From: Brad Campbell <brad@wasp.net.au>
To: Tejun Heo <htejun@gmail.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: Still having problems with sata_promise on all late kernels - shutdown too - BISECTED
Date: Wed, 15 Aug 2007 20:18:07 +0400 [thread overview]
Message-ID: <46C3273F.1070306@wasp.net.au> (raw)
In-Reply-To: <46C2B046.7060708@gmail.com>
Tejun Heo wrote:
> Brad Campbell wrote:
>> Brad Campbell wrote:
>>
>>> http://www.fnarfbargle.com/CIMG1029.JPG (I have posted this screen
>>> shot previously. It's still doing exactly the same thing on both boxes).
>>>
>> git-bisect shows up this commit as the guilty party. I can't just revert
>> it on a recent tree though.
>> Will investigate further.
>
> Weird. Does 'hdparm -y /dev/sdX' work?
Very interesting indeed..
for i in /dev/sd* ; do echo $i ; hdparm -y $i ; done
sda-sdh worked fine.. sdi locked the box.
So it's dying on the 3rd or 4th controller.
Now that I think about it, on the other side of the git bisect I probably only heard 8 clicks as the
kernel shut down the 1st 8 drives, then the remainder powered off when the machine powered off.
So even prior to this it was probably only shutting down the 1st 8 drives properly.
brad@storage1:~$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:09.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] (rev 12)
00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0d.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0e.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master
IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller
(rev 60)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
00:13.0 Mass storage controller: Promise Technology, Inc. PDC20318 (SATA150 TX4) (rev 02)
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 315PRO PCI/AGP VGA Display Adapter
[ 46.624922] sata_promise 0000:00:0b.0: version 2.07
[ 46.624937] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 17
[ 46.641073] scsi0 : sata_promise
[ 46.641301] scsi1 : sata_promise
[ 46.641471] scsi2 : sata_promise
[ 46.648281] scsi3 : sata_promise
[ 46.654924] ata1: SATA max UDMA/133 cmd 0xf8816200 ctl 0xf8816238 bmdma 0x00000000 irq 0
[ 46.661784] ata2: SATA max UDMA/133 cmd 0xf8816280 ctl 0xf88162b8 bmdma 0x00000000 irq 0
[ 46.668432] ata3: SATA max UDMA/133 cmd 0xf8816300 ctl 0xf8816338 bmdma 0x00000000 irq 0
[ 46.674895] ata4: SATA max UDMA/133 cmd 0xf8816380 ctl 0xf88163b8 bmdma 0x00000000 irq 0
[ 47.170019] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 47.190471] ata1.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.197090] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 47.203704] ata1.00: 490234752 sectors, multi 0: LBA48
[ 47.230410] ata1.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.237100] ata1.00: configured for UDMA/133
[ 47.729427] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 47.749866] ata2.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.756760] ata2.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 47.763727] ata2.00: 490234752 sectors, multi 0: LBA48
[ 47.789820] ata2.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 47.796966] ata2.00: configured for UDMA/133
[ 48.288835] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 48.309277] ata3.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.316381] ata3.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 48.323494] ata3.00: 490234752 sectors, multi 0: LBA48
[ 48.349233] ata3.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.356411] ata3.00: configured for UDMA/133
[ 48.848245] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 48.868684] ata4.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.875960] ata4.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 48.883230] ata4.00: 490234752 sectors, multi 0: LBA48
[ 48.908634] ata4.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 48.916000] ata4.00: configured for UDMA/133
[ 48.923402] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 48.931040] sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB)
[ 48.938540] sd 0:0:0:0: [sda] Write Protect is off
[ 48.945849] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 48.945865] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 48.953425] sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB)
[ 48.960907] sd 0:0:0:0: [sda] Write Protect is off
[ 48.968251] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 48.968265] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 48.975808] sda: unknown partition table
[ 55.984630] sd 0:0:0:0: [sda] Attached SCSI disk
[ 55.992218] scsi 1:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 55.999870] sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB)
[ 56.007421] sd 1:0:0:0: [sdb] Write Protect is off
[ 56.015029] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 56.015045] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.023013] sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB)
[ 56.031098] sd 1:0:0:0: [sdb] Write Protect is off
[ 56.039005] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 56.039019] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.047244] sdb: unknown partition table
[ 63.431266] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 63.439764] scsi 2:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 63.448337] sd 2:0:0:0: [sdc] 490234752 512-byte hardware sectors (251000 MB)
[ 63.456799] sd 2:0:0:0: [sdc] Write Protect is off
[ 63.465117] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 63.465133] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 63.473672] sd 2:0:0:0: [sdc] 490234752 512-byte hardware sectors (251000 MB)
[ 63.482133] sd 2:0:0:0: [sdc] Write Protect is off
[ 63.490472] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 63.490486] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 63.498998] sdc: unknown partition table
[ 70.770909] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 70.779326] scsi 3:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 70.787888] sd 3:0:0:0: [sdd] 490234752 512-byte hardware sectors (251000 MB)
[ 70.796358] sd 3:0:0:0: [sdd] Write Protect is off
[ 70.804686] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.804700] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.813235] sd 3:0:0:0: [sdd] 490234752 512-byte hardware sectors (251000 MB)
[ 70.821679] sd 3:0:0:0: [sdd] Write Protect is off
[ 70.829976] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 70.829991] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.838476] sdd: unknown partition table
[ 78.098488] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 78.106864] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 18
[ 78.127345] scsi4 : sata_promise
[ 78.135687] scsi5 : sata_promise
[ 78.143830] scsi6 : sata_promise
[ 78.151848] scsi7 : sata_promise
[ 78.159669] ata5: SATA max UDMA/133 cmd 0xf881e200 ctl 0xf881e238 bmdma 0x00000000 irq 0
[ 78.167664] ata6: SATA max UDMA/133 cmd 0xf881e280 ctl 0xf881e2b8 bmdma 0x00000000 irq 0
[ 78.175472] ata7: SATA max UDMA/133 cmd 0xf881e300 ctl 0xf881e338 bmdma 0x00000000 irq 0
[ 78.183099] ata8: SATA max UDMA/133 cmd 0xf881e380 ctl 0xf881e3b8 bmdma 0x00000000 irq 0
[ 78.676722] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 78.697172] ata5.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 78.704683] ata5.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 78.712191] ata5.00: 490234752 sectors, multi 0: LBA48
[ 78.737112] ata5.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 78.744592] ata5.00: configured for UDMA/133
[ 79.236129] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 79.256570] ata6.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.264101] ata6.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 79.271619] ata6.00: 490234752 sectors, multi 0: LBA48
[ 79.296521] ata6.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.304040] ata6.00: configured for UDMA/133
[ 79.795538] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 79.815978] ata7.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.823495] ata7.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 79.831032] ata7.00: 490234752 sectors, multi 0: LBA48
[ 79.855930] ata7.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 79.863472] ata7.00: configured for UDMA/133
[ 80.354946] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 80.375384] ata8.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 80.382952] ata8.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 80.390513] ata8.00: 490234752 sectors, multi 0: LBA48
[ 80.415342] ata8.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 80.422877] ata8.00: configured for UDMA/133
[ 80.430470] scsi 4:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 80.438232] sd 4:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
[ 80.445848] sd 4:0:0:0: [sde] Write Protect is off
[ 80.453366] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 80.453383] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 80.461109] sd 4:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
[ 80.468723] sd 4:0:0:0: [sde] Write Protect is off
[ 80.476237] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 80.476252] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 80.483922] sde: unknown partition table
[ 87.806745] sd 4:0:0:0: [sde] Attached SCSI disk
[ 87.814366] scsi 5:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 87.822071] sd 5:0:0:0: [sdf] 490234752 512-byte hardware sectors (251000 MB)
[ 87.829682] sd 5:0:0:0: [sdf] Write Protect is off
[ 87.837329] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 87.837344] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 87.845348] sd 5:0:0:0: [sdf] 490234752 512-byte hardware sectors (251000 MB)
[ 87.853458] sd 5:0:0:0: [sdf] Write Protect is off
[ 87.861397] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 87.861412] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 87.869672] sdf: unknown partition table
[ 95.284548] sd 5:0:0:0: [sdf] Attached SCSI disk
[ 95.293075] scsi 6:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 95.301680] sd 6:0:0:0: [sdg] 490234752 512-byte hardware sectors (251000 MB)
[ 95.310178] sd 6:0:0:0: [sdg] Write Protect is off
[ 95.318525] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 95.318539] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 95.327110] sd 6:0:0:0: [sdg] 490234752 512-byte hardware sectors (251000 MB)
[ 95.335614] sd 6:0:0:0: [sdg] Write Protect is off
[ 95.343981] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 95.343995] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 95.352533] sdg: unknown partition table
[ 102.740714] sd 6:0:0:0: [sdg] Attached SCSI disk
[ 102.749171] scsi 7:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 102.757758] sd 7:0:0:0: [sdh] 490234752 512-byte hardware sectors (251000 MB)
[ 102.766256] sd 7:0:0:0: [sdh] Write Protect is off
[ 102.774610] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 102.774626] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 102.783186] sd 7:0:0:0: [sdh] 490234752 512-byte hardware sectors (251000 MB)
[ 102.791650] sd 7:0:0:0: [sdh] Write Protect is off
[ 102.799970] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 102.799984] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 102.808492] sdh: unknown partition table
[ 110.116127] sd 7:0:0:0: [sdh] Attached SCSI disk
[ 110.124553] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 19
[ 110.143509] scsi8 : sata_promise
[ 110.151883] scsi9 : sata_promise
[ 110.160052] scsi10 : sata_promise
[ 110.168136] scsi11 : sata_promise
[ 110.176031] ata9: SATA max UDMA/133 cmd 0xf8820200 ctl 0xf8820238 bmdma 0x00000000 irq 0
[ 110.184099] ata10: SATA max UDMA/133 cmd 0xf8820280 ctl 0xf88202b8 bmdma 0x00000000 irq 0
[ 110.192172] ata11: SATA max UDMA/133 cmd 0xf8820300 ctl 0xf8820338 bmdma 0x00000000 irq 0
[ 110.200062] ata12: SATA max UDMA/133 cmd 0xf8820380 ctl 0xf88203b8 bmdma 0x00000000 irq 0
[ 110.692889] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 110.713389] ata9.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 110.721175] ata9.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 110.728956] ata9.00: 490234752 sectors, multi 0: LBA48
[ 110.753329] ata9.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 110.761077] ata9.00: configured for UDMA/133
[ 111.252296] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 111.272785] ata10.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.280580] ata10.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 111.288370] ata10.00: 490234752 sectors, multi 0: LBA48
[ 111.312741] ata10.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.320533] ata10.00: configured for UDMA/133
[ 111.811705] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 111.832188] ata11.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.839981] ata11.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 111.847786] ata11.00: 490234752 sectors, multi 0: LBA48
[ 111.872156] ata11.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 111.879951] ata11.00: configured for UDMA/133
[ 112.371114] ata12: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 112.391607] ata12.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 112.399417] ata12.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 112.407218] ata12.00: 490234752 sectors, multi 0: LBA48
[ 112.431552] ata12.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 112.439320] ata12.00: configured for UDMA/133
[ 112.447134] scsi 8:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.455125] sd 8:0:0:0: [sdi] 490234752 512-byte hardware sectors (251000 MB)
[ 112.462964] sd 8:0:0:0: [sdi] Write Protect is off
[ 112.470702] sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 112.470717] sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.478673] sd 8:0:0:0: [sdi] 490234752 512-byte hardware sectors (251000 MB)
[ 112.486513] sd 8:0:0:0: [sdi] Write Protect is off
[ 112.494254] sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 112.494268] sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.502167] sdi: unknown partition table
[ 112.529588] sd 8:0:0:0: [sdi] Attached SCSI disk
[ 112.537413] scsi 9:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.545323] sd 9:0:0:0: [sdj] 490234752 512-byte hardware sectors (251000 MB)
[ 112.553145] sd 9:0:0:0: [sdj] Write Protect is off
[ 112.561007] sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 112.561021] sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.569190] sd 9:0:0:0: [sdj] 490234752 512-byte hardware sectors (251000 MB)
[ 112.577468] sd 9:0:0:0: [sdj] Write Protect is off
[ 112.585577] sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 112.585591] sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.593829] sdj: unknown partition table
[ 112.617892] sd 9:0:0:0: [sdj] Attached SCSI disk
[ 112.626370] scsi 10:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.634936] sd 10:0:0:0: [sdk] 490234752 512-byte hardware sectors (251000 MB)
[ 112.643405] sd 10:0:0:0: [sdk] Write Protect is off
[ 112.651729] sd 10:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 112.651744] sd 10:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.660296] sd 10:0:0:0: [sdk] 490234752 512-byte hardware sectors (251000 MB)
[ 112.668776] sd 10:0:0:0: [sdk] Write Protect is off
[ 112.677116] sd 10:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 112.677136] sd 10:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.685648] sdk: unknown partition table
[ 112.717384] sd 10:0:0:0: [sdk] Attached SCSI disk
[ 112.725810] scsi 11:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 112.734392] sd 11:0:0:0: [sdl] 490234752 512-byte hardware sectors (251000 MB)
[ 112.742893] sd 11:0:0:0: [sdl] Write Protect is off
[ 112.751255] sd 11:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 112.751269] sd 11:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.759834] sd 11:0:0:0: [sdl] 490234752 512-byte hardware sectors (251000 MB)
[ 112.768308] sd 11:0:0:0: [sdl] Write Protect is off
[ 112.776644] sd 11:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 112.776657] sd 11:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 112.785186] sdl: unknown partition table
[ 112.815809] sd 11:0:0:0: [sdl] Attached SCSI disk
[ 112.824267] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 112.850639] scsi12 : sata_promise
[ 112.859064] scsi13 : sata_promise
[ 112.867290] scsi14 : sata_promise
[ 112.875389] scsi15 : sata_promise
[ 112.883301] ata13: SATA max UDMA/133 cmd 0xf8822200 ctl 0xf8822238 bmdma 0x00000000 irq 0
[ 112.891386] ata14: SATA max UDMA/133 cmd 0xf8822280 ctl 0xf88222b8 bmdma 0x00000000 irq 0
[ 112.899281] ata15: SATA max UDMA/133 cmd 0xf8822300 ctl 0xf8822338 bmdma 0x00000000 irq 0
[ 112.906993] ata16: SATA max UDMA/133 cmd 0xf8822380 ctl 0xf88223b8 bmdma 0x00000000 irq 0
[ 113.400028] ata13: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 113.420538] ata13.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 113.428125] ata13.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 113.435704] ata13.00: 490234752 sectors, multi 0: LBA48
[ 113.460465] ata13.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 113.468012] ata13.00: configured for UDMA/133
[ 113.959436] ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 113.979922] ata14.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 113.987525] ata14.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 113.995118] ata14.00: 490234752 sectors, multi 0: LBA48
[ 114.019875] ata14.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 114.027476] ata14.00: configured for UDMA/133
[ 114.518843] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 114.539331] ata15.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 114.546918] ata15.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133
[ 114.554531] ata15.00: 490234752 sectors, multi 0: LBA48
[ 114.579302] ata15.00: ata_hpa_resize 1: sectors = 490234752, hpa_sectors = 490234752
[ 114.586895] ata15.00: configured for UDMA/133
[ 114.918403] ata16: SATA link down (SStatus 0 SControl 0)
[ 114.926018] scsi 12:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 114.933755] sd 12:0:0:0: [sdm] 490234752 512-byte hardware sectors (251000 MB)
[ 114.941420] sd 12:0:0:0: [sdm] Write Protect is off
[ 114.948955] sd 12:0:0:0: [sdm] Mode Sense: 00 3a 00 00
[ 114.948971] sd 12:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 114.956622] sd 12:0:0:0: [sdm] 490234752 512-byte hardware sectors (251000 MB)
[ 114.964258] sd 12:0:0:0: [sdm] Write Protect is off
[ 114.971763] sd 12:0:0:0: [sdm] Mode Sense: 00 3a 00 00
[ 114.971777] sd 12:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 114.979404] sdm: unknown partition table
[ 115.004878] sd 12:0:0:0: [sdm] Attached SCSI disk
[ 115.012514] scsi 13:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 115.020224] sd 13:0:0:0: [sdn] 490234752 512-byte hardware sectors (251000 MB)
[ 115.027883] sd 13:0:0:0: [sdn] Write Protect is off
[ 115.035414] sd 13:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 115.035430] sd 13:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.043070] sd 13:0:0:0: [sdn] 490234752 512-byte hardware sectors (251000 MB)
[ 115.050705] sd 13:0:0:0: [sdn] Write Protect is off
[ 115.058187] sd 13:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 115.058200] sd 13:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.065817] sdn: unknown partition table
[ 115.092809] sd 13:0:0:0: [sdn] Attached SCSI disk
[ 115.100723] scsi 14:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5
[ 115.108931] sd 14:0:0:0: [sdo] 490234752 512-byte hardware sectors (251000 MB)
[ 115.117005] sd 14:0:0:0: [sdo] Write Protect is off
[ 115.125124] sd 14:0:0:0: [sdo] Mode Sense: 00 3a 00 00
[ 115.125139] sd 14:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.133606] sd 14:0:0:0: [sdo] 490234752 512-byte hardware sectors (251000 MB)
[ 115.142171] sd 14:0:0:0: [sdo] Write Protect is off
[ 115.150580] sd 14:0:0:0: [sdo] Mode Sense: 00 3a 00 00
[ 115.150595] sd 14:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.159136] sdo: unknown partition table
[ 115.185583] sd 14:0:0:0: [sdo] Attached SCSI disk
[ 115.194181] pata_via 0000:00:0f.1: version 0.3.1
[ 115.194253] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 20
[ 115.202806] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 115.211316] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
next prev parent reply other threads:[~2007-08-15 16:18 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-08-14 3:04 Still having problems with sata_promise on all late kernels Brad Campbell
2007-08-14 4:37 ` Still having problems with sata_promise on all late kernels - shutdown too Brad Campbell
2007-08-14 16:42 ` Still having problems with sata_promise on all late kernels - shutdown too - BISECTED Brad Campbell
2007-08-15 7:50 ` Tejun Heo
2007-08-15 16:18 ` Brad Campbell [this message]
2007-08-16 5:43 ` Tejun Heo
2007-08-16 7:54 ` Brad Campbell
2007-08-16 11:10 ` Tejun Heo
2007-08-16 11:22 ` Brad Campbell
2007-08-14 10:20 ` Still having problems with sata_promise on all late kernels Tejun Heo
2007-08-14 10:42 ` Brad Campbell
2007-08-14 13:52 ` Brad Campbell
2007-08-15 7:54 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46C3273F.1070306@wasp.net.au \
--to=brad@wasp.net.au \
--cc=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.