Linux version 2.6.22-gentoo-r8 (root@gamma2) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #3 SMP Sun Oct 7 04:50:46 CEST 2007 Command line: root=/dev/sda6 vga=0x305 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009b800 (usable) BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007fed0000 (usable) BIOS-e820: 000000007fed0000 - 000000007fedf000 (ACPI NVS) BIOS-e820: 000000007fedf000 - 0000000080000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 155) 0 entries of 256 used Entering add_active_range(0, 256, 523984) 1 entries of 256 used end_pfn_map = 1048576 DMI present. ACPI: RSDP 000F66C0, 0024 (r2 PTLTD ) ACPI: XSDT 7FED5685, 008C (r1 MEDION MEDIONAG 6040000 LTP 0) ACPI: FACP 7FEDBBD2, 00F4 (r3 INTEL CRESTLNE 6040000 ALAN 1) ACPI: DSDT 7FED6A51, 510D (r2 INTEL CRESTLNE 6040000 INTL 20050624) ACPI: FACS 7FEDEFC0, 0040 ACPI: APIC 7FEDBCC6, 0068 (r1 INTEL CRESTLNE 6040000 LOHR 5A) ACPI: HPET 7FEDBD2E, 0038 (r1 INTEL CRESTLNE 6040000 LOHR 5A) ACPI: MCFG 7FEDBD66, 003C (r1 INTEL CRESTLNE 6040000 LOHR 5A) ACPI: TCPA 7FEDBDA2, 0032 (r1 Intel CRESTLN 6040000 5A52) ACPI: TMOR 7FEDBDD4, 0026 (r1 PTLTD 6040000 PTL 3) ACPI: APIC 7FEDBDFA, 0068 (r1 PTLTD APIC 6040000 LTP 0) ACPI: SLIC 7FEDBE62, 0176 (r1 MEDION MEDIONAG 6040000 LTP 1) ACPI: BOOT 7FEDBFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SSDT 7FED676D, 02E4 (r1 SataRe SataAhci 1000 INTL 20050624) ACPI: SSDT 7FED5C9D, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050624) ACPI: SSDT 7FED5BF7, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050624) ACPI: SSDT 7FED5711, 04E6 (r1 PmRef CpuPm 3000 INTL 20050624) ACPI: BIOS bug: multiple APIC/MADT found, using 0 ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org Entering add_active_range(0, 0, 155) 0 entries of 256 used Entering add_active_range(0, 256, 523984) 1 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 early_node_map[2] active PFN ranges 0: 0 -> 155 0: 256 -> 523984 On node 0 totalpages: 523883 DMA zone: 56 pages used for memmap DMA zone: 1364 pages reserved DMA zone: 2575 pages, LIFO batch:0 DMA32 zone: 7107 pages used for memmap DMA32 zone: 512781 pages, LIFO batch:31 Normal zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 32688 bytes of per cpu data Built 1 zonelists. Total pages: 515356 Kernel command line: root=/dev/sda6 vga=0x305 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Extended CMOS year: 2000 Marking TSC unstable due to TSCs unsynchronized time.c: Detected 1995.000 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture... Memory: 2058024k/2095936k available (3200k kernel code, 37360k reserved, 1380k data, 224k init) SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 Calibrating delay using timer specific routine.. 3995.79 BogoMIPS (lpj=7991584) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K using mwait in idle threads. CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring handled by SMI SMP alternatives: switching to UP code ACPI: Core revision 20070126 Using local APIC timer interrupts. result 12468757 Detected 12.468 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 3990.14 BogoMIPS (lpj=7980296) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a Brought up 2 CPUs migration_cost=27 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - efffffff ACPI: System BIOS is requesting _OSI(Linux) ACPI: Please test with "acpi_osi=!Linux" Please send dmidecode to linux-acpi@vger.kernel.org ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-GART: No AMD northbridge found. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz pnp: 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved pnp: 00:04: iomem range 0xfed00000-0xfed003ff could not be reserved PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0 PCI: Bridge: 0000:00:01.0 IO window: 2000-2fff MEM window: c8000000-caffffff PREFETCH window: d0000000-dfffffff PCI: Bridge: 0000:00:1c.0 IO window: 3000-3fff MEM window: f6000000-f7ffffff PREFETCH window: f0000000-f1ffffff PCI: Bridge: 0000:00:1c.1 IO window: 4000-4fff MEM window: f8000000-f9ffffff PREFETCH window: f2000000-f3ffffff PCI: Bridge: 0000:00:1c.2 IO window: 5000-5fff MEM window: fa000000-fbffffff PREFETCH window: f4000000-f5ffffff PCI: Bridge: 0000:00:1c.3 IO window: 6000-6fff MEM window: c4000000-c5ffffff PREFETCH window: cc000000-cdffffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.1 to 64 ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.2 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 Time: hpet clocksource has been installed. IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 131072 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x36 set to 0x1 Total HugeTLB memory allocated, 0 fuse init (API version 7.8) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie02] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.2:pcie00] Allocate Port Service[0000:00:1c.2:pcie02] Allocate Port Service[0000:00:1c.2:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] hpet_resources: 0xfed00000 is busy Generic RTC Driver v1.07 Linux agpgart interface v0.102 (c) Dave Jones vesafb: framebuffer at 0xc9000000, mapped to 0xffffc20010100000, using 1536k, total 14336k vesafb: mode is 1024x768x8, linelength=1024, pages=3 vesafb: scrolling: redraw vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device ACPI: AC Adapter [AC] (off-line) ACPI: Battery Slot [BAT0] (battery present) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] input: Lid Switch as /class/input/input2 ACPI: Lid Switch [LID0] input: Sleep Button (CM) as /class/input/input3 ACPI: Sleep Button (CM) [SLPB] set_level status: 0 ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no) ACPI: SSDT 7FED642B, 027A (r1 PmRef Cpu0Ist 3000 INTL 20050624) ACPI: SSDT 7FED5EFC, 04AA (r1 PmRef Cpu0Cst 3001 INTL 20050624) Monitor-Mwait will be used to enter C-1 state Monitor-Mwait will be used to enter C-2 state Monitor-Mwait will be used to enter C-3 state ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 7FED66A5, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624) ACPI: SSDT 7FED63A6, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Thermal Zone [TZ00] (52 C) ACPI: Thermal Zone [TZ01] (55 C) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded PPP generic driver version 2.4.2 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:06:00.0 to 64 eth0: RTL8101e at 0xffffc20000036000, 00:40:d0:b7:bc:ef, IRQ 18 netconsole: not configured, aborting Linux video capture interface: v2.00 ahci 0000:00:1f.2: version 2.2 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci ata1: SATA max UDMA/133 cmd 0xffffc20000038100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314 ata2: SATA max UDMA/133 cmd 0xffffc20000038180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314 ata3: SATA max UDMA/133 cmd 0xffffc20000038200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: WDC WD1600BEVS-00RST0, 04.01G04, max UDMA/133 ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 ata_piix 0000:00:1f.1: version 2.11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1f.1 to 64 scsi3 : ata_piix scsi4 : ata_piix ata4: PATA max UDMA/100 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000118a0 irq 14 ata5: PATA max UDMA/100 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x00000000000118a8 irq 15 ata4.00: ATAPI: TOSHIBA DVDW/HD TS-L802A, TU04, max UDMA/33 ata4.00: configured for UDMA/33 scsi 3:0:0:0: CD-ROM TOSHIBA DVDW/HD TS-L802A TU04 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 3:0:0:0: Attached scsi CD-ROM sr0 sr 3:0:0:0: Attached scsi generic sg1 type 5 Fusion MPT base driver 3.04.04 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.04 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc204800 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc204c00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800 usb 1-4: new high speed USB device using ehci_hcd and address 2 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820 usb 1-4: configuration #1 chosen from 1 choice usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 2-5: new high speed USB device using ehci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected usb 2-5: configuration #1 chosen from 1 choice usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input4 rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19 Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000 input: SynPS/2 Synaptics TouchPad as /class/input/input5 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 4 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' ieee80211_crypt: registered algorithm 'CCMP' ieee80211_crypt: registered algorithm 'TKIP' rtc_cmos 00:07: setting the system clock to 2007-10-23 13:16:37 (1193145397) ReiserFS: sda6: found reiserfs format "3.5" with standard journal ReiserFS: sda6: using ordered data mode ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda6: checking transaction log (sda6) scsi 5:0:0:0: Direct-Access Generic- SD/MMC/MS/MSPro 1.00 PQ: 0 ANSI: 0 CCS sd 5:0:0:0: [sdb] Attached SCSI removable disk sd 5:0:0:0: Attached scsi generic sg2 type 0 usb-storage: device scan complete ReiserFS: sda6: replayed 530 transactions in 5 seconds ReiserFS: sda6: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 224k freed iwl4965: Intel(R) Wireless WiFi Link 4965AGN driver for Linux, 1.1.17ds iwl4965: Copyright(c) 2003-2007 Intel Corporation ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:02:00.0 to 64 iwl4965: Detected Intel Wireless WiFi Link 4965AGN nvidia: module license 'NVIDIA' taints kernel. iwl4965: Radio disabled by HW RF Kill switch ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA /var/tmp/portage/media-sound/alsa-driver-9999/work/alsa-driver/pci/hda/hda_codec.c:2142: hda_codec: model 'acer' is selected ReiserFS: sda6: Removing [35261 2093141 0x0 SD]..done ReiserFS: sda6: Removing [35261 2093139 0x0 SD]..done ReiserFS: sda6: Removing [490554 1970234 0x0 SD]..done ReiserFS: sda6: Removing [35261 300826 0x0 SD]..done ReiserFS: sda6: Removing [35261 300791 0x0 SD]..done ReiserFS: sda6: Removing [35261 299584 0x0 SD]..done ReiserFS: sda6: Removing [35261 236179 0x0 SD]..done ReiserFS: sda6: There were 7 uncompleted unlinks/truncates. Completed FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! Adding 1044184k swap on /dev/sda7. Priority:-1 extents:1 across:1044184k r8169: eth0: link down ADDRCONF(NETDEV_UP): eth0: link is not ready NVRM: Xid (0001:00): 34 ALSA /var/tmp/portage/media-sound/alsa-driver-9999/work/alsa-driver/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:576: hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x008b0000 NVRM: Xid (0001:00): 34