 0x7f) < 112) ? GAFR3_L : GAFR3_U))
+#define GPLR(x) (*((((x) & 0x7f) < 96) ? &_GPLR(x) : &GPLR3))
+#define GPDR(x) (*((((x) & 0x7f) < 96) ? &_GPDR(x) : &GPDR3))
+#define GPSR(x) (*((((x) & 0x7f) < 96) ? &_GPSR(x) : &GPSR3))
+#define GPCR(x) (*((((x) & 0x7f) < 96) ? &_GPCR(x) : &GPCR3))
+#define GRER(x) (*((((x) & 0x7f) < 96) ? &_GRER(x) : &GRER3))
+#define GFER(x) (*((((x) & 0x7f) < 96) ? &_GFER(x) : &GFER3))
+#define GEDR(x) (*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3))
+#define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \
+ ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U)))
#else
#define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3)
@@ -1319,6 +1594,8 @@ typedef void (*ExcpHndlr) (void) ;
#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */
#define GPIO31_SYNC 31 /* AC97/I2S sync */
#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */
+#define GPIO32_SYSCLK 32 /* I2S System Clock */
+#define GPIO32_MMCCLK 32 /* MMC Clock (PXA270) */
#define GPIO33_nCS_5 33 /* chip select 5 */
#define GPIO34_FFRXD 34 /* FFUART receive */
#define GPIO34_MMCCS0 34 /* MMC Chip Select 0 */
@@ -1381,6 +1658,21 @@ typedef void (*ExcpHndlr) (void) ;
#define GPIO78_nCS_2 78 /* chip select 2 */
#define GPIO79_nCS_3 79 /* chip select 3 */
#define GPIO80_nCS_4 80 /* chip select 4 */
+#define GPIO81_NSCLK 81 /* NSSP clock */
+#define GPIO82_NSFRM 82 /* NSSP Frame */
+#define GPIO83_NSTXD 83 /* NSSP transmit */
+#define GPIO84_NSRXD 84 /* NSSP receive */
+#define GPIO85_nPCE_1 85 /* Card Enable for Card Space (PXA27x) */
+#define GPIO92_MMCDAT0 92 /* MMC DAT0 (PXA27x) */
+#define GPIO102_nPCE_1 102 /* PCMCIA (PXA27x) */
+#define GPIO109_MMCDAT1 109 /* MMC DAT1 (PXA27x) */
+#define GPIO110_MMCDAT2 110 /* MMC DAT2 (PXA27x) */
+#define GPIO110_MMCCS0 110 /* MMC Chip Select 0 (PXA27x) */
+#define GPIO111_MMCDAT3 111 /* MMC DAT3 (PXA27x) */
+#define GPIO111_MMCCS1 111 /* MMC Chip Select 1 (PXA27x) */
+#define GPIO112_MMCCMD 112 /* MMC CMD (PXA27x) */
+#define GPIO113_I2S_SYSCLK 113 /* I2S System Clock (PXA27x) */
+#define GPIO113_AC97_RESET_N 113 /* AC97 NRESET on (PXA27x) */
/* GPIO alternate function mode & direction */
@@ -1426,6 +1718,8 @@ typedef void (*ExcpHndlr) (void) ;
#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT)
#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN)
+#define GPIO32_SYSCLK_I2S_MD (32 | GPIO_ALT_FN_1_OUT)
+#define GPIO32_MMCCLK_MD ( 32 | GPIO_ALT_FN_2_OUT)
#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT)
#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN)
#define GPIO34_MMCCS0_MD (34 | GPIO_ALT_FN_2_OUT)
@@ -1488,7 +1782,26 @@ typedef void (*ExcpHndlr) (void) ;
#define GPIO78_nCS_2_MD (78 | GPIO_ALT_FN_2_OUT)
#define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT)
#define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT)
-
+#define GPIO81_NSSP_CLK_OUT (81 | GPIO_ALT_FN_1_OUT)
+#define GPIO81_NSSP_CLK_IN (81 | GPIO_ALT_FN_1_IN)
+#define GPIO82_NSSP_FRM_OUT (82 | GPIO_ALT_FN_1_OUT)
+#define GPIO82_NSSP_FRM_IN (82 | GPIO_ALT_FN_1_IN)
+#define GPIO83_NSSP_TX (83 | GPIO_ALT_FN_1_OUT)
+#define GPIO83_NSSP_RX (83 | GPIO_ALT_FN_2_IN)
+#define GPIO84_NSSP_TX (84 | GPIO_ALT_FN_1_OUT)
+#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN)
+#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT)
+#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT)
+#define GPIO102_nPCE_1_MD (102 | GPIO_ALT_FN_1_OUT)
+#define GPIO104_pSKTSEL_MD (104 | GPIO_ALT_FN_1_OUT)
+#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT)
+#define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT)
+#define GPIO110_MMCCS0_MD (110 | GPIO_ALT_FN_1_OUT)
+#define GPIO111_MMCDAT3_MD (111 | GPIO_ALT_FN_1_OUT)
+#define GPIO110_MMCCS1_MD (111 | GPIO_ALT_FN_1_OUT)
+#define GPIO112_MMCCMD_MD (112 | GPIO_ALT_FN_1_OUT)
+#define GPIO113_I2S_SYSCLK_MD (113 | GPIO_ALT_FN_1_OUT)
+#define GPIO113_AC97_RESET_N_MD (113 | GPIO_ALT_FN_2_OUT)
#define GPIO117_SCL (117 | GPIO_ALT_FN_1_OUT)
#define GPIO118_SDA (118 | GPIO_ALT_FN_1_OUT)
@@ -1816,6 +2129,7 @@ typedef void (*ExcpHndlr) (void) ;
#define LCCR1 __REG(0x44000004) /* LCD Controller Control Register 1 */
#define LCCR2 __REG(0x44000008) /* LCD Controller Control Register 2 */
#define LCCR3 __REG(0x4400000C) /* LCD Controller Control Register 3 */
+#define LCCR4 __REG(0x44000010) /* LCD Controller Control Register 3 */
#define DFBR0 __REG(0x44000020) /* DMA Channel 0 Frame Branch Register */
#define DFBR1 __REG(0x44000024) /* DMA Channel 1 Frame Branch Register */
#define LCSR0 __REG(0x44000038) /* LCD Controller Status Register */
next reply other threads:[~2007-08-07 10:33 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-08-07 10:33 Mike Rapoport [this message]
2007-08-07 15:30 ` [U-Boot-Users] [PATCH] [try2] Add more PXA27x-specific registers to include/asm-arm/arch-pxa/pxa-regs.h Mike Rapoport
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46B84A95.2080800@compulab.co.il \
--to=mike@compulab.co.il \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.